lkml.org 
[lkml]   [2002]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH] 2.5.15 IDE 61
Sat May 11 18:45:08 CEST 2002 ide-clean-61

- Fix typo in pdc202xx driver.

- Fix locking order in ioctl.

- Fix wrong time_after usage introduced in 60. Maybe the fact I always get is
wrong is related to the fact that I'm using the mouse with the left hand!?

- Apply arch-clean-2 by Bartlomiej Zolnierkiewicz.

- Don't disable interrupts during ide_wait_stat(). I see no reason too.

- Push flags down from hwgroup to the ata_chaannel structure.

- Apply small fixes from Franz Sirl to make AEC6280 working properly again.

diff -urN linux-2.5.15/drivers/ide/ide.c linux/drivers/ide/ide.c
--- linux-2.5.15/drivers/ide/ide.c 2002-05-13 12:44:17.000000000 +0200
+++ linux/drivers/ide/ide.c 2002-05-13 02:13:30.000000000 +0200
@@ -317,7 +317,7 @@
blkdev_dequeue_request(rq);
else
blk_queue_end_tag(&drive->queue, rq);
- HWGROUP(drive)->rq = NULL;
+ drive->rq = NULL;
end_that_request_last(rq);
ret = 0;
}
@@ -635,7 +635,7 @@
}

blkdev_dequeue_request(rq);
- HWGROUP(drive)->rq = NULL;
+ drive->rq = NULL;
end_that_request_last(rq);
}

@@ -886,7 +886,6 @@
{
u8 stat;
int i;
- unsigned long flags;

/* bail early if we've exceeded max_failures */
if (drive->max_failures && (drive->failures > drive->max_failures)) {
@@ -896,24 +895,20 @@

udelay(1); /* spec allows drive 400ns to assert "BUSY" */
if ((stat = GET_STAT()) & BUSY_STAT) {
- __save_flags(flags); /* local CPU only */
- ide__sti(); /* local CPU only */
timeout += jiffies;
while ((stat = GET_STAT()) & BUSY_STAT) {
- if (time_after(timeout, jiffies)) {
- __restore_flags(flags); /* local CPU only */
+ if (time_after(jiffies, timeout)) {
*startstop = ide_error(drive, rq, "status timeout", stat);
return 1;
}
}
- __restore_flags(flags); /* local CPU only */
}
+
/*
- * Allow status to settle, then read it again.
- * A few rare drives vastly violate the 400ns spec here,
- * so we'll wait up to 10usec for a "good" status
- * rather than expensively fail things immediately.
- * This fix courtesy of Matthew Faupel & Niccolo Rigacci.
+ * Allow status to settle, then read it again. A few rare drives
+ * vastly violate the 400ns spec here, so we'll wait up to 10usec for a
+ * "good" status rather than expensively fail things immediately. This
+ * fix courtesy of Matthew Faupel & Niccolo Rigacci.
*/
for (i = 0; i < 10; i++) {
udelay(1);
@@ -1074,15 +1069,13 @@
struct ata_channel *ch = drive->channel;
ide_hwgroup_t *hwgroup = ch->hwgroup;
unsigned long flags;
- struct request *rq;

spin_lock_irqsave(&ide_lock, flags);
hwgroup->handler = NULL;
del_timer(&ch->timer);
- rq = hwgroup->rq;
spin_unlock_irqrestore(&ide_lock, flags);

- return start_request(drive, rq);
+ return start_request(drive, drive->rq);
}

/*
@@ -1180,7 +1173,6 @@
if (choice)
return choice;

- channel->hwgroup->rq = NULL;
sleep = longest_sleep(channel);

if (sleep) {
@@ -1197,14 +1189,14 @@
if (timer_pending(&channel->timer))
printk(KERN_ERR "ide_set_handler: timer already active\n");
#endif
- set_bit(IDE_SLEEP, &channel->hwgroup->flags);
+ set_bit(IDE_SLEEP, &channel->active);
mod_timer(&channel->timer, sleep);
/* we purposely leave hwgroup busy while sleeping */
} else {
/* Ugly, but how can we sleep for the lock otherwise? perhaps
* from tq_disk? */
ide_release_lock(&irq_lock);/* for atari only */
- clear_bit(IDE_BUSY, &channel->hwgroup->flags);
+ clear_bit(IDE_BUSY, &channel->active);
}

return NULL;
@@ -1217,13 +1209,13 @@
*/
static void queue_commands(struct ata_device *drive, int masked_irq)
{
- ide_hwgroup_t *hwgroup = drive->channel->hwgroup;
+ struct ata_channel *ch = drive->channel;
ide_startstop_t startstop = -1;

for (;;) {
struct request *rq = NULL;

- if (!test_bit(IDE_BUSY, &hwgroup->flags))
+ if (!test_bit(IDE_BUSY, &ch->active))
printk(KERN_ERR"%s: error: not busy while queueing!\n", drive->name);

/* Abort early if we can't queue another command. for non
@@ -1232,13 +1224,13 @@
*/
if (!ata_can_queue(drive)) {
if (!ata_pending_commands(drive))
- clear_bit(IDE_BUSY, &hwgroup->flags);
+ clear_bit(IDE_BUSY, &ch->active);
break;
}

drive->sleep = 0;

- if (test_bit(IDE_DMA, &hwgroup->flags)) {
+ if (test_bit(IDE_DMA, &ch->active)) {
printk("ide_do_request: DMA in progress...\n");
break;
}
@@ -1256,8 +1248,8 @@

if (!(rq = elv_next_request(&drive->queue))) {
if (!ata_pending_commands(drive))
- clear_bit(IDE_BUSY, &hwgroup->flags);
- hwgroup->rq = NULL;
+ clear_bit(IDE_BUSY, &ch->active);
+ drive->rq = NULL;
break;
}

@@ -1268,7 +1260,7 @@
if (!(rq->flags & REQ_CMD) && ata_pending_commands(drive))
break;

- hwgroup->rq = rq;
+ drive->rq = rq;

/* Some systems have trouble with IDE IRQs arriving while the
* driver is still setting things up. So, here we disable the
@@ -1339,12 +1331,10 @@
*/
static void ide_do_request(struct ata_channel *channel, int masked_irq)
{
- ide_hwgroup_t *hwgroup = channel->hwgroup;
-
ide_get_lock(&irq_lock, ata_irq_request, hwgroup);/* for atari only: POSSIBLY BROKEN HERE(?) */
__cli(); /* necessary paranoia: ensure IRQs are masked on local CPU */

- while (!test_and_set_bit(IDE_BUSY, &hwgroup->flags)) {
+ while (!test_and_set_bit(IDE_BUSY, &channel->active)) {
struct ata_channel *ch;
struct ata_device *drive;

@@ -1405,7 +1395,7 @@
* un-busy drive etc (hwgroup->busy is cleared on return) and
* make sure request is sane
*/
- HWGROUP(drive)->rq = NULL;
+ drive->rq = NULL;

rq->errors = 0;
if (rq->bio) {
@@ -1446,8 +1436,8 @@
* complain about anything.
*/

- if (test_and_clear_bit(IDE_SLEEP, &hwgroup->flags))
- clear_bit(IDE_BUSY, &hwgroup->flags);
+ if (test_and_clear_bit(IDE_SLEEP, &ch->active))
+ clear_bit(IDE_BUSY, &ch->active);
} else {
struct ata_device *drive = ch->drive;
if (!drive) {
@@ -1457,11 +1447,11 @@
ide_startstop_t startstop;

/* paranoia */
- if (!test_and_set_bit(IDE_BUSY, &hwgroup->flags))
+ if (!test_and_set_bit(IDE_BUSY, &ch->active))
printk("%s: ide_timer_expiry: hwgroup was not busy??\n", drive->name);
if ((expiry = ch->expiry) != NULL) {
/* continue */
- if ((wait = expiry(drive, HWGROUP(drive)->rq)) != 0) {
+ if ((wait = expiry(drive, drive->rq)) != 0) {
/* reengage timer */
ch->timer.expires = jiffies + wait;
add_timer(&ch->timer);
@@ -1484,25 +1474,25 @@
#endif
__cli(); /* local CPU only, as if we were handling an interrupt */
if (ch->poll_timeout != 0) {
- startstop = handler(drive, ch->hwgroup->rq);
+ startstop = handler(drive, drive->rq);
} else if (drive_is_ready(drive)) {
if (drive->waiting_for_dma)
udma_irq_lost(drive);
(void) ide_ack_intr(ch);
printk("%s: lost interrupt\n", drive->name);
- startstop = handler(drive, ch->hwgroup->rq);
+ startstop = handler(drive, drive->rq);
} else {
if (drive->waiting_for_dma) {
startstop = ide_stopped;
- dma_timeout_retry(drive, ch->hwgroup->rq);
+ dma_timeout_retry(drive, drive->rq);
} else
- startstop = ide_error(drive, ch->hwgroup->rq, "irq timeout", GET_STAT());
+ startstop = ide_error(drive, drive->rq, "irq timeout", GET_STAT());
}
set_recovery_timer(ch);
enable_irq(ch->irq);
spin_lock_irq(&ide_lock);
if (startstop == ide_stopped)
- clear_bit(IDE_BUSY, &hwgroup->flags);
+ clear_bit(IDE_BUSY, &ch->active);
}
}

@@ -1627,7 +1617,7 @@
goto out_lock;
}
/* paranoia */
- if (!test_and_set_bit(IDE_BUSY, &hwgroup->flags))
+ if (!test_and_set_bit(IDE_BUSY, &ch->active))
printk(KERN_ERR "%s: %s: hwgroup was not busy!?\n", drive->name, __FUNCTION__);
hwgroup->handler = NULL;
del_timer(&ch->timer);
@@ -1637,7 +1627,7 @@
ide__sti(); /* local CPU only */

/* service this interrupt, may set handler for next interrupt */
- startstop = handler(drive, hwgroup->rq);
+ startstop = handler(drive, drive->rq);
spin_lock_irq(&ide_lock);

/*
@@ -1650,7 +1640,7 @@
set_recovery_timer(drive->channel);
if (startstop == ide_stopped) {
if (hwgroup->handler == NULL) { /* paranoia */
- clear_bit(IDE_BUSY, &hwgroup->flags);
+ clear_bit(IDE_BUSY, &ch->active);
ide_do_request(ch, ch->irq);
} else {
printk("%s: %s: huh? expected NULL handler on exit\n", drive->name, __FUNCTION__);
@@ -1738,7 +1728,7 @@
spin_lock_irqsave(&ide_lock, flags);
if (blk_queue_empty(&drive->queue) || action == ide_preempt) {
if (action == ide_preempt)
- HWGROUP(drive)->rq = NULL;
+ drive->rq = NULL;
} else {
if (action == ide_wait || action == ide_end)
queue_head = queue_head->prev;
@@ -2222,8 +2212,6 @@

int ide_spin_wait_hwgroup(struct ata_device *drive)
{
- ide_hwgroup_t *hwgroup = HWGROUP(drive);
-
/* FIXME: Wait on a proper timer. Instead of playing games on the
* spin_lock().
*/
@@ -2232,7 +2220,7 @@

spin_lock_irq(&ide_lock);

- while (test_bit(IDE_BUSY, &hwgroup->flags)) {
+ while (test_bit(IDE_BUSY, &drive->channel->active)) {
spin_unlock_irq(&ide_lock);
if (time_after(jiffies, timeout)) {
printk("%s: channel busy\n", drive->name);
@@ -2316,7 +2304,9 @@
kdev_t dev;

dev = inode->i_rdev;
- major = major(dev); minor = minor(dev);
+ major = major(dev);
+ minor = minor(dev);
+
if ((drive = get_info_ptr(inode->i_rdev)) == NULL)
return -ENODEV;

@@ -2376,6 +2366,7 @@

if (put_user(val, (unsigned long *) arg))
return -EFAULT;
+
return 0;
}

@@ -2384,12 +2375,12 @@
if (arg < 0 || arg > 1)
return -EINVAL;

- if (ide_spin_wait_hwgroup(drive))
- return -EBUSY;
-
if (drive->channel->no_unmask)
return -EIO;

+ if (ide_spin_wait_hwgroup(drive))
+ return -EBUSY;
+
drive->channel->unmask = arg;
spin_unlock_irq(&ide_lock);

@@ -2426,11 +2417,20 @@

if (!loc || (drive->type != ATA_DISK && drive->type != ATA_FLOPPY))
return -EINVAL;
- if (put_user(drive->bios_head, (byte *) &loc->heads)) return -EFAULT;
- if (put_user(drive->bios_sect, (byte *) &loc->sectors)) return -EFAULT;
- if (put_user(bios_cyl, (unsigned short *) &loc->cylinders)) return -EFAULT;
+
+ if (put_user(drive->bios_head, (byte *) &loc->heads))
+ return -EFAULT;
+
+ if (put_user(drive->bios_sect, (byte *) &loc->sectors))
+ return -EFAULT;
+
+ if (put_user(bios_cyl, (unsigned short *) &loc->cylinders))
+ return -EFAULT;
+
if (put_user((unsigned)drive->part[minor(inode->i_rdev)&PARTN_MASK].start_sect,
- (unsigned long *) &loc->start)) return -EFAULT;
+ (unsigned long *) &loc->start))
+ return -EFAULT;
+
return 0;
}

@@ -2440,48 +2440,59 @@
if (!loc || (drive->type != ATA_DISK && drive->type != ATA_FLOPPY))
return -EINVAL;

- if (put_user(drive->head, (u8 *) &loc->heads)) return -EFAULT;
- if (put_user(drive->sect, (u8 *) &loc->sectors)) return -EFAULT;
- if (put_user(drive->cyl, (unsigned int *) &loc->cylinders)) return -EFAULT;
+ if (put_user(drive->head, (u8 *) &loc->heads))
+ return -EFAULT;
+
+ if (put_user(drive->sect, (u8 *) &loc->sectors))
+ return -EFAULT;
+
+ if (put_user(drive->cyl, (unsigned int *) &loc->cylinders))
+ return -EFAULT;
+
if (put_user((unsigned)drive->part[minor(inode->i_rdev)&PARTN_MASK].start_sect,
- (unsigned long *) &loc->start)) return -EFAULT;
+ (unsigned long *) &loc->start))
+ return -EFAULT;
+
return 0;
}

case BLKRRPART: /* Re-read partition tables */
- if (!capable(CAP_SYS_ADMIN))
- return -EACCES;
return ide_revalidate_disk(inode->i_rdev);

case HDIO_GET_IDENTITY:
if (minor(inode->i_rdev) & PARTN_MASK)
return -EINVAL;
+
if (drive->id == NULL)
return -ENOMSG;
+
if (copy_to_user((char *)arg, (char *)drive->id, sizeof(*drive->id)))
return -EFAULT;
+
return 0;

case HDIO_GET_NICE:
- return put_user(drive->dsc_overlap << IDE_NICE_DSC_OVERLAP |
- drive->atapi_overlap << IDE_NICE_ATAPI_OVERLAP,
+ return put_user(drive->dsc_overlap << IDE_NICE_DSC_OVERLAP |
+ drive->atapi_overlap << IDE_NICE_ATAPI_OVERLAP,
(long *) arg);

case HDIO_DRIVE_CMD:
- if (!capable(CAP_SYS_ADMIN) || !capable(CAP_SYS_RAWIO))
+ if (!capable(CAP_SYS_RAWIO))
return -EACCES;
+
return ide_cmd_ioctl(drive, arg);

case HDIO_SET_NICE:
- if (!capable(CAP_SYS_ADMIN)) return -EACCES;
if (arg != (arg & ((1 << IDE_NICE_DSC_OVERLAP))))
return -EPERM;
+
drive->dsc_overlap = (arg >> IDE_NICE_DSC_OVERLAP) & 1;
/* Only CD-ROM's and tapes support DSC overlap. */
if (drive->dsc_overlap && !(drive->type == ATA_ROM || drive->type == ATA_TAPE)) {
drive->dsc_overlap = 0;
return -EPERM;
}
+
return 0;

case BLKGETSIZE:
@@ -2505,25 +2516,24 @@
return block_ioctl(inode->i_bdev, cmd, arg);

case HDIO_GET_BUSSTATE:
- if (!capable(CAP_SYS_ADMIN))
- return -EACCES;
if (put_user(drive->channel->bus_state, (long *)arg))
return -EFAULT;
+
return 0;

case HDIO_SET_BUSSTATE:
- if (!capable(CAP_SYS_ADMIN))
- return -EACCES;
if (drive->channel->busproc)
drive->channel->busproc(drive, (int)arg);
+
return 0;

- /* Now check whatever this particular ioctl has a special
- * implementation.
+ /* Now check whatever this particular ioctl has a device type
+ * specific implementation.
*/
default:
if (ata_ops(drive) && ata_ops(drive)->ioctl)
return ata_ops(drive)->ioctl(drive, inode, file, cmd, arg);
+
return -EINVAL;
}
}
@@ -2545,6 +2555,7 @@
res = 1; /* assume it was changed */
ata_put(ata_ops(drive));
}
+
return res;
}

diff -urN linux-2.5.15/drivers/ide/ide-disk.c linux/drivers/ide/ide-disk.c
--- linux-2.5.15/drivers/ide/ide-disk.c 2002-05-13 12:44:17.000000000 +0200
+++ linux/drivers/ide/ide-disk.c 2002-05-12 16:12:30.000000000 +0200
@@ -1058,6 +1058,7 @@

if (put_user(val, (unsigned long *) arg))
return -EFAULT;
+
return 0;
}

@@ -1081,6 +1082,7 @@

if (put_user(val, (unsigned long *) arg))
return -EFAULT;
+
return 0;
}

@@ -1100,7 +1102,7 @@
}

case HDIO_GET_ACOUSTIC: {
- u8 val = drive->acoustic;
+ unsigned long val = drive->acoustic;

if (put_user(val, (u8 *) arg))
return -EFAULT;
@@ -1128,6 +1130,7 @@

if (put_user(val, (u8 *) arg))
return -EFAULT;
+
return 0;
}

@@ -1153,7 +1156,7 @@


/*
- * IDE subdriver functions, registered with ide.c
+ * Subdriver functions.
*/
static struct ata_operations idedisk_driver = {
owner: THIS_MODULE,
@@ -1178,11 +1181,9 @@

while ((drive = ide_scan_devices(ATA_DISK, "ide-disk", &idedisk_driver, failed)) != NULL) {
if (idedisk_cleanup (drive)) {
- printk (KERN_ERR "%s: cleanup_module() called while still busy\n", drive->name);
- failed++;
+ printk(KERN_ERR "%s: cleanup_module() called while still busy\n", drive->name);
+ ++failed;
}
- /* We must remove proc entries defined in this module.
- Otherwise we oops while accessing these entries */
}
}

@@ -1203,10 +1204,11 @@
idedisk_cleanup(drive);
continue;
}
- failed--;
+ --failed;
}
revalidate_drives();
MOD_DEC_USE_COUNT;
+
return 0;
}

diff -urN linux-2.5.15/drivers/ide/ide-dma.c linux/drivers/ide/ide-dma.c
--- linux-2.5.15/drivers/ide/ide-dma.c 2002-05-13 12:44:17.000000000 +0200
+++ linux/drivers/ide/ide-dma.c 2002-05-11 23:23:14.000000000 +0200
@@ -382,10 +382,10 @@

#ifdef DEBUG
printk("%s: dma_timer_expiry: dma status == 0x%02x\n", drive->name, dma_stat);
-#endif /* DEBUG */
+#endif

#if 0
- HWGROUP(drive)->expiry = NULL; /* one free ride for now */
+ drive->expiry = NULL; /* one free ride for now */
#endif

if (dma_stat & 2) { /* ERROR */
diff -urN linux-2.5.15/drivers/ide/ide-pci.c linux/drivers/ide/ide-pci.c
--- linux-2.5.15/drivers/ide/ide-pci.c 2002-05-10 00:25:29.000000000 +0200
+++ linux/drivers/ide/ide-pci.c 2002-05-13 12:37:07.000000000 +0200
@@ -122,7 +122,7 @@
* Unless there is a bootable card that does not use the standard
* ports 1f0/170 (the ide0/ide1 defaults). The (bootable) flag.
*/
- if (bootable) {
+ if (bootable == ON_BOARD) {
for (h = 0; h < MAX_HWIFS; ++h) {
hwif = &ide_hwifs[h];
if (hwif->chipset == ide_unknown)
@@ -703,7 +703,7 @@
hpt374_device_order_fixup(dev, d);
} else if (d->vendor == PCI_VENDOR_ID_PROMISE && d->device == PCI_DEVICE_ID_PROMISE_20268R)
pdc20270_device_order_fixup(dev, d);
- else if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
+ else {
printk(KERN_INFO "ATA: %s (%04x:%04x) on PCI slot %s\n",
dev->name, vendor, device, dev->slot_name);
setup_pci_device(dev, d);
diff -urN linux-2.5.15/drivers/ide/ide-taskfile.c linux/drivers/ide/ide-taskfile.c
--- linux-2.5.15/drivers/ide/ide-taskfile.c 2002-05-13 12:44:17.000000000 +0200
+++ linux/drivers/ide/ide-taskfile.c 2002-05-12 17:47:58.000000000 +0200
@@ -279,6 +279,7 @@

if (stat & BUSY_STAT)
return 0; /* drive busy: definitely not interrupting */
+
return 1; /* drive ready: *might* be interrupting */
}

diff -urN linux-2.5.15/drivers/ide/pdc202xx.c linux/drivers/ide/pdc202xx.c
--- linux-2.5.15/drivers/ide/pdc202xx.c 2002-05-10 00:25:39.000000000 +0200
+++ linux/drivers/ide/pdc202xx.c 2002-05-12 16:16:37.000000000 +0200
@@ -1450,7 +1450,7 @@
init_chipset: pdc202xx_init_chipset,
ata66_check: ata66_pdc202xx,
init_channel: ide_init_pdc202xx,
- exnablebits: {{0x50,0x02,0x02}, {0x50,0x04,0x04}},
+ enablebits: {{0x50,0x02,0x02}, {0x50,0x04,0x04}},
bootable: OFF_BOARD,
extra: 48,
flags: ATA_F_IRQ | ATA_F_DMA
diff -urN linux-2.5.15/drivers/ide/sl82c105.c linux/drivers/ide/sl82c105.c
--- linux-2.5.15/drivers/ide/sl82c105.c 2002-05-10 00:23:12.000000000 +0200
+++ linux/drivers/ide/sl82c105.c 2002-05-12 03:35:22.000000000 +0200
@@ -76,7 +76,7 @@
if (ide_config_drive_speed(drive, xfer_mode) == 0)
drv_ctrl = get_timing_sl82c105(t);

- if (drive->using_dma == 0) {
+ if (!drive->using_dma) {
/*
* If we are actually using MW DMA, then we can not
* reprogram the interface drive control register.
diff -urN linux-2.5.15/drivers/ide/tcq.c linux/drivers/ide/tcq.c
--- linux-2.5.15/drivers/ide/tcq.c 2002-05-13 12:44:17.000000000 +0200
+++ linux/drivers/ide/tcq.c 2002-05-13 02:17:33.000000000 +0200
@@ -95,15 +95,15 @@

del_timer(&ch->timer);

- if (test_bit(IDE_DMA, &hwgroup->flags))
+ if (test_bit(IDE_DMA, &ch->active))
udma_stop(drive);

blk_queue_invalidate_tags(q);

drive->using_tcq = 0;
drive->queue_depth = 1;
- clear_bit(IDE_BUSY, &hwgroup->flags);
- clear_bit(IDE_DMA, &hwgroup->flags);
+ clear_bit(IDE_BUSY, &ch->active);
+ clear_bit(IDE_DMA, &ch->active);
hwgroup->handler = NULL;

/*
@@ -152,6 +152,7 @@
static void ata_tcq_irq_timeout(unsigned long data)
{
struct ata_device *drive = (struct ata_device *) data;
+ struct ata_channel *ch = drive->channel;
ide_hwgroup_t *hwgroup = HWGROUP(drive);
unsigned long flags;

@@ -159,7 +160,7 @@

spin_lock_irqsave(&ide_lock, flags);

- if (test_and_set_bit(IDE_BUSY, &hwgroup->flags))
+ if (test_and_set_bit(IDE_BUSY, &ch->active))
printk(KERN_ERR "ATA: %s: hwgroup not busy\n", __FUNCTION__);
if (hwgroup->handler == NULL)
printk(KERN_ERR "ATA: %s: missing isr!\n", __FUNCTION__);
@@ -170,7 +171,7 @@
* if pending commands, try service before giving up
*/
if (ata_pending_commands(drive) && (GET_STAT() & SERVICE_STAT))
- if (service(drive, hwgroup->rq) == ide_started)
+ if (service(drive, drive->rq) == ide_started)
return;

if (drive)
@@ -241,7 +242,7 @@
* Could be called with IDE_DMA in-progress from invalidate
* handler, refuse to do anything.
*/
- if (test_bit(IDE_DMA, &HWGROUP(drive)->flags))
+ if (test_bit(IDE_DMA, &drive->channel->active))
return ide_stopped;

/*
@@ -283,7 +284,7 @@
* should not happen, a buggy device could introduce loop
*/
if ((feat = GET_FEAT()) & NSEC_REL) {
- HWGROUP(drive)->rq = NULL;
+ drive->rq = NULL;
printk("%s: release in service\n", drive->name);
return ide_stopped;
}
@@ -298,7 +299,7 @@
return ide_stopped;
}

- HWGROUP(drive)->rq = rq;
+ drive->rq = rq;

/*
* we'll start a dma read or write, device will trigger
@@ -529,7 +530,7 @@
struct ata_channel *ch = drive->channel;

TCQ_PRINTK("%s: setting up queued %d\n", __FUNCTION__, rq->tag);
- if (!test_bit(IDE_BUSY, &ch->hwgroup->flags))
+ if (!test_bit(IDE_BUSY, &ch->active))
printk("queued_rw: IDE_BUSY not set\n");

if (tcq_wait_dataphase(drive))
@@ -584,7 +585,7 @@
*/
if ((feat = GET_FEAT()) & NSEC_REL) {
drive->immed_rel++;
- HWGROUP(drive)->rq = NULL;
+ drive->rq = NULL;
set_irq(drive, ide_dmaq_intr);

TCQ_PRINTK("REL in queued_start\n");
diff -urN linux-2.5.15/include/asm-alpha/ide.h linux/include/asm-alpha/ide.h
--- linux-2.5.15/include/asm-alpha/ide.h 2002-05-10 00:23:17.000000000 +0200
+++ linux/include/asm-alpha/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -82,10 +82,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASMalpha_IDE_H */
diff -urN linux-2.5.15/include/asm-arm/ide.h linux/include/asm-arm/ide.h
--- linux-2.5.15/include/asm-arm/ide.h 2002-05-10 00:24:07.000000000 +0200
+++ linux/include/asm-arm/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -21,10 +21,6 @@

#include <asm/arch/ide.h>

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
/*
* We always use the new IDE port registering,
* so these are fixed here.
diff -urN linux-2.5.15/include/asm-cris/ide.h linux/include/asm-cris/ide.h
--- linux-2.5.15/include/asm-cris/ide.h 2002-05-10 00:22:28.000000000 +0200
+++ linux/include/asm-cris/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -96,10 +96,6 @@
#undef SUPPORT_SLOW_DATA_PORTS
#define SUPPORT_SLOW_DATA_PORTS 0

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
/* the drive addressing is done through a controller register on the Etrax CPU */
void OUT_BYTE(unsigned char data, ide_ioreg_t reg);
unsigned char IN_BYTE(ide_ioreg_t reg);
diff -urN linux-2.5.15/include/asm-i386/ide.h linux/include/asm-i386/ide.h
--- linux-2.5.15/include/asm-i386/ide.h 2002-05-10 00:21:52.000000000 +0200
+++ linux/include/asm-i386/ide.h 2002-05-13 03:09:01.000000000 +0200
@@ -86,10 +86,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASMi386_IDE_H */
diff -urN linux-2.5.15/include/asm-ia64/ide.h linux/include/asm-ia64/ide.h
--- linux-2.5.15/include/asm-ia64/ide.h 2002-05-10 00:24:57.000000000 +0200
+++ linux/include/asm-ia64/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -92,10 +92,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASM_IA64_IDE_H */
diff -urN linux-2.5.15/include/asm-m68k/ide.h linux/include/asm-m68k/ide.h
--- linux-2.5.15/include/asm-m68k/ide.h 2002-05-10 00:21:32.000000000 +0200
+++ linux/include/asm-m68k/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -145,10 +145,13 @@

#endif /* CONFIG_ATARI || CONFIG_Q40 */

+#define ATA_ARCH_ACK_INTR
+
+#ifdef CONFIG_ATARI
+#define ATA_ARCH_LOCK

static __inline__ void ide_release_lock (int *ide_lock)
{
-#ifdef CONFIG_ATARI
if (MACH_IS_ATARI) {
if (*ide_lock == 0) {
printk("ide_release_lock: bug\n");
@@ -157,12 +160,10 @@
*ide_lock = 0;
stdma_release();
}
-#endif /* CONFIG_ATARI */
}

static __inline__ void ide_get_lock (int *ide_lock, void (*handler)(int, void *, struct pt_regs *), void *data)
{
-#ifdef CONFIG_ATARI
if (MACH_IS_ATARI) {
if (*ide_lock == 0) {
if (in_interrupt() > 0)
@@ -171,10 +172,8 @@
*ide_lock = 1;
}
}
-#endif /* CONFIG_ATARI */
}
-
-#define ide_ack_intr(hwif) ((hwif)->hw.ack_intr ? (hwif)->hw.ack_intr(hwif) : 1)
+#endif /* CONFIG_ATARI */

/*
* On the Atari, we sometimes can't enable interrupts:
diff -urN linux-2.5.15/include/asm-mips/ide.h linux/include/asm-mips/ide.h
--- linux-2.5.15/include/asm-mips/ide.h 2002-05-10 00:22:38.000000000 +0200
+++ linux/include/asm-mips/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -68,10 +68,6 @@
#undef SUPPORT_VLB_SYNC
#define SUPPORT_VLB_SYNC 0

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASM_IDE_H */
diff -urN linux-2.5.15/include/asm-mips64/ide.h linux/include/asm-mips64/ide.h
--- linux-2.5.15/include/asm-mips64/ide.h 2002-05-10 00:21:32.000000000 +0200
+++ linux/include/asm-mips64/ide.h 2002-05-12 16:28:28.000000000 +0200
@@ -68,10 +68,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASM_IDE_H */
diff -urN linux-2.5.15/include/asm-parisc/ide.h linux/include/asm-parisc/ide.h
--- linux-2.5.15/include/asm-parisc/ide.h 2002-05-10 00:23:34.000000000 +0200
+++ linux/include/asm-parisc/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -81,10 +81,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASMi386_IDE_H */
diff -urN linux-2.5.15/include/asm-ppc/ide.h linux/include/asm-ppc/ide.h
--- linux-2.5.15/include/asm-ppc/ide.h 2002-05-10 00:23:34.000000000 +0200
+++ linux/include/asm-ppc/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -108,12 +108,8 @@
}

#if (defined CONFIG_APUS || defined CONFIG_BLK_DEV_MPC8xx_IDE )
-#define ide_ack_intr(hwif) (hwif->hw.ack_intr ? hwif->hw.ack_intr(hwif) : 1)
-#else
-#define ide_ack_intr(hwif) (1)
+#define ATA_ARCH_ACK_INTR
#endif
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)

#endif /* __KERNEL__ */

diff -urN linux-2.5.15/include/asm-ppc64/ide.h linux/include/asm-ppc64/ide.h
--- linux-2.5.15/include/asm-ppc64/ide.h 2002-05-10 00:24:22.000000000 +0200
+++ linux/include/asm-ppc64/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -50,10 +50,6 @@
{
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASMPPC64_IDE_H */
diff -urN linux-2.5.15/include/asm-s390/ide.h linux/include/asm-s390/ide.h
--- linux-2.5.15/include/asm-s390/ide.h 2002-05-10 00:24:47.000000000 +0200
+++ linux/include/asm-s390/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -18,14 +18,6 @@
#define ide__sti() do {} while (0)

/*
- * The following are not needed for the non-m68k ports
- */
-#define ide_ack_intr(hwif) (1)
-#define ide_fix_driveid(id) do {} while (0)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
-/*
* We always use the new IDE port registering,
* so these are fixed here.
*/
diff -urN linux-2.5.15/include/asm-s390x/ide.h linux/include/asm-s390x/ide.h
--- linux-2.5.15/include/asm-s390x/ide.h 2002-05-10 00:21:33.000000000 +0200
+++ linux/include/asm-s390x/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -17,10 +17,6 @@

#define ide__sti() do {} while (0)

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
/*
* We always use the new IDE port registering,
* so these are fixed here.
diff -urN linux-2.5.15/include/asm-sh/ide.h linux/include/asm-sh/ide.h
--- linux-2.5.15/include/asm-sh/ide.h 2002-05-10 00:22:55.000000000 +0200
+++ linux/include/asm-sh/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -107,10 +107,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASM_SH_IDE_H */
diff -urN linux-2.5.15/include/asm-sparc/ide.h linux/include/asm-sparc/ide.h
--- linux-2.5.15/include/asm-sparc/ide.h 2002-05-10 00:24:45.000000000 +0200
+++ linux/include/asm-sparc/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -165,11 +165,6 @@
/* __flush_dcache_range((unsigned long)src, end); */ /* P3 see hme */
}

-#define ide_ack_intr(hwif) (1)
-/* #define ide_ack_intr(hwif) ((hwif)->hw.ack_intr ? (hwif)->hw.ack_intr(hwif) : 1) */
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* _SPARC_IDE_H */
diff -urN linux-2.5.15/include/asm-sparc64/ide.h linux/include/asm-sparc64/ide.h
--- linux-2.5.15/include/asm-sparc64/ide.h 2002-05-10 00:23:37.000000000 +0200
+++ linux/include/asm-sparc64/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -181,10 +181,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* _SPARC64_IDE_H */
diff -urN linux-2.5.15/include/asm-x86_64/ide.h linux/include/asm-x86_64/ide.h
--- linux-2.5.15/include/asm-x86_64/ide.h 2002-05-10 00:24:22.000000000 +0200
+++ linux/include/asm-x86_64/ide.h 2002-05-12 16:28:29.000000000 +0200
@@ -86,10 +86,6 @@
#endif
}

-#define ide_ack_intr(hwif) (1)
-#define ide_release_lock(lock) do {} while (0)
-#define ide_get_lock(lock, hdlr, data) do {} while (0)
-
#endif /* __KERNEL__ */

#endif /* __ASMi386_IDE_H */
diff -urN linux-2.5.15/include/linux/ide.h linux/include/linux/ide.h
--- linux-2.5.15/include/linux/ide.h 2002-05-13 12:44:17.000000000 +0200
+++ linux/include/linux/ide.h 2002-05-13 03:09:01.000000000 +0200
@@ -239,6 +239,19 @@

#include <asm/ide.h>

+/* Currently only m68k, apus and m8xx need it */
+#ifdef ATA_ARCH_ACK_INTR
+# define ide_ack_intr(hwif) (hwif->hw.ack_intr ? hwif->hw.ack_intr(hwif) : 1)
+#else
+# define ide_ack_intr(hwif) (1)
+#endif
+
+/* Currently only Atari needs it */
+#ifndef ATA_ARCH_LOCK
+# define ide_release_lock(lock) do {} while (0)
+# define ide_get_lock(lock, hdlr, data) do {} while (0)
+#endif
+
/*
* If the arch-dependant ide.h did not declare/define any OUT_BYTE or IN_BYTE
* functions, we make some defaults here. The only architecture currently
@@ -324,14 +337,16 @@
* magically just go away.
*/
request_queue_t queue; /* per device request queue */
+ struct request *rq; /* current request */

unsigned long sleep; /* sleep until this time */

- byte using_dma; /* disk is using dma for read/write */
- byte using_tcq; /* disk is using queueing */
byte retry_pio; /* retrying dma capable host in pio */
byte state; /* retry state */
- byte dsc_overlap; /* flag: DSC overlap */
+
+ unsigned using_dma : 1; /* disk is using dma for read/write */
+ unsigned using_tcq : 1; /* disk is using queueing */
+ unsigned dsc_overlap : 1; /* flag: DSC overlap */

unsigned waiting_for_dma: 1; /* dma currently in progress */
unsigned busy : 1; /* currently doing revalidate_disk() */
@@ -403,11 +418,39 @@
int max_depth;
} ide_drive_t;

+/*
+ * Status returned by various functions.
+ */
+typedef enum {
+ ide_stopped, /* no drive operation was started */
+ ide_started, /* a drive operation was started, and a handler was set */
+ ide_released /* started and released bus */
+} ide_startstop_t;
+
+/*
+ * Interrupt and timeout handler type.
+ */
+typedef ide_startstop_t (ata_handler_t)(struct ata_device *, struct request *);
+typedef int (ata_expiry_t)(struct ata_device *, struct request *);
+
enum {
ATA_PRIMARY = 0,
ATA_SECONDARY = 1
};

+enum {
+ IDE_BUSY, /* awaiting an interrupt */
+ IDE_SLEEP,
+ IDE_DMA /* DMA in progress */
+};
+
+typedef struct hwgroup_s {
+ /* FIXME: We should look for busy request queues instead of looking at
+ * the !NULL state of this field.
+ */
+ ide_startstop_t (*handler)(struct ata_device *, struct request *); /* irq handler, if active */
+} ide_hwgroup_t;
+
struct ata_channel {
struct device dev; /* device handle */
int unit; /* channel number */
@@ -415,7 +458,9 @@
struct hwgroup_s *hwgroup; /* actually (ide_hwgroup_t *) */
struct timer_list timer; /* failsafe timer */
int (*expiry)(struct ata_device *, struct request *); /* irq handler, if active */
+ unsigned long poll_timeout; /* timeout value during polled operations */
struct ata_device *drive; /* last serviced drive */
+ unsigned long active; /* active processing request */

ide_ioreg_t io_ports[IDE_NR_PORTS]; /* task file registers */
hw_regs_t hw; /* Hardware info */
@@ -506,9 +551,8 @@
#endif
/* driver soft-power interface */
int (*busproc)(struct ata_device *, int);
- byte bus_state; /* power state of the IDE bus */

- unsigned long poll_timeout; /* timeout value during polled operations */
+ byte bus_state; /* power state of the IDE bus */
};

/*
@@ -517,27 +561,8 @@
extern int ide_register_hw(hw_regs_t *hw, struct ata_channel **hwifp);
extern void ide_unregister(struct ata_channel *hwif);

-/*
- * Status returned by various functions.
- */
-typedef enum {
- ide_stopped, /* no drive operation was started */
- ide_started, /* a drive operation was started, and a handler was set */
- ide_released /* started and released bus */
-} ide_startstop_t;
-
-/*
- * Interrupt and timeout handler type.
- */
-typedef ide_startstop_t (ata_handler_t)(struct ata_device *, struct request *);
-typedef int (ata_expiry_t)(struct ata_device *, struct request *);
-
struct ata_taskfile;

-#define IDE_BUSY 0 /* awaiting an interrupt */
-#define IDE_SLEEP 1
-#define IDE_DMA 2 /* DMA in progress */
-
#define IDE_MAX_TAG 32

#ifdef CONFIG_BLK_DEV_IDE_TCQ
@@ -561,15 +586,6 @@
# define ata_can_queue(drive) (1)
#endif

-typedef struct hwgroup_s {
- /* FIXME: We should look for busy request queues instead of looking at
- * the !NULL state of this field.
- */
- ide_startstop_t (*handler)(struct ata_device *, struct request *); /* irq handler, if active */
- unsigned long flags; /* BUSY, SLEEPING */
- struct request *rq; /* current request */
-} ide_hwgroup_t;
-
/* FIXME: kill this as soon as possible */
#define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
\
 
 \ /
  Last update: 2005-03-22 13:26    [W:0.772 / U:8.572 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site