lkml.org 
[lkml]   [2002]   [Jun]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Subject[PROBLEM] sundance on d-link dfe-580tx
From
Date
Hello lkml, jeff and donald,

I have been testing the D-Link DFE-580TX Quad channel server card (4
port nic), on kernel 2.4.18 with little success.

Attached are the appropriate results of dmesg, ifconfig, lspci and
modules.conf; aswell as the results of the pci-testing tool found on
scyld.com, however the card does not support mii testing, claiming to
have no MII transceiver.

Specifically, the sundance module can be modprobe'd, and the interfaces
of the 4port nic (eth2->eth5) can be brought up with ifconfig, and to
all intents and purposes *should* be working, however the results of
`tail dmesg` and `tail messages` show a transmit timeout on all the
nic's interfaces and testing the interfaces with ping returns host
unreachable (only on this card, the onboard nic and single port pci card
both work properly).

I would appreciate being informed if there is a fix in a later
version,or if any more debugging information is required I would be
happy to oblige.

Matthew Hall

--
Matthew Hall -- matt@ecsc.co.uk -- http://people.ecsc.co.uk/~matt/
Sig: When I was a boy I was told that anybody could become President. Now I'm
beginning to believe it. - Clarence Darrow
eth0 Link encap:Ethernet HWaddr 00:C0:9F:05:B5:75
inet addr:192.168.0.153 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:253 errors:0 dropped:0 overruns:0 frame:0
TX packets:102 errors:0 dropped:0 overruns:4 carrier:0
collisions:0 txqueuelen:100
RX bytes:31707 (30.9 Kb) TX bytes:15077 (14.7 Kb)
Interrupt:20 Base address:0xd000

eth1 Link encap:Ethernet HWaddr 00:02:B3:9E:62:D6
inet addr:192.168.0.152 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:12 carrier:0
collisions:0 txqueuelen:100
RX bytes:632 (632.0 b) TX bytes:1064 (1.0 Kb)
Interrupt:30 Base address:0xf000

eth2 Link encap:Ethernet HWaddr FE:AB:FE:AB:FE:AB
inet addr:192.168.0.151 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7434240 errors:0 dropped:28919 overruns:0 frame:0
TX packets:7908923 errors:10 dropped:0 overruns:0 carrier:0
collisions:58080 txqueuelen:100
RX bytes:1886929406 (1799.5 Mb) TX bytes:1886957115 (1799.5 Mb)
Interrupt:28 Base address:0x5000

eth3 Link encap:Ethernet HWaddr FE:AB:FE:AB:FE:AB
inet addr:192.168.0.150 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7188480 errors:0 dropped:27963 overruns:0 frame:0
TX packets:7647471 errors:0 dropped:0 overruns:0 carrier:0
collisions:56160 txqueuelen:100
RX bytes:2960410694 (2823.2 Mb) TX bytes:2960437487 (2823.2 Mb)
Interrupt:29 Base address:0x7000

eth4 Link encap:Ethernet HWaddr FE:AB:FE:AB:FE:AB
inet addr:192.168.0.149 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7188480 errors:0 dropped:27963 overruns:0 frame:0
TX packets:7647471 errors:0 dropped:0 overruns:0 carrier:0
collisions:56160 txqueuelen:100
RX bytes:2960410694 (2823.2 Mb) TX bytes:2960437487 (2823.2 Mb)
Interrupt:28 Base address:0x9000

eth5 Link encap:Ethernet HWaddr FE:AB:FE:AB:FE:AB
inet addr:192.168.0.148 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7188480 errors:0 dropped:27963 overruns:0 frame:0
TX packets:7647471 errors:0 dropped:0 overruns:0 carrier:0
collisions:56160 txqueuelen:100
RX bytes:2960410694 (2823.2 Mb) TX bytes:2960437487 (2823.2 Mb)
Interrupt:29 Base address:0xb000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:410 errors:0 dropped:0 overruns:0 frame:0
TX packets:410 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:49480 (48.3 Kb) TX bytes:49480 (48.3 Kb)

00:00.0 Host bridge: ServerWorks CNB20LE Host Bridge (rev 06)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 48, cache line size 08

00:00.1 Host bridge: ServerWorks CNB20LE Host Bridge (rev 06)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 48, cache line size 08

00:02.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
Subsystem: Dell Computer Corporation: Unknown device 010b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe123000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at dcc0 [size=64]
Region 2: Memory at fe000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fd000000-fdffffff
Prefetchable memory behind bridge: 00000000fa000000-00000000faf00000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
00:0a.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 0d)
Subsystem: Intel Corporation: Unknown device 1050
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 30
Region 0: Memory at fe122000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at dc80 [size=64]
Region 2: Memory at fe100000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0b.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 010b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at fe121000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 ISA bridge: ServerWorks CSB5 South Bridge (rev 92)
Subsystem: ServerWorks CSB5 South Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32

00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 92) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Computer Corporation: Unknown device c10b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at 08b0 [size=16]
Region 5: I/O ports at 08c0 [size=4]

00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 05) (prog-if 10 [OHCI])
Subsystem: ServerWorks OSB4/CSB5 OHCI USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fe120000 (32-bit, non-prefetchable) [size=4K]
00:0f.3 Host bridge: ServerWorks: Unknown device 0230
Subsystem: ServerWorks: Unknown device 0230
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0

01:04.0 Ethernet controller: D-Link System Inc: Unknown device 1002 (rev 12)
Subsystem: D-Link System Inc: Unknown device 1012
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at ec80 [size=128]
Expansion ROM at fd000000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
01:05.0 Ethernet controller: D-Link System Inc: Unknown device 1002 (rev 12)
Subsystem: D-Link System Inc: Unknown device 1012
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 29
Region 0: I/O ports at ec00 [size=128]
Expansion ROM at fd000000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
01:06.0 Ethernet controller: D-Link System Inc: Unknown device 1002 (rev 12)
Subsystem: D-Link System Inc: Unknown device 1012
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at e880 [size=128]
Expansion ROM at fd000000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
01:07.0 Ethernet controller: D-Link System Inc: Unknown device 1002 (rev 12)
Subsystem: D-Link System Inc: Unknown device 1012
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 29
Region 0: I/O ports at e800 [size=128]
Expansion ROM at fd000000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
alias parport_lowlevel parport_pc
alias eth0 eepro100
alias eth1 eepro100
alias eth2 sundance
alias eth3 sundance
alias eth4 sundance
alias eth5 sundance
pci-config.c:v2.02 1/8/2001 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Device #1 at bus 0 device/function 0/0, 00091166.
Device #2 at bus 0 device/function 0/1, 00091166.
Device #3 at bus 0 device/function 2/0, 12298086.
Device #4 at bus 0 device/function 9/0, 00241011.
Device #5 at bus 0 device/function 10/0, 12298086.
Device #6 at bus 0 device/function 11/0, 47521002.
Device #7 at bus 0 device/function 15/0, 02011166.
Device #8 at bus 0 device/function 15/1, 02121166.
Device #9 at bus 0 device/function 15/2, 02201166.
Device #10 at bus 0 device/function 15/3, 02301166.
eth2: D-Link DFE-580TX 4 port Server Adapter at 0xc8cbb000, fe:ab:fe:ab:fe:ab, IRQ 29.
eth2: No MII transceiver found!, ASIC status 7fabfe
Override speed=100, Full duplex

NETDEV WATCHDOG: eth2: transmit timed out
eth2: Transmit timed out, status 00, resetting...
Rx ring c53bd000: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tx ring c5384000: 80008001 80008005 80008009 8000800d 80008011 80008015 80008019 8000801d 80008021 0000 0000 0000 0000 0000 0000 0000
\
 
 \ /
  Last update: 2005-03-22 13:26    [from the cache]
©2003-2011 Jasper Spaans