lkml.org 
[lkml]   [2002]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: PDC20267 + RAID can't find raid device
    >   Are you sure you have the raid array configured in the fasttrak bios? 
    > I don't think enabling brust should matter. It's working for me:

    Actually, I don't know, but it says it's there according to it's bios.

    > Uniform Multi-Platform E-IDE driver Revision: 6.31
    > ide: Assuming 33MHz system bus speed for PIO modes; override with
    > idebus=xx
    > PDC20267: IDE controller on PCI bus 00 dev 18
    > PDC20267: chipset revision 2
    > PDC20267: not 100% native mode: will probe irqs later
    > PDC20267: ROM enabled at 0xfeae0000
    > PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
    > Mode.
    > ide2: BM-DMA at 0xdf00-0xdf07, BIOS settings: hde:pio, hdf:pio
    > ide3: BM-DMA at 0xdf08-0xdf0f, BIOS settings: hdg:pio, hdh:pio
    > SvrWks OSB4: IDE controller on PCI bus 00 dev 79
    > SvrWks OSB4: chipset revision 0
    > SvrWks OSB4: not 100% native mode: will probe irqs later
    > ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
    > ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
    > hde: ST320410A, ATA DISK drive
    > hdg: ST320410A, ATA DISK drive
    > ide2 at 0xdfe0-0xdfe7,0xdfae on irq 31
    > ide3 at 0xdfa0-0xdfa7,0xdfaa on irq 31
    > hde: host protected area => 1
    > hde: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63,
    > UDMA(100)
    > hdg: host protected area => 1
    > hdg: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63,
    > UDMA(100)
    > ide-floppy driver 0.99.newide
    > Partition check:
    > hde: [PTBL] [2434/255/63] hde1 hde2 hde3
    > hdg: [PTBL] [2434/255/63] hdg1 hdg2 hdg3
    > Floppy drive(s): fd0 is 1.44M
    > Partition check:
    > hde: [PTBL] [2434/255/63] hde1 hde2 hde3
    > hdg: [PTBL] [2434/255/63] hdg1 hdg2 hdg3
    > ...
    > ataraid/d0: ataraid/d0p1 ataraid/d0p2 ataraid/d0p3
    > Drive 0 is 19092 Mb (33 / 0)
    > Drive 1 is 19092 Mb (34 / 0)
    > Raid1 array consists of 2 drives.
    > Promise Fasttrak(tm) Softwareraid driver for linux version 0.03beta
    > Highpoint HPT370 Softwareraid driver for linux version 0.01
    > No raid array found
    >
    > On Thu, 2002-06-06 at 12:20, William Thompson wrote:
    > > > It works for me once I got the right options. Did you enable the
    > > > "fasttrak feature"
    > > >
    > > > I'm using the following options in my .config:
    > > > CONFIG_BLK_DEV_PDC202XX=y
    > > > CONFIG_PDC202XX_BURST=y
    > > > CONFIG_PDC202XX_FORCE=y
    > > > CONFIG_BLK_DEV_ATARAID_PDC=y
    > >
    > > Only difference is the fact I didn't enable BURST. your other 3 options are
    > > the same as mine.
    > >
    > > The thing says:
    > > Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
    > >
    > > > /dev/ataraid/d0 devices, and the /dev/hd devices. This makes for lots
    > > > of fun in the Red Hat installer, and Cerberus.
    > >
    > > I'm using debian, but I'm not actually installing the system, I'm copying
    > > from another.
    > >
    > > > > After trying 2.4.19-pre10-ac2 I can finally use the PDC20267 controller,
    > > > > however, it doesn't find any raid devices.
    > > > >
    > > > > I have 2 quantum fireballlct10 05 on the controller (hde and hdg) and
    > > > > created a stripe between these 2 disks in the controller's bios.
    > > > >
    > > > > I can see both disks w/o problems.
    > > > >
    > > > > I'd rather not use the linux software raid since you can't partition it.
    > > > >
    > > > > IDE, PDC20267, FastTrak, and the raid driver are all compiled into the
    > > > > kernel.
    > > > >
    > > > > More info is available at request.
    > > > > -
    > > > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    > > > > the body of a message to majordomo@vger.kernel.org
    > > > > More majordomo info at http://vger.kernel.org/majordomo-info.html
    > > > > Please read the FAQ at http://www.tux.org/lkml/
    > > > >
    > > >
    > > >
    > > >
    > >
    >
    >
    >
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:26    [W:0.029 / U:240.384 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site