lkml.org 
[lkml]   [2002]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 2.4.20-pre4-ac2] fix broken i810_audio DMA (?)
From
Date
F*ck. This time the patch attached.
Thanx Jim.

George

On Thu, 2002-08-29 at 03:39, Juergen Sawinski wrote:
> Changes:
> -remove dma reset in stop_{dac,adc}
> (from ICH4 manual: contents of all Bus master related registers to be
> reset; so, probably some registers are not re-initilized properly on
> consecutive re-opening of /dev/dsp ???)
> -remove writes to OFF_CIV, instead set LVI relative to CIV
>
> and some stuff that was already in the last diff I send to the list:
> -implement a codec ID <-> IO register offset mapping
> -in i810_ioctl, case SNDCTL_DSP_CHANNELS: only touch bits 20:21
> off GLOB_CNT (multichannel capabilities)
> -AMD 8111 has 6 hw channels so I must have mmio (but I don't have
> any docs to verify this)
> -minor fixes
>
> --
> Juergen "George" Sawinski
> Max-Planck Institute for Medical Research
> Dept. of Biomedical Optics
> Jahnstr. 29
> D-69120 Heidelberg
> Germany
>
> Phone: +49-6221-486-308
> Fax: +49-6221-486-325
>
> priv.
> Phone: +49-6221-418 858
> Mobile: +49-171-532 5302
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
Juergen "George" Sawinski
Max-Planck-Institute for Medical Research
Dept. of Biomedical Optics
Jahnstr. 29
D-69120 Heidelberg
Germany

Phone: +49-6221-486-309
Fax: +49-6221-486-325

priv.
Phone: +49-6221-418 848
Mobile: +49-171-532 5302
--- linux-2.4.20-pre4-ac2/drivers/sound/i810_audio.c Tue Aug 27 21:44:25 2002
+++ jsaw/drivers/sound/i810_audio.c Thu Aug 29 03:18:16 2002
@@ -69,12 +69,12 @@
*
* ICH 4 caveats
*
- * The ICH4 has the feature, that the codec ID may not be congruent
- * with the AC-link channel.
+ * The ICH4 has the feature, that the codec ID doesn't have to be
+ * congruent with the IO connection.
*
- * Right now, the codec ID is not the real codec ID but the AC-link
- * channel. A ID <-> AC-link mapping has still to be implemented.
- *
+ * Therefore, from driver version 0.23 on, there is a "codec ID" <->
+ * "IO register base offset" mapping (card->ac97_id_map) field.
+ *
* Juergen "George" Sawinski (jsaw)
*/

@@ -207,7 +207,7 @@
CAS = 0x34 /* Codec Write Semaphore Register */
};

-ENUM_ENGINE(MC2,4); /* Mic. 2 */
+ENUM_ENGINE(MC2,4); /* Mic In 2 */
ENUM_ENGINE(PI2,5); /* PCM In 2 */
ENUM_ENGINE(SP,6); /* S/PDIF */

@@ -234,8 +234,7 @@
#define INT_GPI (1<<0)
#define INT_MASK (INT_SEC|INT_PRI|INT_MC|INT_PO|INT_PI|INT_MO|INT_NI|INT_GPI)

-
-#define DRIVER_VERSION "0.22"
+#define DRIVER_VERSION "0.23"

/* magic numbers to protect our data structures */
#define I810_CARD_MAGIC 0x5072696E /* "Prin" */
@@ -295,7 +294,7 @@
/*@FIXME to be verified*/ { 2, 0x0000 }, /* SI7012 */
/*@FIXME to be verified*/ { 2, 0x0000 }, /* NVIDIA_NFORCE */
/*@FIXME to be verified*/ { 2, 0x0000 }, /* AMD768 */
- /*@FIXME to be verified*/ { 2, 0x0000 }, /* AMD8111 */
+ /*@FIXME to be verified*/ { 3, 0x0001 }, /* AMD8111 */
};

static struct pci_device_id i810_pci_tbl [] __initdata = {
@@ -417,6 +416,7 @@
int dev_audio;

/* structures for abstraction of hardware facilities, codecs, banks and channels*/
+ u16 ac97_id_map[NR_AC97];
struct ac97_codec *ac97_codec[NR_AC97];
struct i810_state *states[NR_HW_CH];
struct i810_channel *channel; /* 1:1 to states[] but diff. lifetime */
@@ -449,6 +449,12 @@
int initializing;
};

+/* extract register offset from codec struct */
+#define IO_REG_OFF(codec) (((struct i810_card *) codec->private_data)->ac97_id_map[codec->id])
+
+/* set LVI from CIV */
+#define CIV_TO_LVI(port, off) outb((inb(port+OFF_CIV)+off) & 31, port+OFF_LVI)
+
static struct i810_card *devs = NULL;

static int i810_open_mixdev(struct inode *inode, struct file *file);
@@ -786,8 +792,6 @@
outb(0, card->iobase + PI_CR);
// wait for the card to acknowledge shutdown
while( inb(card->iobase + PI_CR) != 0 ) ;
- // reset the dma engine now
- outb(0x02, card->iobase + PI_CR);
// now clear any latent interrupt bits (like the halt bit)
if(card->pci_id == PCI_DEVICE_ID_SI_7012)
outb( inb(card->iobase + PI_PICB), card->iobase + PI_PICB );
@@ -838,8 +842,6 @@
outb(0, card->iobase + PO_CR);
// wait for the card to acknowledge shutdown
while( inb(card->iobase + PO_CR) != 0 ) ;
- // reset the dma engine now
- outb(0x02, card->iobase + PO_CR);
// now clear any latent interrupt bits (like the halt bit)
if(card->pci_id == PCI_DEVICE_ID_SI_7012)
outb( inb(card->iobase + PO_PICB), card->iobase + PO_PICB );
@@ -1033,11 +1035,11 @@
}
spin_lock_irqsave(&state->card->lock, flags);
outb(2, state->card->iobase+c->port+OFF_CR); /* reset DMA machine */
+ while( inb(state->card->iobase+c->port+OFF_CR) & 0x02 ) ;
outl((u32)state->card->chandma +
c->num*sizeof(struct i810_channel),
state->card->iobase+c->port+OFF_BDBAR);
- outb(0, state->card->iobase+c->port+OFF_CIV);
- outb(0, state->card->iobase+c->port+OFF_LVI);
+ CIV_TO_LVI(state->card->iobase+c->port, 0);

spin_unlock_irqrestore(&state->card->lock, flags);

@@ -1083,13 +1085,13 @@
if(rec && dmabuf->count < dmabuf->dmasize &&
(dmabuf->trigger & PCM_ENABLE_INPUT))
{
- outb((inb(port+OFF_CIV)+1)&31, port+OFF_LVI);
+ CIV_TO_LVI(port, 1);
__start_adc(state);
while( !(inb(port + OFF_CR) & ((1<<4) | (1<<2))) ) ;
} else if (!rec && dmabuf->count &&
(dmabuf->trigger & PCM_ENABLE_OUTPUT))
{
- outb((inb(port+OFF_CIV)+1)&31, port+OFF_LVI);
+ CIV_TO_LVI(port, 1);
__start_dac(state);
while( !(inb(port + OFF_CR) & ((1<<4) | (1<<2))) ) ;
}
@@ -1802,11 +1804,11 @@
}
if (c != NULL) {
outb(2, state->card->iobase+c->port+OFF_CR); /* reset DMA machine */
+ while ( inb(state->card->iobase+c->port+OFF_CR) & 2 );
outl((u32)state->card->chandma +
c->num*sizeof(struct i810_channel),
state->card->iobase+c->port+OFF_BDBAR);
- outb(0, state->card->iobase+c->port+OFF_CIV);
- outb(0, state->card->iobase+c->port+OFF_LVI);
+ CIV_TO_LVI(state->card->iobase+c->port, 0);
}

spin_unlock_irqrestore(&state->card->lock, flags);
@@ -1948,13 +1950,13 @@

switch ( val ) {
case 2: /* 2 channels is always supported */
- outl(i_glob_cnt & 0xcfffff,
+ outl(i_glob_cnt & 0xffcfffff,
state->card->iobase + GLOB_CNT);
/* Do we need to change mixer settings???? */
break;
case 4: /* Supported on some chipsets, better check first */
if ( state->card->channels >= 4 ) {
- outl((i_glob_cnt & 0xcfffff) | 0x100000,
+ outl((i_glob_cnt & 0xffcfffff) | 0x100000,
state->card->iobase + GLOB_CNT);
/* Do we need to change mixer settings??? */
} else {
@@ -1963,7 +1965,7 @@
break;
case 6: /* Supported on some chipsets, better check first */
if ( state->card->channels >= 6 ) {
- outl((i_glob_cnt & 0xcfffff) | 0x200000,
+ outl((i_glob_cnt & 0xffcfffff) | 0x200000,
state->card->iobase + GLOB_CNT);
/* Do we need to change mixer settings??? */
} else {
@@ -2553,8 +2555,7 @@
{
struct i810_card *card = dev->private_data;
int count = 100;
- u16 reg_set = ((u16) reg) & 0x7f;
- reg_set |= ((u16) dev->id) << 7;
+ u16 reg_set = IO_REG_OFF(dev) | (reg&0x7f);

while(count-- && (readb(card->iobase_mmio + CAS) & 1))
udelay(1);
@@ -2574,7 +2575,7 @@
{
struct i810_card *card = dev->private_data;
int count = 100;
- u8 reg_set = ((dev->id)?((reg&0x7f)|0x80):(reg&0x7f));
+ u16 reg_set = IO_REG_OFF(dev) | (reg&0x7f);

while(count-- && (inb(card->iobase + CAS) & 1))
udelay(1);
@@ -2586,8 +2587,7 @@
{
struct i810_card *card = dev->private_data;
int count = 100;
- u16 reg_set = ((u16) reg) & 0x7f;
- reg_set |= ((u16) dev->id) << 7;
+ u16 reg_set = IO_REG_OFF(dev) | (reg&0x7f);

while(count-- && (readb(card->iobase_mmio + CAS) & 1))
udelay(1);
@@ -2603,7 +2603,7 @@
{
struct i810_card *card = dev->private_data;
int count = 100;
- u8 reg_set = ((dev->id)?((reg&0x7f)|0x80):(reg&0x7f));
+ u16 reg_set = IO_REG_OFF(dev) | (reg&0x7f);

while(count-- && (inb(card->iobase + CAS) & 1))
udelay(1);
@@ -2779,7 +2779,7 @@
if ((card->pci_id == PCI_DEVICE_ID_INTEL_ICH4)
&& (card->use_mmio)) {
primary_codec_id = (int) readl(card->iobase_mmio + SDM) & 0x3;
- printk(KERN_INFO "i810_audio: primary codec id %d\n",
+ printk(KERN_INFO "i810_audio: Primary codec has ID %d\n",
primary_codec_id);
}

@@ -2803,6 +2803,7 @@
int num_ac97 = 0;
int ac97_id;
int total_channels = 0;
+ int nr_ac97_max = card_cap[card->pci_id_internal].nr_ac97;
struct ac97_codec *codec;
u16 eid;
u32 reg;
@@ -2828,13 +2829,15 @@
reg = inl(card->iobase + GLOB_CNT);
outl(reg & 0xffcfffff, card->iobase + GLOB_CNT);

- for (num_ac97 = 0; num_ac97 < card_cap[card->pci_id_internal].nr_ac97; num_ac97++) {
+ for (num_ac97 = 0; num_ac97 < NR_AC97; num_ac97++)
card->ac97_codec[num_ac97] = NULL;
- }

- for (num_ac97 = 0; num_ac97 < card_cap[card->pci_id_internal].nr_ac97; num_ac97++) {
+ /*@FIXME I don't know, if I'm playing to safe here... (jsaw) */
+ if ((nr_ac97_max > 2) && !card->use_mmio) nr_ac97_max = 2;
+
+ for (num_ac97 = 0; num_ac97 < nr_ac97_max; num_ac97++) {
/* codec reset */
- printk(KERN_INFO "i810_audio: resetting hw channel %d\n", num_ac97);
+ printk(KERN_INFO "i810_audio: Resetting connection %d\n", num_ac97);
if (card->use_mmio) readw(card->ac97base_mmio + 0x80*num_ac97);
else inw(card->ac97base + 0x80*num_ac97);

@@ -2846,7 +2849,7 @@
if ((card->pci_id == PCI_DEVICE_ID_INTEL_ICH4)
&& (card->use_mmio)) {
ac97_id = (int) readl(card->iobase_mmio + SDM) & 0x3;
- printk(KERN_INFO "i810_audio: hw channel %d, codec id %d\n",
+ printk(KERN_INFO "i810_audio: Connection %d with codec id %d\n",
num_ac97, ac97_id);
}
else {
@@ -2869,9 +2872,8 @@
/* initialize some basic codec information, other fields will be filled
in ac97_probe_codec */
codec->private_data = card;
-
- /*@FIXME this will lead to problems!!! id=2 <-> io offset=0*/
- codec->id = num_ac97;
+ codec->id = ac97_id;
+ card->ac97_id_map[ac97_id] = num_ac97 * 0x80;

if (card->use_mmio) {
codec->codec_read = i810_ac97_get_mmio;
@@ -2883,7 +2885,7 @@
}

if(!i810_ac97_probe_and_powerup(card,codec)) {
- printk(KERN_ERR "i810_audio: timed out waiting for codec %d analog ready.\n", num_ac97);
+ printk(KERN_ERR "i810_audio: timed out waiting for codec %d analog ready.\n", ac97_id);
kfree(codec);
break; /* it didn't work */
}
@@ -2903,7 +2905,7 @@
codec->codec_write(codec, AC97_EXTENDED_MODEM_ID, 0L);
if(codec->codec_read(codec, AC97_EXTENDED_MODEM_ID))
{
- printk(KERN_WARNING "i810_audio: codec %d is a softmodem - skipping.\n", num_ac97);
+ printk(KERN_WARNING "i810_audio: codec %d is a softmodem - skipping.\n", ac97_id);
kfree(codec);
continue;
}
@@ -3042,8 +3044,7 @@
}
dmabuf->count = dmabuf->dmasize;
stop_dac(state);
- outb(0,card->iobase+dmabuf->write_channel->port+OFF_CIV);
- outb(31,card->iobase+dmabuf->write_channel->port+OFF_LVI);
+ CIV_TO_LVI(card->iobase+dmabuf->write_channel->port, -1);
save_flags(flags);
cli();
start_dac(state);
\
 
 \ /
  Last update: 2005-03-22 13:28    [W:0.051 / U:8.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site