lkml.org 
[lkml]   [2002]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    Subject2.4.20-pre2-ac3 oops
    Hello,

    Linux version 2.4.20-pre2-ac3 (greg@localhost.localdomain) (gcc version 3.2 (Mandrake Linux 9.0 3.2-0.3mdk)) #5 Fri Aug 16 19:37:27 CEST 2002
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
    BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
    BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    511MB LOWMEM available.
    found SMP MP-table at 000fb900
    hm, page 000fb000 reserved twice.
    hm, page 000fc000 reserved twice.
    hm, page 000f6000 reserved twice.
    hm, page 000f7000 reserved twice.
    On node 0 totalpages: 131056
    zone(0): 4096 pages.
    zone(1): 126960 pages.
    zone(2): 0 pages.
    ACPI: Searched entire block, no RSDP was found.
    ACPI: RSDP located at physical address c00fa510
    RSD PTR v0 [AMI ]
    __va_range(0x1fff0000, 0x68): idx=8 mapped at ffff6000
    ACPI table found: RSDT v1 [AMIINT INTEL845 0.16]
    __va_range(0x1fff0030, 0x24): idx=8 mapped at ffff6000
    __va_range(0x1fff0030, 0x81): idx=8 mapped at ffff6000
    ACPI table found: FACP v1 [AMIINT INTEL845 0.17]
    __va_range(0x1fff00c0, 0x24): idx=8 mapped at ffff6000
    __va_range(0x1fff00c0, 0x54): idx=8 mapped at ffff6000
    ACPI table found: APIC v1 [AMIINT INTEL845 0.9]
    __va_range(0x1fff00c0, 0x54): idx=8 mapped at ffff6000
    LAPIC (acpi_id[0x0001] id[0x0] enabled[1])
    CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 16

    IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
    INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
    INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
    1 CPUs total
    Local APIC address fee00000
    Enabling the CPU's according to the ACPI table
    Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
    OEM ID: INTEL Product ID: I845E APIC at: 0xFEE00000
    I/O APIC #2 Version 32 at 0xFEC00000.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Processors: 1
    Kernel command line: BOOT_IMAGE=2.4.20-pre2-ac3 rw root=812 video=matrox:1600x1200-16@75 console=ttyS1
    Initializing CPU#0
    Detected 2220.805 MHz processor.
    Console: colour VGA+ 80x25
    Calibrating delay loop... 4430.23 BogoMIPS
    Memory: 514424k/524224k available (1739k kernel code, 9412k reserved, 423k data, 288k init, 0k highmem)
    Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
    Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
    Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
    CPU: L1 I cache: 0K, L1 D cache: 8K
    CPU: L2 cache: 512K
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: Intel(R) Pentium(R) 4 CPU 2.20GHz stepping 04
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    enabled ExtINT on CPU#0
    ESR value before enabling vector: 00000000
    ESR value after enabling vector: 00000000
    ENABLING IO-APIC IRQs
    Setting 2 in the phys_id_present_map
    ...changing IO-APIC physical APIC ID to 2 ... ok.
    ..TIMER: vector=0x31 pin1=2 pin2=0
    testing the IO APIC.......................

    .................................... done.
    Using local APIC timer interrupts.
    calibrating APIC timer ...
    ..... CPU clock speed is 2220.8330 MHz.
    ..... host bus clock speed is 100.9468 MHz.
    cpu: 0, clocks: 1009468, slice: 504734
    CPU0<T0:1009456,T1:504720,D:2,S:504734,C:1009468>
    mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
    mtrr: detected mtrr type: Intel
    PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last
    bus=3
    PCI: Using configuration type 1
    PCI: Probing PCI hardware
    Unknown bridge resource 0: assuming transparent
    PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
    PCI->APIC IRQ transform: (B0,I29,P0) -> 16
    PCI->APIC IRQ transform: (B0,I29,P1) -> 19
    PCI->APIC IRQ transform: (B0,I29,P3) -> 23
    PCI->APIC IRQ transform: (B0,I31,P0) -> 18
    PCI->APIC IRQ transform: (B0,I31,P1) -> 17
    PCI->APIC IRQ transform: (B0,I31,P1) -> 17
    PCI->APIC IRQ transform: (B1,I0,P0) -> 16
    PCI->APIC IRQ transform: (B3,I0,P0) -> 16
    PCI->APIC IRQ transform: (B3,I1,P0) -> 17
    PCI->APIC IRQ transform: (B3,I2,P0) -> 18
    PCI->APIC IRQ transform: (B3,I3,P0) -> 19
    PCI->APIC IRQ transform: (B3,I4,P0) -> 16
    PCI->APIC IRQ transform: (B3,I8,P0) -> 20
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    PnPBIOS: Found PnP BIOS installation structure at 0xc00f7730
    PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x678b, dseg 0xf0000
    PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
    cpufreq: CPU#0 P4/Xeon(TM) CPU On-Demand Clock Modulation available
    CPU clock: 2220.805 MHz (222.080-2220.805 MHz)
    Starting kswapd
    devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
    devfs: boot_options: 0x1
    matroxfb: Matrox G550 detected
    matroxfb: MTRR's turned on
    matroxfb: 1600x1200x16bpp (virtual: 1600x5241)
    matroxfb: framebuffer at 0xDC000000, mapped to 0xe0805000, size 33554432
    Console: switching to colour frame buffer device 200x75
    fb0: MATROX VGA frame buffer device
    pty: 256 Unix98 ptys configured
    Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
    ttyS00 at 0x03f8 (irq = 4) is a 16550A
    ttyS01 at 0x02f8 (irq = 3) is a 16550A
    Real Time Clock Driver v1.10e
    Non-volatile memory driver v1.1
    i810_rng: RNG not detected
    Uniform Multi-Platform E-IDE driver Revision: 6.31
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    PCI: Unable to reserve I/O region #1:8@0 for device 00:1f.1
    Trying to free nonexistent resource <00000000-00000007>
    Trying to free nonexistent resource <00000000-00000003>
    Trying to free nonexistent resource <00000000-00000007>
    Trying to free nonexistent resource <00000000-00000003>
    Trying to free nonexistent resource <0000fc00-0000fc0f>
    Trying to free nonexistent resource <20000000-200003ff>
    hda: IC35L120AVVA07-0, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    hdc: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
    ide1 at 0x170-0x177,0x376 on irq 15
    Unable to handle kernel NULL pointer dereference at virtual address 00000000
    printing eip:
    c01d7796
    *pde = 00000000
    Oops: 0000
    CPU: 0
    EIP: 0010:[<c01d7796>] Not tainted
    EFLAGS: 00010282
    eax: c16de580 ebx: 00000000 ecx: 00000000 edx: 00000000
    esi: c0399a50 edi: c0105000 ebp: dffebf7c esp: dffebf68
    ds: 0018 es: 0018 ss: 0018
    Process swapper (pid: 1, stackpage=dffeb000)
    Stack: c02d4de8 00000000 c16ec800 c0397260 c0399a50 dffebf84 c0332a72 dffebfa0
    c0332aaf dffee700 c02bc5ce 00000000 c03671e4 00000000 dffebfc0 c0330e93
    c0394520 00000000 000003fc 00022000 00000000 00000000 dffebfc8 c0330eb8
    Call Trace: [<c0105045>] [<c0105000>] [<c010579e>] [<c0105030>]

    Code: 8b 13 85 d2 74 bf 80 7b 04 00 74 b9 8b 73 08 85 f6 74 b2 8d
    <0>Kernel panic: Attempted to kill init!

    ---

    which `ksymoops -m System.map -v vmlinux -K -O -L < /tmp/24` gives:

    ksymoops 2.3.7 on i686 2.4.20-pre1-ac1. Options used
    -v vmlinux (specified)
    -K (specified)
    -L (specified)
    -O (specified)
    -m System.map (specified)

    CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 16
    cpu: 0, clocks: 1009468, slice: 504734
    Unable to handle kernel NULL pointer dereference at virtual address 00000000
    c01d7796
    *pde = 00000000
    Oops: 0000
    CPU: 0
    EIP: 0010:[<c01d7796>] Not tainted
    Using defaults from ksymoops -t elf32-i386 -a i386
    EFLAGS: 00010282
    eax: c16de580 ebx: 00000000 ecx: 00000000 edx: 00000000
    esi: c0399a50 edi: c0105000 ebp: dffebf7c esp: dffebf68
    ds: 0018 es: 0018 ss: 0018
    Process swapper (pid: 1, stackpage=dffeb000)
    Stack: c02d4de8 00000000 c16ec800 c0397260 c0399a50 dffebf84 c0332a72 dffebfa0
    c0332aaf dffee700 c02bc5ce 00000000 c03671e4 00000000 dffebfc0 c0330e93
    c0394520 00000000 000003fc 00022000 00000000 00000000 dffebfc8 c0330eb8
    Call Trace: [<c0105045>] [<c0105000>] [<c010579e>] [<c0105030>]
    Code: 8b 13 85 d2 74 bf 80 7b 04 00 74 b9 8b 73 08 85 f6 74 b2 8d

    >>EIP; c01d7796 <proc_ide_create+66/e0> <=====
    Trace; c0105045 <init+15/140>
    Trace; c0105000 <_stext+0/0>
    Trace; c010579e <kernel_thread+2e/40>
    Trace; c0105030 <init+0/140>
    Code; c01d7796 <proc_ide_create+66/e0>
    00000000 <_EIP>:
    Code; c01d7796 <proc_ide_create+66/e0> <=====
    0: 8b 13 mov (%ebx),%edx <=====
    Code; c01d7798 <proc_ide_create+68/e0>
    2: 85 d2 test %edx,%edx
    Code; c01d779a <proc_ide_create+6a/e0>
    4: 74 bf je ffffffc5 <_EIP+0xffffffc5> c01d775b <proc_ide_create+2b/e0>
    Code; c01d779c <proc_ide_create+6c/e0>
    6: 80 7b 04 00 cmpb $0x0,0x4(%ebx)
    Code; c01d77a0 <proc_ide_create+70/e0>
    a: 74 b9 je ffffffc5 <_EIP+0xffffffc5> c01d775b <proc_ide_create+2b/e0>
    Code; c01d77a2 <proc_ide_create+72/e0>
    c: 8b 73 08 mov 0x8(%ebx),%esi
    Code; c01d77a5 <proc_ide_create+75/e0>
    f: 85 f6 test %esi,%esi
    Code; c01d77a7 <proc_ide_create+77/e0>
    11: 74 b2 je ffffffc5 <_EIP+0xffffffc5> c01d775b <proc_ide_create+2b/e0>
    Code; c01d77a9 <proc_ide_create+79/e0>
    13: 8d 00 lea (%eax),%eax

    <0>Kernel panic: Attempted to kill init!

    ---

    And from scripts/ver_linux:

    Gnu C gcc-3.2 (GCC) 3.2 (Mandrake Linux 9.0 3.2-0.3mdk) Copyright (C) 2002 Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
    Gnu make 3.79.1
    util-linux 2.11t
    mount 2.11t
    modutils 2.4.19
    e2fsprogs 1.27
    PPP 2.4.1
    isdn4k-utils 3.1pre1
    Linux C Library 2.2.5
    Dynamic linker (ldd) 2.2.5
    Procps 2.0.7
    Net-tools 1.60
    Console-tools 0.2.3
    Sh-utils 2.0.15

    ---

    Should I sent other tings?

    Thank you very much,

    Greg
    ________________________________________________________________
    http://ulima.unil.ch/greg ICQ:16624071 mailto:greg@ulima.unil.ch
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:28    [W:0.035 / U:59.520 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site