lkml.org 
[lkml]   [2002]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] 2.5.31 Summit NUMA patch with dynamic IRQ balancing -- now with ACPI
Date
Here's the latest iteration of my 2.5 Summit chipset patch.  It contains 
feedback from Andi Kleen and an ACPI hack so that kernels built with ACPI's
"CPU Enumeration only" hyperthread option will boot properly.

Important safety note: Since this patch should remove the need for
balance_cpu on P4 systems (and no others need it), the patch deletes it and
associated functions. You have been warned. Use only as directed. Actual
highway mileage may vary. Batteries not included.

--
James Cleverdon
IBM xSeries Linux Solutions
{jamesclv(Unix, preferred), cleverdj(Notes)} at us dot ibm dot com
diff -ruN 2.5.31/arch/i386/kernel/acpi.c t31/arch/i386/kernel/acpi.c
--- 2.5.31/arch/i386/kernel/acpi.c Sat Aug 10 18:41:53 2002
+++ t31/arch/i386/kernel/acpi.c Tue Aug 27 15:48:42 2002
@@ -130,6 +130,8 @@
printk(KERN_INFO PREFIX "Local APIC address 0x%08x\n",
madt->lapic_address);

+ acpi_madt_oem_check(madt->header.oem_id, madt->header.oem_table_id);
+
return 0;
}

@@ -364,18 +366,21 @@
return result;
}

+#ifndef CONFIG_ACPI_HT_ONLY
result = acpi_table_parse_madt(ACPI_MADT_LAPIC_NMI, acpi_parse_lapic_nmi);
if (result < 0) {
printk(KERN_ERR PREFIX "Error parsing LAPIC NMI entry\n");
/* TBD: Cleanup to allow fallback to MPS */
return result;
}
+#endif /*!CONFIG_ACPI_HT_ONLY*/

acpi_lapic = 1;

#endif /*CONFIG_X86_LOCAL_APIC*/

#ifdef CONFIG_X86_IO_APIC
+#ifndef CONFIG_ACPI_HT_ONLY

/*
* I/O APIC
@@ -413,11 +418,14 @@

acpi_ioapic = 1;

+#endif /*!CONFIG_ACPI_HT_ONLY*/
#endif /*CONFIG_X86_IO_APIC*/

#ifdef CONFIG_X86_LOCAL_APIC
- if (acpi_lapic && acpi_ioapic)
+ if (acpi_lapic && acpi_ioapic) {
smp_found_config = 1;
+ smp_cluster_apic_check();
+ }
#endif

return 0;
diff -ruN 2.5.31/arch/i386/kernel/apic.c t31/arch/i386/kernel/apic.c
--- 2.5.31/arch/i386/kernel/apic.c Sat Aug 10 18:41:29 2002
+++ t31/arch/i386/kernel/apic.c Tue Aug 27 17:09:21 2002
@@ -29,6 +29,7 @@
#include <asm/mtrr.h>
#include <asm/mpspec.h>
#include <asm/pgalloc.h>
+#include <asm/smpboot.h>

/* Using APIC to generate smp_local_timer_interrupt? */
int using_apic_timer = 0;
@@ -272,6 +273,16 @@
apic_write_around(APIC_LVT1, value);
}

+static inline unsigned long apic_ldr_value(unsigned long value)
+{
+ if (clustered_apic_numaq)
+ return (value);
+ if (clustered_apic_xapic)
+ return (((value) & ~APIC_LDR_MASK) |
+ SET_APIC_LOGICAL_ID(xapic_physical_to_logical_apicid(hard_smp_processor_id())));
+ return (((value) & ~APIC_LDR_MASK) | SET_APIC_LOGICAL_ID(1UL << smp_processor_id()));
+}
+
void __init setup_local_APIC (void)
{
unsigned long value, ver, maxlvt;
@@ -304,21 +315,22 @@
* document number 292116). So here it goes...
*/

- if (!clustered_apic_mode) {
+ if (!clustered_apic_numaq) {
/*
- * In clustered apic mode, the firmware does this for us
- * Put the APIC into flat delivery mode.
- * Must be "all ones" explicitly for 82489DX.
+ * For NUMA-Q, the firmware does this for us. Otherwise, put the APIC into clustered or flat
+ *
+ * delivery mode. Must be "all ones" explicitly for 82489DX.
*/
- apic_write_around(APIC_DFR, 0xffffffff);
+ if (clustered_apic_mode)
+ apic_write_around(APIC_DFR, APIC_DFR_CLUSTER);
+ else
+ apic_write_around(APIC_DFR, APIC_DFR_FLAT);

/*
* Set up the logical destination ID.
*/
value = apic_read(APIC_LDR);
- value &= ~APIC_LDR_MASK;
- value |= (1<<(smp_processor_id()+24));
- apic_write_around(APIC_LDR, value);
+ apic_write_around(APIC_LDR, apic_ldr_value(value));
}

/*
diff -ruN 2.5.31/arch/i386/kernel/io_apic.c t31/arch/i386/kernel/io_apic.c
--- 2.5.31/arch/i386/kernel/io_apic.c Sat Aug 10 18:41:26 2002
+++ t31/arch/i386/kernel/io_apic.c Tue Aug 27 17:15:06 2002
@@ -35,6 +35,7 @@
#include <asm/io.h>
#include <asm/smp.h>
#include <asm/desc.h>
+#include <asm/smpboot.h>

#undef APIC_LOCKUP_DEBUG

@@ -213,60 +214,6 @@

#endif

-#define IDLE_ENOUGH(cpu,now) \
- (idle_cpu(cpu) && ((now) - irq_stat[(cpu)].idle_timestamp > 1))
-
-#define IRQ_ALLOWED(cpu,allowed_mask) \
- ((1 << cpu) & (allowed_mask))
-
-#if CONFIG_SMP
-static unsigned long move(int curr_cpu, unsigned long allowed_mask, unsigned long now, int direction)
-{
- int search_idle = 1;
- int cpu = curr_cpu;
-
- goto inside;
-
- do {
- if (unlikely(cpu == curr_cpu))
- search_idle = 0;
-inside:
- if (direction == 1) {
- cpu++;
- if (cpu >= NR_CPUS)
- cpu = 0;
- } else {
- cpu--;
- if (cpu == -1)
- cpu = NR_CPUS-1;
- }
- } while (!cpu_online(cpu) || !IRQ_ALLOWED(cpu,allowed_mask) ||
- (search_idle && !IDLE_ENOUGH(cpu,now)));
-
- return cpu;
-}
-
-static inline void balance_irq(int irq)
-{
- irq_balance_t *entry = irq_balance + irq;
- unsigned long now = jiffies;
-
- if (entry->timestamp != now) {
- unsigned long allowed_mask;
- int random_number;
-
- rdtscl(random_number);
- random_number &= 1;
-
- allowed_mask = cpu_online_map & irq_affinity[irq];
- entry->timestamp = now;
- entry->cpu = move(entry->cpu, allowed_mask, now, random_number);
- set_ioapic_affinity(irq, 1 << entry->cpu);
- }
-}
-#else /* !SMP */
-static inline void balance_irq(int irq) { }
-#endif

/*
* support for broken MP BIOSs, enables hand-redirection of PIRQ0-7 to
@@ -682,9 +629,39 @@
return current_vector;
}

+/*
+ * round_robin_cpu_apic_id -- Since i386 Linux doesn't use the APIC TPRs to
+ * set task/interrupt priority, xAPICs' tiebreaker rule tends to hit one CPU
+ * with all interrupts for each quad. Distribute the interrupts using a
+ * simple round robin scheme.
+ */
+static int round_robin_cpu_apic_id(void)
+{
+ int val;
+ static unsigned next_cpu = 0;
+
+ if (next_cpu >= NR_CPUS || cpu_2_logical_apicid[next_cpu] == BAD_APICID)
+ next_cpu = 0;
+ val = cpu_present_to_apicid(next_cpu) | APIC_DEST_CPUS_MASK;
+ ++next_cpu;
+ return (val);
+}
+
+static inline int target_cpus(void)
+{
+ if (clustered_apic_numaq)
+ return APIC_BROADCAST_ID_APIC; /* broadcast to local quad */
+ if (clustered_apic_xapic)
+ return round_robin_cpu_apic_id();
+ return logical_cpu_present_map & 0xFFu;
+}
+
static struct hw_interrupt_type ioapic_level_irq_type;
static struct hw_interrupt_type ioapic_edge_irq_type;

+#undef KERN_DEBUG
+#define KERN_DEBUG
+
void __init setup_IO_APIC_irqs(void)
{
struct IO_APIC_route_entry entry;
@@ -702,9 +679,9 @@
memset(&entry,0,sizeof(entry));

entry.delivery_mode = dest_LowestPrio;
- entry.dest_mode = INT_DELIVERY_MODE;
+ entry.dest_mode = INT_DEST_ADDR_MODE;
entry.mask = 0; /* enable IRQ */
- entry.dest.logical.logical_dest = TARGET_CPUS;
+ entry.dest.logical.logical_dest = target_cpus();

idx = find_irq_entry(apic,pin,mp_INT);
if (idx == -1) {
@@ -722,7 +699,6 @@
if (irq_trigger(idx)) {
entry.trigger = 1;
entry.mask = 1;
- entry.dest.logical.logical_dest = TARGET_CPUS;
}

irq = pin_2_irq(idx, apic, pin);
@@ -782,9 +758,9 @@
* We use logical delivery to get the timer IRQ
* to the first CPU.
*/
- entry.dest_mode = INT_DELIVERY_MODE;
+ entry.dest_mode = INT_DEST_ADDR_MODE;
entry.mask = 0; /* unmask IRQ now */
- entry.dest.logical.logical_dest = TARGET_CPUS;
+ entry.dest.logical.logical_dest = target_cpus();
entry.delivery_mode = dest_LowestPrio;
entry.polarity = 0;
entry.trigger = 0;
@@ -1141,7 +1117,7 @@

old_id = mp_ioapics[apic].mpc_apicid;

- if (mp_ioapics[apic].mpc_apicid >= 0xf) {
+ if (mp_ioapics[apic].mpc_apicid >= apic_broadcast_id) {
printk(KERN_ERR "BIOS bug, IO-APIC#%d ID is %d in the MPC table!...\n",
apic, mp_ioapics[apic].mpc_apicid);
printk(KERN_ERR "... fixing up to %d. (tell your hw vendor)\n",
@@ -1153,14 +1129,16 @@
* Sanity check, is the ID really free? Every APIC in a
* system must have a unique ID or we get lots of nice
* 'stuck on smp_invalidate_needed IPI wait' messages.
+ * I/O APIC IDs no longer have any meaning for xAPICs.
*/
- if (phys_id_present_map & (1 << mp_ioapics[apic].mpc_apicid)) {
+ if (!clustered_apic_xapic &&
+ (phys_id_present_map & (1 << mp_ioapics[apic].mpc_apicid))) {
printk(KERN_ERR "BIOS bug, IO-APIC#%d ID %d is already used!...\n",
apic, mp_ioapics[apic].mpc_apicid);
for (i = 0; i < 0xf; i++)
if (!(phys_id_present_map & (1 << i)))
break;
- if (i >= 0xf)
+ if (i >= apic_broadcast_id)
panic("Max APIC ID exceeded!\n");
printk(KERN_ERR "... fixing up to %d. (tell your hw vendor)\n",
i);
@@ -1288,7 +1266,6 @@
*/
static void ack_edge_ioapic_irq(unsigned int irq)
{
- balance_irq(irq);
if ((irq_desc[irq].status & (IRQ_PENDING | IRQ_DISABLED))
== (IRQ_PENDING | IRQ_DISABLED))
mask_IO_APIC_irq(irq);
@@ -1328,7 +1305,6 @@
unsigned long v;
int i;

- balance_irq(irq);
/*
* It appears there is an erratum which affects at least version 0x11
* of I/O APIC (that's the 82093AA and cores integrated into various
@@ -1849,8 +1825,8 @@
memset(&entry,0,sizeof(entry));

entry.delivery_mode = dest_LowestPrio;
- entry.dest_mode = INT_DELIVERY_MODE;
- entry.dest.logical.logical_dest = TARGET_CPUS;
+ entry.dest_mode = INT_DEST_ADDR_MODE;
+ entry.dest.logical.logical_dest = target_cpus();
entry.mask = 1; /* Disabled (masked) */
entry.trigger = 1; /* Level sensitive */
entry.polarity = 1; /* Low active */
diff -ruN 2.5.31/arch/i386/kernel/irq.c t31/arch/i386/kernel/irq.c
--- 2.5.31/arch/i386/kernel/irq.c Sat Aug 10 18:41:19 2002
+++ t31/arch/i386/kernel/irq.c Thu Aug 22 17:57:45 2002
@@ -332,6 +332,7 @@

irq_enter();
kstat.irqs[cpu][irq]++;
+ apic_adj_tpr(TPR_IRQ);
spin_lock(&desc->lock);
desc->handler->ack(irq);
/*
@@ -389,6 +390,7 @@
*/
desc->handler->end(irq);
spin_unlock(&desc->lock);
+ apic_adj_tpr(-TPR_IRQ);

irq_exit();

diff -ruN 2.5.31/arch/i386/kernel/mpparse.c t31/arch/i386/kernel/mpparse.c
--- 2.5.31/arch/i386/kernel/mpparse.c Sat Aug 10 18:41:25 2002
+++ t31/arch/i386/kernel/mpparse.c Tue Aug 27 17:18:47 2002
@@ -30,6 +30,7 @@
#include <asm/mpspec.h>
#include <asm/pgalloc.h>
#include <asm/io_apic.h>
+#include <asm/smpboot.h>

/* Have we found an MP table */
int smp_found_config;
@@ -68,6 +69,13 @@

/* Bitmask of physically existing CPUs */
unsigned long phys_cpu_present_map;
+unsigned long logical_cpu_present_map;
+
+u32 apic_broadcast_id = APIC_BROADCAST_ID_APIC;
+u8 clustered_apic_mode = 0;
+u8 esr_disable = 0;
+u8 raw_phys_apicid[NR_CPUS] = { [0 ... NR_CPUS-1] = BAD_APICID };
+static u8 clustered_hint = 0;

/*
* Intel MP BIOS table parsing routines:
@@ -104,8 +112,8 @@
if (!(m->mpc_cpuflag & CPU_ENABLED))
return;

- logical_apicid = m->mpc_apicid;
- if (clustered_apic_mode) {
+ logical_apicid = 0x01;
+ if (clustered_apic_numaq) {
quad = translation_table[mpc_record]->trans_quad;
logical_apicid = (quad << 4) +
(m->mpc_apicid ? m->mpc_apicid << 1 : 1);
@@ -186,11 +194,8 @@
}
ver = m->mpc_apicver;

- if (clustered_apic_mode) {
- phys_cpu_present_map |= (logical_apicid&0xf) << (4*quad);
- } else {
- phys_cpu_present_map |= 1 << m->mpc_apicid;
- }
+ logical_cpu_present_map |= 1 << (num_processors-1);
+ phys_cpu_present_map |= apicid_to_phys_cpu_present(m->mpc_apicid);
/*
* Validate version
*/
@@ -199,6 +204,7 @@
ver = 0x10;
}
apic_version[m->mpc_apicid] = ver;
+ raw_phys_apicid[num_processors - 1] = m->mpc_apicid;
}

static void __init MP_bus_info (struct mpc_config_bus *m)
@@ -209,7 +215,7 @@
memcpy(str, m->mpc_bustype, 6);
str[6] = 0;

- if (clustered_apic_mode) {
+ if (clustered_apic_numaq) {
quad = translation_table[mpc_record]->trans_quad;
mp_bus_id_to_node[m->mpc_busid] = quad;
mp_bus_id_to_local[m->mpc_busid] = translation_table[mpc_record]->trans_local;
@@ -234,10 +240,23 @@
}
}

+static int __init ioapic_dup_check(unsigned long apicaddr)
+{
+ register int i;
+
+ for (i = nr_ioapics; --i >= 0; ) {
+ if (mp_ioapics[i].mpc_apicaddr == apicaddr)
+ return 1; /* Got a dup. */
+ }
+ return 0; /* No dup. */
+}
+
static void __init MP_ioapic_info (struct mpc_config_ioapic *m)
{
if (!(m->mpc_flags & MPC_APIC_USABLE))
return;
+ if (ioapic_dup_check(m->mpc_apicaddr))
+ return;

printk("I/O APIC #%d Version %d at 0x%lX.\n",
m->mpc_apicid, m->mpc_apicver, m->mpc_apicaddr);
@@ -253,6 +272,15 @@
}
mp_ioapics[nr_ioapics] = *m;
nr_ioapics++;
+ /******
+ * Warning! We have an APIC version number collision between the APICs
+ * on Scorpio-based NUMA-Q boxes and Summit xAPICs. Intel didn't
+ * define the xAPIC ver ID range until late in the development cycle,
+ * so there is working silicon out there that doesn't match it.
+ * A test in smp_cluster_apic_check() resolves the above conflict.
+ ******/
+ if (m->mpc_apicver >= XAPIC_VER_LOW && m->mpc_apicver <= XAPIC_VER_HIGH)
+ clustered_hint |= CLUSTERED_APIC_XAPIC;
}

static void __init MP_intsrc_info (struct mpc_config_intsrc *m)
@@ -348,12 +376,37 @@
}

/*
+ * Common code for MPS and ACPI/MADT.
+ */
+void __init smp_cluster_apic_check(void)
+{
+ static const char *mode_names[] = {
+ "Flat", "Clustered NUMA-Q", "Clustered xAPIC", "???"
+ };
+
+ if (clustered_hint) {
+ if (clustered_hint & CLUSTERED_APIC_NUMAQ) {
+ /* NUMA-Q boxes never had xAPICs */
+ clustered_hint &= ~CLUSTERED_APIC_XAPIC;
+ }
+ clustered_apic_mode = clustered_hint;
+ esr_disable = 1;
+ if (clustered_apic_xapic)
+ apic_broadcast_id = APIC_BROADCAST_ID_XAPIC;
+ phys_cpu_present_map = logical_cpu_present_map;
+ }
+ printk("Enabling APIC mode: %s. Using %d I/O APICs\n",
+ mode_names[clustered_apic_mode], nr_ioapics);
+}
+
+/*
* Read/parse the MPC
*/

static int __init smp_read_mpc(struct mp_config_table *mpc)
{
- char str[16];
+ char oem[10];
+ char prod[14];
int count=sizeof(*mpc);
unsigned char *mpt=((unsigned char *)mpc)+count;

@@ -378,13 +431,21 @@
printk(KERN_ERR "SMP mptable: null local APIC address!\n");
return 0;
}
- memcpy(str,mpc->mpc_oem,8);
- str[8]=0;
- printk("OEM ID: %s ",str);
-
- memcpy(str,mpc->mpc_productid,12);
- str[12]=0;
- printk("Product ID: %s ",str);
+ memcpy(oem, mpc->mpc_oem, 8);
+ oem[8] = 0;
+ memcpy(prod, mpc->mpc_productid, 12);
+ prod[12] = 0;
+ printk("OEM ID: %s ", oem);
+ printk("Product ID: %s ",prod);
+ /*
+ * Can't recognize Summit xAPICs (see MP_ioapic_info), so use
+ * OEM/Product IDs.
+ */
+ if (!strncmp(oem, "IBM ENSW", 8) &&
+ (!strncmp(prod, "NF 6000R", 8) || !strncmp(prod, "VIGIL SMP", 9)) )
+ clustered_hint |= CLUSTERED_APIC_XAPIC;
+ else if (!strncmp(oem, "IBM NUMA", 8))
+ clustered_hint |= CLUSTERED_APIC_NUMAQ;

printk("APIC at: 0x%lX\n",mpc->mpc_lapic);

@@ -395,7 +456,7 @@
if (!acpi_lapic)
mp_lapic_addr = mpc->mpc_lapic;

- if (clustered_apic_mode && mpc->mpc_oemptr) {
+ if (clustered_apic_numaq && mpc->mpc_oemptr) {
/* We need to process the oem mpc tables to tell us which quad things are in ... */
mpc_record = 0;
smp_read_mpc_oem((struct mp_config_oemtable *) mpc->mpc_oemptr, mpc->mpc_oemsize);
@@ -463,6 +524,7 @@
}
++mpc_record;
}
+ smp_cluster_apic_check();
if (!num_processors)
printk(KERN_ERR "SMP mptable: no processors registered!\n");
return num_processors;
@@ -640,10 +702,8 @@
* ACPI supports both logical (e.g. Hyper-Threading) and physical
* processors, where MPS only supports physical.
*/
- if (acpi_lapic && acpi_ioapic) {
+ if (acpi_lapic && acpi_ioapic)
printk(KERN_INFO "Using ACPI (MADT) for SMP configuration information\n");
- return;
- }
else if (acpi_lapic)
printk(KERN_INFO "Using ACPI for processor (LAPIC) configuration information\n");

@@ -898,6 +958,8 @@
{
int idx = 0;

+ if (ioapic_dup_check(address))
+ return;
if (nr_ioapics >= MAX_IO_APICS) {
printk(KERN_ERR "ERROR: Max # of I/O APICs (%d) exceeded "
"(found %d)\n", MAX_IO_APICS, nr_ioapics);
@@ -934,6 +996,17 @@
mp_ioapic_routing[idx].irq_start,
mp_ioapic_routing[idx].irq_end);

+ /******
+ * Warning! We have an APIC version number collision between the APICs
+ * on Scorpio-based NUMA-Q boxes and Summit xAPICs. Intel didn't
+ * define the xAPIC ver ID range until late in the development cycle,
+ * so there is working silicon out there that doesn't match it.
+ * A test in smp_cluster_apic_check() resolves the above conflict.
+ ******/
+ if (mp_ioapics[idx].mpc_apicver >= XAPIC_VER_LOW &&
+ mp_ioapics[idx].mpc_apicver <= XAPIC_VER_HIGH)
+ clustered_hint |= CLUSTERED_APIC_XAPIC;
+
return;
}

@@ -1051,6 +1124,13 @@
return;
}

+/* Hook from generic ACPI tables.c */
+void __init acpi_madt_oem_check(char *oem_id, char *oem_table_id)
+{
+ if (!strncmp(oem_id, "IBM", 3) && !strncmp(oem_table_id, "SERVIGIL", 8))
+ clustered_hint |= CLUSTERED_APIC_XAPIC;
+}
+
#ifdef CONFIG_ACPI_PCI

void __init mp_parse_prt (void)
diff -ruN 2.5.31/arch/i386/kernel/process.c t31/arch/i386/kernel/process.c
--- 2.5.31/arch/i386/kernel/process.c Sat Aug 10 18:41:15 2002
+++ t31/arch/i386/kernel/process.c Thu Aug 22 17:57:45 2002
@@ -145,7 +145,9 @@
irq_stat[smp_processor_id()].idle_timestamp = jiffies;
while (!need_resched())
idle();
+ apic_set_tpr(TPR_TASK);
schedule();
+ apic_set_tpr(TPR_IDLE);
}
}

@@ -197,7 +199,7 @@
}
/* we will leave sorting out the final value
when we are ready to reboot, since we might not
- have set up boot_cpu_id or smp_num_cpu */
+ have set up boot_cpu_physical_apicid or smp_num_cpu */
break;
#endif
}
diff -ruN 2.5.31/arch/i386/kernel/smpboot.c t31/arch/i386/kernel/smpboot.c
--- 2.5.31/arch/i386/kernel/smpboot.c Sat Aug 10 18:41:28 2002
+++ t31/arch/i386/kernel/smpboot.c Tue Aug 27 17:10:34 2002
@@ -498,59 +498,23 @@
return do_fork(CLONE_VM|CLONE_IDLETASK, 0, &regs, 0);
}

-/* which physical APIC ID maps to which logical CPU number */
-volatile int physical_apicid_2_cpu[MAX_APICID];
/* which logical CPU number maps to which physical APIC ID */
-volatile int cpu_2_physical_apicid[NR_CPUS];
+volatile u8 cpu_2_physical_apicid[NR_CPUS] = { [0 ... NR_CPUS-1] = BAD_APICID };

-/* which logical APIC ID maps to which logical CPU number */
-volatile int logical_apicid_2_cpu[MAX_APICID];
/* which logical CPU number maps to which logical APIC ID */
-volatile int cpu_2_logical_apicid[NR_CPUS];
+volatile u8 cpu_2_logical_apicid[NR_CPUS] = { [0 ... NR_CPUS-1] = BAD_APICID };

-static inline void init_cpu_to_apicid(void)
-/* Initialize all maps between cpu number and apicids */
-{
- int apicid, cpu;
-
- for (apicid = 0; apicid < MAX_APICID; apicid++) {
- physical_apicid_2_cpu[apicid] = -1;
- logical_apicid_2_cpu[apicid] = -1;
- }
- for (cpu = 0; cpu < NR_CPUS; cpu++) {
- cpu_2_physical_apicid[cpu] = -1;
- cpu_2_logical_apicid[cpu] = -1;
- }
-}

-static inline void map_cpu_to_boot_apicid(int cpu, int apicid)
-/*
- * set up a mapping between cpu and apicid. Uses logical apicids for multiquad,
- * else physical apic ids
- */
+static inline void map_cpu_to_boot_apicid(int cpu, u8 phys_apicid, u8 log_apicid)
{
- if (clustered_apic_mode) {
- logical_apicid_2_cpu[apicid] = cpu;
- cpu_2_logical_apicid[cpu] = apicid;
- } else {
- physical_apicid_2_cpu[apicid] = cpu;
- cpu_2_physical_apicid[cpu] = apicid;
- }
+ cpu_2_logical_apicid[cpu] = log_apicid;
+ cpu_2_physical_apicid[cpu] = phys_apicid;
}

-static inline void unmap_cpu_to_boot_apicid(int cpu, int apicid)
-/*
- * undo a mapping between cpu and apicid. Uses logical apicids for multiquad,
- * else physical apic ids
- */
+static inline void unmap_cpu_to_boot_apicid(int cpu, u8 phys_apicid, u8 log_apicid)
{
- if (clustered_apic_mode) {
- logical_apicid_2_cpu[apicid] = -1;
- cpu_2_logical_apicid[cpu] = -1;
- } else {
- physical_apicid_2_cpu[apicid] = -1;
- cpu_2_physical_apicid[cpu] = -1;
- }
+ cpu_2_logical_apicid[cpu] = BAD_APICID;
+ cpu_2_physical_apicid[cpu] = BAD_APICID;
}

#if APIC_DEBUG
@@ -764,7 +728,7 @@

extern unsigned long cpu_initialized;

-static void __init do_boot_cpu (int apicid)
+static void __init do_boot_cpu(u8 phys_apicid, u8 log_apicid)
/*
* NOTE - on most systems this is a PHYSICAL apic ID, but on multiquad
* (ie clustered apic addressing mode), this is a LOGICAL apic ID.
@@ -774,7 +738,7 @@
unsigned long boot_error = 0;
int timeout, cpu;
unsigned long start_eip;
- unsigned short nmi_high, nmi_low;
+ unsigned short nmi_high = 0, nmi_low = 0;

cpu = ++cpucount;
/*
@@ -791,7 +755,7 @@
*/
init_idle(idle, cpu);

- map_cpu_to_boot_apicid(cpu, apicid);
+ map_cpu_to_boot_apicid(cpu, phys_apicid, log_apicid);

idle->thread.eip = (unsigned long) start_secondary;

@@ -801,7 +765,8 @@
start_eip = setup_trampoline();

/* So we see what's up */
- printk("Booting processor %d/%d eip %lx\n", cpu, apicid, start_eip);
+ printk("Booting processor %d/0x%02X/0x%02X eip 0x%lX\n",
+ cpu, phys_apicid, log_apicid, start_eip);
stack_start.esp = (void *) (1024 + PAGE_SIZE + (char *)idle->thread_info);

/*
@@ -813,7 +778,7 @@

Dprintk("Setting warm reset code and vector.\n");

- if (clustered_apic_mode) {
+ if (clustered_apic_numaq) {
/* stash the current NMI vector, so we can put things back */
nmi_high = *((volatile unsigned short *) TRAMPOLINE_HIGH);
nmi_low = *((volatile unsigned short *) TRAMPOLINE_LOW);
@@ -830,7 +795,7 @@
/*
* Be paranoid about clearing APIC errors.
*/
- if (!clustered_apic_mode && APIC_INTEGRATED(apic_version[apicid])) {
+ if (!clustered_apic_mode && APIC_INTEGRATED(apic_version[phys_apicid])) {
apic_read_around(APIC_SPIV);
apic_write(APIC_ESR, 0);
apic_read(APIC_ESR);
@@ -845,10 +810,10 @@
* Starting actual IPI sequence...
*/

- if (clustered_apic_mode)
- boot_error = wakeup_secondary_via_NMI(apicid);
- else
- boot_error = wakeup_secondary_via_INIT(apicid, start_eip);
+ if (clustered_apic_numaq)
+ boot_error = wakeup_secondary_via_NMI(log_apicid);
+ else
+ boot_error = wakeup_secondary_via_INIT(phys_apicid, start_eip);

if (!boot_error) {
/*
@@ -883,14 +848,15 @@
/* trampoline code not run */
printk("Not responding.\n");
#if APIC_DEBUG
+ /* xAPICs don't do remote inquiries. */
if (!clustered_apic_mode)
- inquire_remote_apic(apicid);
+ inquire_remote_apic(phys_apicid);
#endif
}
}
if (boot_error) {
/* Try to put things back the way they were before ... */
- unmap_cpu_to_boot_apicid(cpu, apicid);
+ unmap_cpu_to_boot_apicid(cpu, phys_apicid, log_apicid);
clear_bit(cpu, &cpu_callout_map); /* was set here (do_boot_cpu()) */
clear_bit(cpu, &cpu_initialized); /* was set by cpu_init() */
cpucount--;
@@ -899,7 +865,7 @@
/* mark "stuck" area as not stuck */
*((volatile unsigned long *)phys_to_virt(8192)) = 0;

- if(clustered_apic_mode) {
+ if (clustered_apic_numaq) {
printk("Restoring NMI vector\n");
*((volatile unsigned short *) TRAMPOLINE_HIGH) = nmi_high;
*((volatile unsigned short *) TRAMPOLINE_LOW) = nmi_low;
@@ -958,7 +924,6 @@
extern int prof_old_multiplier[NR_CPUS];
extern int prof_counter[NR_CPUS];

-static int boot_cpu_logical_apicid;
/* Where the IO area was mapped on multiquad, always 0 otherwise */
void *xquad_portio;

@@ -966,9 +931,11 @@

static void __init smp_boot_cpus(unsigned int max_cpus)
{
- int apicid, cpu, bit;
+ int cpu, bit;
+ u8 phys_apicid, log_apicid;

- if (clustered_apic_mode && (numnodes > 1)) {
+#ifdef CONFIG_MULTIQUAD
+ if (clustered_apic_numaq && (numnodes > 1)) {
printk("Remapping cross-quad port I/O for %d quads\n",
numnodes);
printk("xquad_portio vaddr 0x%08lx, len %08lx\n",
@@ -977,6 +944,7 @@
xquad_portio = ioremap (XQUAD_PORTIO_BASE,
numnodes * XQUAD_PORTIO_LEN);
}
+#endif

#ifdef CONFIG_MTRR
/* Must be done before other processors booted */
@@ -993,8 +961,6 @@
prof_multiplier[cpu] = 1;
}

- init_cpu_to_apicid();
-
/*
* Setup boot CPU information
*/
@@ -1007,8 +973,14 @@
*/
set_bit(0, &cpu_online_map);
set_bit(0, &cpu_callout_map);
- boot_cpu_logical_apicid = logical_smp_processor_id();
- map_cpu_to_boot_apicid(0, boot_cpu_apicid);
+ if (clustered_apic_xapic)
+ boot_cpu_logical_apicid = xapic_physical_to_logical_apicid(boot_cpu_physical_apicid);
+ else if (clustered_apic_numaq)
+ boot_cpu_logical_apicid = logical_smp_processor_id();
+ else
+ boot_cpu_logical_apicid = 0x01;
+ map_cpu_to_boot_apicid(0, boot_cpu_physical_apicid, boot_cpu_logical_apicid);
+ printk("Boot CPU #0/0x%02X/0x%02X\n", boot_cpu_physical_apicid, boot_cpu_logical_apicid);

current_thread_info()->cpu = 0;
smp_tune_scheduling();
@@ -1085,28 +1057,44 @@
*/
Dprintk("CPU present map: %lx\n", phys_cpu_present_map);

- for (bit = 0; bit < NR_CPUS; bit++) {
- apicid = cpu_present_to_apicid(bit);
+ for (cpu = 1, bit = 0; bit < NR_CPUS; bit++) {
+ if (!(logical_cpu_present_map & (1ul << bit)))
+ continue;
+ if ((max_cpus >= 0) && (max_cpus <= cpucount + 1))
+ continue;
+ phys_apicid = raw_phys_apicid[bit];
/*
* Don't even attempt to start the boot CPU!
*/
- if (apicid == boot_cpu_apicid)
+ if (phys_apicid == boot_cpu_physical_apicid)
continue;
-
- if (!(phys_cpu_present_map & (1 << bit)))
- continue;
- if (max_cpus <= cpucount+1)
+ if (phys_apicid == BAD_APICID)
continue;
+ if (clustered_apic_xapic)
+ log_apicid = (u8)xapic_physical_to_logical_apicid(phys_apicid);
+ else if (clustered_apic_numaq)
+ log_apicid = ((bit >> 2) << 4) | (1 << (bit & 0x3));
+ else {
+ /* Yes, this overflows if cpu > 7. The APIC
+ * destination register is only 8 bits wide.
+ * For more than 8 CPUs, must use clustered mode. */
+ log_apicid = 1u << cpu;
+ if (log_apicid == 0)
+ BUG();
+ }

- do_boot_cpu(apicid);
+ do_boot_cpu(phys_apicid, log_apicid);

/*
* Make sure we unmap all failed CPUs
*/
- if ((boot_apicid_to_cpu(apicid) == -1) &&
- (phys_cpu_present_map & (1 << bit)))
- printk("CPU #%d not responding - cannot use it.\n",
- apicid);
+ if ((cpu_2_physical_apicid[cpu] == BAD_APICID) &&
+ (logical_cpu_present_map & (1ul << bit))) {
+ printk("CPU #%d/0x%02X/0x%02X not responding - cannot use it.\n",
+ bit, phys_apicid, log_apicid);
+ logical_cpu_present_map &= ~(1ul << bit);
+ } else
+ ++cpu; /* Got a live one. */
}

/*
diff -ruN 2.5.31/arch/i386/kernel/trampoline.S t31/arch/i386/kernel/trampoline.S
--- 2.5.31/arch/i386/kernel/trampoline.S Sat Aug 10 18:41:27 2002
+++ t31/arch/i386/kernel/trampoline.S Thu Aug 22 17:57:45 2002
@@ -36,9 +36,7 @@

ENTRY(trampoline_data)
r_base = .
-#ifdef CONFIG_MULTIQUAD
wbinvd
-#endif /* CONFIG_MULTIQUAD */
mov %cs, %ax # Code and data in the same place
mov %ax, %ds

diff -ruN 2.5.31/include/asm-i386/acpi.h t31/include/asm-i386/acpi.h
--- 2.5.31/include/asm-i386/acpi.h Sat Aug 10 18:41:53 2002
+++ t31/include/asm-i386/acpi.h Tue Aug 27 15:47:27 2002
@@ -138,6 +138,9 @@
/* early initialization routine */
extern void acpi_reserve_bootmem(void);

+/* Check for special HW using OEM name lists */
+extern void acpi_madt_oem_check(char *oem_id, char *oem_table_id);
+
#endif /*CONFIG_ACPI_SLEEP*/

#endif /*__KERNEL__*/
diff -ruN 2.5.31/include/asm-i386/apic.h t31/include/asm-i386/apic.h
--- 2.5.31/include/asm-i386/apic.h Sat Aug 10 18:42:05 2002
+++ t31/include/asm-i386/apic.h Thu Aug 22 17:57:45 2002
@@ -64,6 +64,22 @@
apic_write_around(APIC_EOI, 0);
}

+static inline void apic_set_tpr(unsigned long val)
+{
+ unsigned long value;
+
+ value = apic_read(APIC_TASKPRI);
+ apic_write_around(APIC_TASKPRI, (value & ~APIC_TPRI_MASK) + val);
+}
+
+static inline void apic_adj_tpr(long adj)
+{
+ unsigned long value;
+
+ value = apic_read(APIC_TASKPRI);
+ apic_write_around(APIC_TASKPRI, value + adj);
+}
+
extern int get_maxlvt(void);
extern void clear_local_APIC(void);
extern void connect_bsp_APIC (void);
@@ -96,6 +112,15 @@
#define NMI_LOCAL_APIC 2
#define NMI_INVALID 3

+#else /* CONFIG_X86_LOCAL_APIC */
+#define apic_set_tpr(val)
+#define apic_adj_tpr(adj)
#endif /* CONFIG_X86_LOCAL_APIC */

+/* Priority values for apic_adj_tpr() and apic_set_tpr() */
+/* xAPICs only do priority comparisons on the upper nibble. */
+#define TPR_IDLE (0x00L)
+#define TPR_TASK (0x10L)
+#define TPR_IRQ (0x10L)
+
#endif /* __ASM_APIC_H */
diff -ruN 2.5.31/include/asm-i386/apicdef.h t31/include/asm-i386/apicdef.h
--- 2.5.31/include/asm-i386/apicdef.h Sat Aug 10 18:41:36 2002
+++ t31/include/asm-i386/apicdef.h Thu Aug 22 17:57:45 2002
@@ -11,8 +11,10 @@
#define APIC_DEFAULT_PHYS_BASE 0xfee00000

#define APIC_ID 0x20
-#define APIC_ID_MASK (0x0F<<24)
-#define GET_APIC_ID(x) (((x)>>24)&0x0F)
+#define APIC_ID_MASK (0xFF<<24)
+#define GET_APIC_ID(x) (((x)>>24)&0xFF)
+#define XAPIC_VER_LOW 0x14 /* Version num range */
+#define XAPIC_VER_HIGH 0x1F
#define APIC_LVR 0x30
#define APIC_LVR_MASK 0xFF00FF
#define GET_APIC_VERSION(x) ((x)&0xFF)
@@ -32,6 +34,8 @@
#define SET_APIC_LOGICAL_ID(x) (((x)<<24))
#define APIC_ALL_CPUS 0xFF
#define APIC_DFR 0xE0
+#define APIC_DFR_CLUSTER 0x0FFFFFFFul /* Clustered */
+#define APIC_DFR_FLAT 0xFFFFFFFFul /* Flat mode */
#define APIC_SPIV 0xF0
#define APIC_SPIV_FOCUS_DISABLED (1<<9)
#define APIC_SPIV_APIC_ENABLED (1<<8)
@@ -58,6 +62,7 @@
#define APIC_INT_ASSERT 0x04000
#define APIC_ICR_BUSY 0x01000
#define APIC_DEST_LOGICAL 0x00800
+#define APIC_DEST_PHYSICAL 0x0 /* For symmetry */
#define APIC_DM_FIXED 0x00000
#define APIC_DM_LOWEST 0x00100
#define APIC_DM_SMI 0x00200
@@ -108,7 +113,13 @@

#define APIC_BASE (fix_to_virt(FIX_APIC_BASE))

-#define MAX_IO_APICS 8
+#define MAX_IO_APICS 32 /* Summit boxes can have 4*(2+3*2) I/O APICs */
+
+/*
+ * The intr broadcast ID is 0xF for old APICs and 0xFF for xAPICs.
+ */
+#define APIC_BROADCAST_ID_XAPIC 0xFF
+#define APIC_BROADCAST_ID_APIC 0x0F

/*
* the local APIC register structure, memory mapped. Not terribly well
diff -ruN 2.5.31/include/asm-i386/mpspec.h t31/include/asm-i386/mpspec.h
--- 2.5.31/include/asm-i386/mpspec.h Sat Aug 10 18:41:16 2002
+++ t31/include/asm-i386/mpspec.h Thu Aug 22 17:57:45 2002
@@ -14,13 +14,10 @@
#define SMP_MAGIC_IDENT (('_'<<24)|('P'<<16)|('M'<<8)|'_')

/*
- * a maximum of 16 APICs with the current APIC ID architecture.
+ * A maximum of 16 APICs with the classic APIC ID architecture.
+ * xAPICs can have up to 256.
*/
-#ifdef CONFIG_MULTIQUAD
#define MAX_APICS 256
-#else /* !CONFIG_MULTIQUAD */
-#define MAX_APICS 16
-#endif /* CONFIG_MULTIQUAD */

#define MAX_MPC_ENTRY 1024

@@ -204,6 +201,7 @@
extern int mp_bus_id_to_pci_bus [MAX_MP_BUSSES];

extern unsigned int boot_cpu_physical_apicid;
+extern unsigned int boot_cpu_logical_apicid;
extern unsigned long phys_cpu_present_map;
extern int smp_found_config;
extern void find_smp_config (void);
diff -ruN 2.5.31/include/asm-i386/smp.h t31/include/asm-i386/smp.h
--- 2.5.31/include/asm-i386/smp.h Sat Aug 10 18:41:18 2002
+++ t31/include/asm-i386/smp.h Tue Aug 27 15:48:36 2002
@@ -19,33 +19,56 @@
#include <asm/io_apic.h>
#endif
#include <asm/apic.h>
-#endif
-#endif
+#endif /* !__ASSEMBLY__ */
+#endif /* CONFIG_X86_LOCAL_APIC */

-#ifdef CONFIG_SMP
-# ifdef CONFIG_MULTIQUAD
-# define TARGET_CPUS 0xf /* all CPUs in *THIS* quad */
-# define INT_DELIVERY_MODE 0 /* physical delivery on LOCAL quad */
-# else
-# define TARGET_CPUS cpu_online_map
-# define INT_DELIVERY_MODE 1 /* logical delivery broadcast to all procs */
-# endif
-#else
-# define INT_DELIVERY_MODE 1 /* logical delivery */
-# define TARGET_CPUS 0x01
-#endif
+#ifndef __ASSEMBLY__
+extern u8 clustered_apic_mode;
+extern u8 esr_disable;
+extern u32 apic_broadcast_id;
+extern unsigned long logical_cpu_present_map;
+extern unsigned long phys_cpu_present_map;
+
+/*
+ * Some lowlevel functions might want to know about
+ * the real APIC ID <-> CPU # mapping.
+ */
+#define MAX_APICID 256
+#define BAD_APICID 0xFFu
+extern volatile u8 cpu_2_physical_apicid[NR_CPUS];
+extern volatile u8 physical_apicid_2_cpu[MAX_APICID];
+extern volatile u8 cpu_2_logical_apicid[NR_CPUS];
+extern volatile u8 logical_apicid_2_cpu[MAX_APICID];
+
+/*
+ * This function is needed by all SMP systems. It must _always_ be valid
+ * from the initial startup. We map APIC_BASE very early in page_setup(),
+ * so this is correct in the x86 case.
+ */
+
+#ifndef CONFIG_X86_LOCAL_APIC
+
+#define clustered_apic_mode (0)
+#define esr_disable (0)
+
+#endif /* !CONFIG_X86_LOCAL_APIC */
+
+#endif /* !__ASSEMBLY__ */
+
+#define CLUSTERED_APIC_NUMAQ 0x01
+#define CLUSTERED_APIC_XAPIC 0x02
+
+#define clustered_apic_numaq (clustered_apic_mode & CLUSTERED_APIC_NUMAQ)
+#define clustered_apic_xapic (clustered_apic_mode & CLUSTERED_APIC_XAPIC)
+
+#define APIC_DEST_CPUS_MASK 0x0Fu /* Destination masks for */
+#define APIC_DEST_CLUSTER_MASK 0xF0u /* clustered mode. */
+#define INT_DEST_ADDR_MODE 1 /* logical delivery */

-#ifndef clustered_apic_mode
- #ifdef CONFIG_MULTIQUAD
- #define clustered_apic_mode (1)
- #define esr_disable (1)
- #else /* !CONFIG_MULTIQUAD */
- #define clustered_apic_mode (0)
- #define esr_disable (0)
- #endif /* CONFIG_MULTIQUAD */
-#endif

#ifdef CONFIG_SMP
+#define smp_processor_id() (current->processor)
+
#ifndef __ASSEMBLY__

/*
@@ -53,7 +76,6 @@
*/

extern void smp_alloc_memory(void);
-extern unsigned long phys_cpu_present_map;
extern unsigned long cpu_online_map;
extern volatile unsigned long smp_invalidate_needed;
extern int pic_mode;
@@ -67,16 +89,7 @@
extern void smp_invalidate_rcv(void); /* Process an NMI */
extern void (*mtrr_hook) (void);
extern void zap_low_mappings (void);
-
-/*
- * Some lowlevel functions might want to know about
- * the real APIC ID <-> CPU # mapping.
- */
-#define MAX_APICID 256
-extern volatile int cpu_to_physical_apicid[NR_CPUS];
-extern volatile int physical_apicid_to_cpu[MAX_APICID];
-extern volatile int cpu_to_logical_apicid[NR_CPUS];
-extern volatile int logical_apicid_to_cpu[MAX_APICID];
+extern void smp_cluster_apic_check(void); /* cluster mode test */

/*
* This function is needed by all SMP systems. It must _always_ be valid
@@ -123,7 +136,7 @@

#endif /* !__ASSEMBLY__ */

-#define NO_PROC_ID 0xFF /* No processor magic marker */
+#define NO_PROC_ID 0xFFu /* No processor magic marker */

-#endif
-#endif
+#endif /* CONFIG_SMP */
+#endif /* __ASM_SMP_H */
diff -ruN 2.5.31/include/asm-i386/smpboot.h t31/include/asm-i386/smpboot.h
--- 2.5.31/include/asm-i386/smpboot.h Sat Aug 10 18:41:55 2002
+++ t31/include/asm-i386/smpboot.h Tue Aug 27 17:15:47 2002
@@ -1,62 +1,42 @@
#ifndef __ASM_SMPBOOT_H
#define __ASM_SMPBOOT_H

-#ifndef clustered_apic_mode
- #ifdef CONFIG_MULTIQUAD
- #define clustered_apic_mode (1)
- #else /* !CONFIG_MULTIQUAD */
- #define clustered_apic_mode (0)
- #endif /* CONFIG_MULTIQUAD */
-#endif
-
-#ifdef CONFIG_MULTIQUAD
- #define TRAMPOLINE_LOW phys_to_virt(0x8)
- #define TRAMPOLINE_HIGH phys_to_virt(0xa)
-#else /* !CONFIG_MULTIQUAD */
- #define TRAMPOLINE_LOW phys_to_virt(0x467)
- #define TRAMPOLINE_HIGH phys_to_virt(0x469)
-#endif /* CONFIG_MULTIQUAD */
-
-#ifdef CONFIG_MULTIQUAD
- #define boot_cpu_apicid boot_cpu_logical_apicid
-#else /* !CONFIG_MULTIQUAD */
- #define boot_cpu_apicid boot_cpu_physical_apicid
-#endif /* CONFIG_MULTIQUAD */
+#ifndef __ASM_SMP_H
+#include "asm/smp.h"
+#endif
+
+#define TRAMPOLINE_LOW phys_to_virt(clustered_apic_numaq?0x8:0x467)
+#define TRAMPOLINE_HIGH phys_to_virt(clustered_apic_numaq?0xa:0x469)
+
+/*
+ * To build the logical APIC ID for each CPU we have three cases:
+ * 1) Normal flat mode: use a bitmap of the CPU numbers
+ * 2) NUMA-Q: do nothing, the BIOS has set it up
+ * 3) xAPIC: convert the Intel standard physical APIC ID to a cluster
+ * nibble/cpu bitmap nibble
+ */
+/* cpu index numbr: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, ... */
+/* phys xAPIC IDs : 00, 01, 02, 03, 10, 11, 12, 13, 20, 21, 22, ... */
+/* logical APIC ID: 01, 02, 04, 08, 11, 12, 14, 18, 21, 22, 24, ... */
+#define xapic_physical_to_logical_apicid(phys_apic) ((1ul << ((phys_apic) & 0x3)) | ((phys_apic) & APIC_DEST_CLUSTER_MASK))

/*
- * How to map from the cpu_present_map
+ * How to map from phys_cpu_present_map.
+ * 1) Normal flat mode: use the mps_cpu, apicid bitmap
+ * 2) Multi-Quad: only 4 CPUs per cluster, cluster ID in high nibble
*/
-#ifdef CONFIG_MULTIQUAD
- #define cpu_present_to_apicid(mps_cpu) ( ((mps_cpu/4)*16) + (1<<(mps_cpu%4)) )
-#else /* !CONFIG_MULTIQUAD */
- #define cpu_present_to_apicid(apicid) (apicid)
-#endif /* CONFIG_MULTIQUAD */
+#define cpu_present_to_apicid(cpu) (cpu_to_logical_apicid(cpu))
+extern unsigned char raw_phys_apicid[NR_CPUS];
+#define apicid_to_phys_cpu_present(apicid) (clustered_apic_mode ? (1ul << ((((apicid) >> 4) << 2) | ((apicid) & 0x3))) : (1ul << (apicid)))

/*
* Mappings between logical cpu number and logical / physical apicid
- * The first four macros are trivial, but it keeps the abstraction consistent
*/
-extern volatile int logical_apicid_2_cpu[];
-extern volatile int cpu_2_logical_apicid[];
-extern volatile int physical_apicid_2_cpu[];
-extern volatile int cpu_2_physical_apicid[];
-
-#define logical_apicid_to_cpu(apicid) logical_apicid_2_cpu[apicid]
-#define cpu_to_logical_apicid(cpu) cpu_2_logical_apicid[cpu]
-#define physical_apicid_to_cpu(apicid) physical_apicid_2_cpu[apicid]
-#define cpu_to_physical_apicid(cpu) cpu_2_physical_apicid[cpu]
-#ifdef CONFIG_MULTIQUAD /* use logical IDs to bootstrap */
-#define boot_apicid_to_cpu(apicid) logical_apicid_2_cpu[apicid]
-#define cpu_to_boot_apicid(cpu) cpu_2_logical_apicid[cpu]
-#else /* !CONFIG_MULTIQUAD */ /* use physical IDs to bootstrap */
-#define boot_apicid_to_cpu(apicid) physical_apicid_2_cpu[apicid]
-#define cpu_to_boot_apicid(cpu) cpu_2_physical_apicid[cpu]
-#endif /* CONFIG_MULTIQUAD */
-
-
-#ifdef CONFIG_MULTIQUAD
-#else /* !CONFIG_MULTIQUAD */
-#endif /* CONFIG_MULTIQUAD */
+extern volatile u8 cpu_2_logical_apicid[];
+extern volatile u8 cpu_2_physical_apicid[];
+
+#define cpu_to_logical_apicid(cpu) (int)cpu_2_logical_apicid[cpu]
+#define cpu_to_physical_apicid(cpu) (int)cpu_2_physical_apicid[cpu]


#endif
\
 
 \ /
  Last update: 2005-03-22 13:28    [W:0.056 / U:23.912 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site