lkml.org 
[lkml]   [2002]   [Oct]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: 2.5.43 scsi _eh_ buslogic
On Fri, 18 Oct 2002, Mike Anderson wrote:

> Andy,
> From looking at the driver it looks like the locking had been
> update to 2.5, but that the driver error handling has not been updated.
> scsi_obsolete.c has not existed in the 2.5 view for a while.
>
> I have cc'd linux-scsi as someone on the list might be able to
> give more information on the status of the driver.
>
> So if you where previously getting timeouts / errors on probe in 2.4 the
> older error handler might have been clearing things up and now nothing
> is being called.
>
> We should remove the older error handling interfaces as they are not
> called and possibly print a warning if a driver loads with no error
> handling functions set.
>
> The older abort handler BusLogic_AbortCommand should be easy to change
> by just adjusting the locking. I do not have one of these adapter, but
> could look into the changes.

I think it's more than Buslogic, see my similar results with NEC. There
was a CD-RW and tape drive on the controller, I unplugged the tape drive,
didn't help. See attached dmsg and ksymoops.

>
> andy barlak [andyb@island.net] wrote:
> >
> > Buslogic is still not functional in 2.5.43.
> > Info below is from successive boots on the same system.
> > Two scsi HDs and one scsi cdrom.
> > Removing the cdrom changes nothing.
> >
> > Kernel 2.4.19 has run buslogic scsi just fine:
> >
> > SCSI subsystem driver Revision: 1.00
> > PCI: Assigned IRQ 10 for device 00:08.0
> > scsi: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
> > scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
> > scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
> > scsi0: Firmware Version: 5.06J, I/O Address: 0xE800, IRQ Channel: 10/Level
> > scsi0: PCI Bus: 0, Device: 8, Address: 0xED001000, Host Adapter SCSI ID: 7
> > scsi0: Parity Checking: Disabled, Extended Translation: Disabled
> > scsi0: Synchronous Negotiation: FFFFSFF#FFFFFFFF, Wide Negotiation: YYYYNYY#YY
> > YYYYYY
> > scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
> > scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
> > scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
> > scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
> > scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Disabled
> > scsi0: SCSI Bus Termination: High Enabled, SCAM: Disabled
> > scsi0: *** BusLogic BT-958 Initialized Successfully ***
> > scsi0 : BusLogic BT-958
> > Vendor: CONNER Model: CFP2107E 2.14GB Rev: 1423
> > Type: Direct-Access ANSI SCSI revision: 02
> > Vendor: SEAGATE Model: SX423451W Rev: 9E18
> > Type: Direct-Access ANSI SCSI revision: 02
> > Vendor: TOSHIBA Model: CD-ROM XM-5701TA Rev: 0167
> > Type: CD-ROM ANSI SCSI revision: 02
> > scsi0: Target 0: Queue Depth 28, Wide Synchronous at 20.0 MB/sec, offset 15
> > scsi0: Target 1: Queue Depth 28, Wide Synchronous at 20.0 MB/sec, offset 15
> > scsi0: Target 2: Queue Depth 3, Synchronous at 10.0 MB/sec, offset 8
> > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> > Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
> > SCSI device sda: 4194303 512-byte hdwr sectors (2147 MB)
> > sda: sda1 sda2
> > SCSI device sdb: 45322644 512-byte hdwr sectors (23205 MB)
> > sdb: sdb1 sdb2 sdb3
> >
> > -----------------------------
> >
> >
> >
> > Kernel 2.5.43 and earlier produce this dmesg info
> > (edited redundant lines):
> >
> > SCSI subsystem driver Revision: 1.00
> > PCI: Assigned IRQ 10 for device 00:08.0
> > scsi: ***** BusLogic SCSI Driver Version 2.1.16 of 18 July 2002 *****
> > scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
> > scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
> > scsi0: Firmware Version: 5.06J, I/O Address: 0xE800, IRQ Channel: 10/Level
> > scsi0: PCI Bus: 0, Device: 8, Address: 0xED001000, Host Adapter SCSI ID: 7
> > scsi0: Parity Checking: Disabled, Extended Translation: Disabled
> > scsi0: Synchronous Negotiation: FFFFSFF#FFFFFFFF, Wide Negotiation: YYYYNYY#YY
> > YYYYYY
> > scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
> > scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
> > scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
> > scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
> > scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Disabled
> > scsi0: SCSI Bus Termination: High Enabled, SCAM: Disabled
> > scsi0: *** BusLogic BT-958 Initialized Successfully ***
> > scsi0 : BusLogic BT-958
> > Vendor: CONNER Model: CFP2107E 2.14GB Rev: 1423
> > Type: Direct-Access ANSI SCSI revision: 02
> > Vendor: SEAGATE Model: SX423451W Rev: 9E18
> > Type: Direct-Access ANSI SCSI revision: 02
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 1 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 1 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 2 lun 0
> > Vendor: Model: Rev:
> > Type: Direct-Access ANSI SCSI revision: 00
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 2 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 2 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 3 lun 0
> > Vendor: Model: Rev:
> > Type: Direct-Access ANSI SCSI revision: 00
> > .
> > .
> > .
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 15 lun 0
> > Vendor: Model: Rev:
> > Type: Direct-Access ANSI SCSI revision: 00
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 15 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 15 lun 0
> > st: Version 20021015, fixed bufsize 32768, wrt 30720, s/g segs 256
> > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> > Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
> > Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0
> > Attached scsi disk sdd at scsi0, channel 0, id 3, lun 0
> > Attached scsi disk sde at scsi0, channel 0, id 4, lun 0
> > Attached scsi disk sdf at scsi0, channel 0, id 5, lun 0
> > Attached scsi disk sdg at scsi0, channel 0, id 6, lun 0
> > Attached scsi disk sdh at scsi0, channel 0, id 8, lun 0
> > Attached scsi disk sdi at scsi0, channel 0, id 9, lun 0
> > Attached scsi disk sdj at scsi0, channel 0, id 10, lun 0
> > Attached scsi disk sdk at scsi0, channel 0, id 11, lun 0
> > Attached scsi disk sdl at scsi0, channel 0, id 12, lun 0
> > Attached scsi disk sdm at scsi0, channel 0, id 13, lun 0
> > Attached scsi disk sdn at scsi0, channel 0, id 14, lun 0
> > Attached scsi disk sdo at scsi0, channel 0, id 15, lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 0 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 0 lun 0
> > SCSI device sda: drive cache: write through
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 0 lun 0
> > sda : sector size 0 reported, assuming 512.
> > SCSI device sda: 1 512-byte hdwr sectors (0 MB)
> > .
> > .
> > .
> >
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 15 lun 0
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 15 lun 0
> > SCSI device sdo: drive cache: write through
> > scsi_eh_offline_sdevs: Device offlined - not ready or command retry failed after
> > error recovery: host 0 channel 0 id 15 lun 0
> > sdo : sector size 0 reported, assuming 512.
> > SCSI device sdo: 1 512-byte hdwr sectors (0 MB)
> > Initializing USB Mass Storage driver...
> >
>
> -andmike
> --
> Michael Anderson
> andmike@us.ibm.com
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>

--
bill davidsen <davidsen@tmr.com>
CTO, TMR Associates, Inc
Doing interesting things with little computers since 1979.
Linux version 2.5.43 (root@bilbo.tmr.com) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-112)) #1 SMP Fri Oct 18 17:22:39 EDT 2002
Video mode to be used for restore is ffff
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
256MB LOWMEM available.
found SMP MP-table at 000f5b30
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 65536
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61440 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 6:6 APIC version 17
Processor #1 6:6 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=2-5-43 ro root=305 BOOT_FILE=/boot/vmlinuz-2.5.43 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 498.068 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 985.08 BogoMIPS
Memory: 255104k/262144k available (1832k kernel code, 6276k reserved, 1294k data, 132k init, 0k highmem)
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU0: Intel Celeron (Mendocino) stepping 05
per-CPU timeslice cutoff: 365.46 usecs.
task migration cache decay timeout: 1 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 993.28 BogoMIPS
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU1: Intel Celeron (Mendocino) stepping 05
Total of 2 processors activated (1978.36 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-9, 2-10, 2-11, 2-17, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 71
0d 001 01 0 0 0 0 0 1 1 79
0e 001 01 0 0 0 0 0 1 1 81
0f 001 01 0 0 0 0 0 1 1 89
10 001 01 1 1 0 1 0 1 1 91
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 1 0 1 1 99
13 001 01 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:19
IRQ10 -> 0:16
IRQ11 -> 0:18
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 497.0953 MHz.
..... host bus clock speed is 82.0992 MHz.
checking TSC synchronization across 2 CPUs: passed.
Starting migration thread for cpu 0
Bringing up 1
CPU 1 IS NOW UP!
Starting migration thread for cpu 1
CPUS done 4294967295
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
mtrr: v2.0 (20020519)
PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=1
PCI: Using configuration type 1
adding '' to cpu class interfaces
adding '' to cpu class interfaces
drivers/usb/core/usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
slab: reap timer started for cpu 0
slab: reap timer started for cpu 1
Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
aio_setup: sizeof(struct page) = 40
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Capability LSM initialized
Limiting direct PCI/PCI transfers.
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Generic RTC Driver v1.06
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 204M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe0000000
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 31
exit congestion at 33
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC AC26400R, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY CD-RW CRX140E, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide1 at 0x170-0x177,0x376 on irq 15
HPT366: onboard version of chipset, pin1=1 pin2=2
HPT366: IDE controller at PCI slot 00:13.0
PCI: Enabling device 00:13.0 (0005 -> 0007)
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xe000-0xe007, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xec00-0xec07, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD205BA, ATA DISK drive
ide2 at 0xd800-0xd807,0xdc02 on irq 11
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: host protected area => 1
hda: 12594960 sectors (6449 MB) w/512KiB Cache, CHS=784/255/63, UDMA(33)
hda: hda1 hda2 hda3 hda4 < hda5 >
hde: host protected area => 1
hde: 40088160 sectors (20525 MB) w/2048KiB Cache, CHS=39770/16/63, UDMA(66)
hde: hde1
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 9, function 0
sym53c8xx: not initializing, device not supported
request_module[scsi_hostadapter]: not ready
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus]
Intel PCIC probe:
Vadem VG-468 ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets
host opts [0]: none
host opts [1]: none
ISA irqs (scanned) = 3,4,5,7 polling interval = 1000 ms
Databook TCIC-2 PCMCIA probe: not found.
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.0
drivers/usb/core/hcd-pci.c: uhci-hcd @ 00:07.2, Intel Corp. 82371AB/EB/MB PIIX4 USB
drivers/usb/core/hcd-pci.c: irq 9, io base 0000d000
drivers/usb/core/hcd.c: new USB bus registered, assigned bus number 1
drivers/usb/core/hub.c: USB hub found at 0
drivers/usb/core/hub.c: 2 ports detected
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
register interface 'mouse' with class 'input
mice: PS/2 mouse device common for all mice
logibm.c: Didn't find Logitech busmouse at 0x23c
input: PC Speaker
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
es1371: version v0.30 time 17:20:17 Oct 18 2002
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding 409648k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,5), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SONY Model: CD-RW CRX140E Rev: 1.0n
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IOMEGA Model: ZIP 100 Rev: 14.A
Type: Direct-Access ANSI SCSI revision: 00
Attached scsi removable disk sda at scsi0, channel 0, id 1, lun 0
SCSI device sda: drive cache: write back
ncr53c8xx: at PCI bus 0, device 9, function 0
ncr53c8xx: 53c825 detected
ncr53c825-0: rev 0x2 on pci bus 0 device 9 function 0 irq 9
ncr53c825-0: ID 7, Fast-10, Parity Checking
scsi1 : ncr53c8xx-3.4.3b-20010512
ncr53c825-0-<2,*>: target did not report SYNC.
Vendor: PHILIPS Model: CDD2600 Rev: 1.07
Type: CD-ROM ANSI SCSI revision: 02
SCSI device sda: drive cache: write back
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=00
sda : sense not available.
sda: Write Protect is off
sda: Mode Sense: 45 00 00 08
------------[ cut here ]------------
kernel BUG at drivers/base/core.c:269!
invalid operand: 0000
ncr53c8xx ide-scsi
CPU: 0
EIP: 0060:[<c01e2d90>] Not tainted
EFLAGS: 00010202
EIP is at put_device+0x50/0x80
eax: 00000001 ebx: cf53b964 ecx: c03ee5d0 edx: cf53b9fc
esi: cf948c98 edi: cf948c00 ebp: d08bf2e0 esp: cf60ff14
ds: 0068 es: 0068 ss: 0068
Process modprobe (pid: 332, threadinfo=cf60e000 task=cf7c7980)
Stack: 00000000 cf53b800 c022b8c9 cf53b964 fffffff4 cfde6000 00000286 c014febe
cfde6009 00000008 ff883e60 fffffffe c03bda00 00000000 c0138b4f c0138b66
c12562a0 c12562a0 000001ff 00000000 c03be400 00000000 c0138ea2 c03bda00
Call Trace:
[<c022b8c9>] scsi_unregister_host+0x259/0x540
[<c014febe>] getname+0x5e/0xa0
[<c0138b4f>] buffered_rmqueue+0x12f/0x150
[<c0138b66>] buffered_rmqueue+0x146/0x150
[<c0138ea2>] __alloc_pages+0xb2/0x290
[<d08b988a>] exit_this_scsi_driver+0xa/0xc [ncr53c8xx]
[<d08bf2e0>] driver_template+0x0/0x80 [ncr53c8xx]
[<c011c07e>] free_module+0x1e/0xf0
[<c011b454>] sys_delete_module+0x154/0x2e0
[<c010736f>] syscall_call+0x7/0xb

Code: 0f 0b 0d 01 a3 90 2e c0 8b 83 d0 00 00 00 85 c0 74 04 53 ff
<6>parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
isapnp: Scanning for PnP cards...
isapnp: Card 'NE2000 PLUG & PLAY ETHERNET CARD'
isapnp: 1 Plug & Play card detected total
ne.c:v1.10 9/23/94 Donald Becker (becker@scyld.com)
Last modified Nov 1, 2000 by Paul Gortmaker
NE*000 ethercard probe at 0x300: 00 00 e8 46 6d a1
eth0: NE2000 found at 0x300, using IRQ 3.
eth0: interrupt from stopped card
ne.c: ISAPnP reports Generic PNP at i/o 0x220, irq 5.
NE*000 ethercard probe at 0x220: 00 00 e8 46 6d a1
eth1: NE2000 found at 0x220, using IRQ 5.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x290-0x297 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: excluding 0xa20-0xa2f
ksymoops 2.4.4 on i686 2.5.43. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.5.43/ (default)
-m /boot/System.map-2.5.43 (default)

Warning: You did not tell me where to find symbol information. I will
assume that the log matches the kernel and modules that are running
right now and I'll use the default options above for symbol resolution.
If the current kernel and/or modules do not match the log, you can get
more accurate output by telling me the kernel version and where to find
map, modules, ksyms etc. ksymoops -h explains the options.

Warning (compare_ksyms_lsmod): module ncr53c8xx is in lsmod but not in ksyms, probably no symbols exported
kernel BUG at drivers/base/core.c:269!
invalid operand: 0000
CPU: 0
EIP: 0060:[<c01e2d90>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010202
eax: 00000001 ebx: cf53b964 ecx: c03ee5d0 edx: cf53b9fc
esi: cf948c98 edi: cf948c00 ebp: d08bf2e0 esp: cf60ff14
ds: 0068 es: 0068 ss: 0068
Stack: 00000000 cf53b800 c022b8c9 cf53b964 fffffff4 cfde6000 00000286 c014febe
cfde6009 00000008 ff883e60 fffffffe c03bda00 00000000 c0138b4f c0138b66
c12562a0 c12562a0 000001ff 00000000 c03be400 00000000 c0138ea2 c03bda00
[<c022b8c9>] scsi_unregister_host+0x259/0x540
[<c014febe>] getname+0x5e/0xa0
[<c0138b4f>] buffered_rmqueue+0x12f/0x150
[<c0138b66>] buffered_rmqueue+0x146/0x150
[<c0138ea2>] __alloc_pages+0xb2/0x290
[<d08b988a>] exit_this_scsi_driver+0xa/0xc [ncr53c8xx]
[<d08bf2e0>] driver_template+0x0/0x80 [ncr53c8xx]
[<c011c07e>] free_module+0x1e/0xf0
[<c011b454>] sys_delete_module+0x154/0x2e0
[<c010736f>] syscall_call+0x7/0xb
Code: 0f 0b 0d 01 a3 90 2e c0 8b 83 d0 00 00 00 85 c0 74 04 53 ff

>>EIP; c01e2d90 <put_device+50/80> <=====
Code; c01e2d90 <put_device+50/80>
00000000 <_EIP>:
Code; c01e2d90 <put_device+50/80> <=====
0: 0f 0b ud2a <=====
Code; c01e2d92 <put_device+52/80>
2: 0d 01 a3 90 2e or $0x2e90a301,%eax
Code; c01e2d97 <put_device+57/80>
7: c0 8b 83 d0 00 00 00 rorb $0x0,0xd083(%ebx)
Code; c01e2d9e <put_device+5e/80>
e: 85 c0 test %eax,%eax
Code; c01e2da0 <put_device+60/80>
10: 74 04 je 16 <_EIP+0x16> c01e2da6 <put_device+66/80>
Code; c01e2da2 <put_device+62/80>
12: 53 push %ebx
Code; c01e2da3 <put_device+63/80>
13: ff 00 incl (%eax)


2 warnings issued. Results may not be reliable.
\
 
 \ /
  Last update: 2005-03-22 13:30    [W:0.070 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site