lkml.org 
[lkml]   [2002]   [Oct]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH][RFC] add support for PC-9800 architecture (19/26) SCSI
This is part 19/26 of patchset for add support NEC PC-9800 architecture,
against 2.5.43.

Summary:
SCSI driver related modules.
- replace bios_param function.
- add new driver. (pc980155)
- export sd_get_sdisk to get disk goemetry.
we need disk geometry to read partition table.

diffstat:
drivers/scsi/Config.in | 3
drivers/scsi/Makefile | 1
drivers/scsi/advansys.c | 9 +
drivers/scsi/aic7xxx/aic7xxx_linux_host.h | 3
drivers/scsi/aic7xxx_old/aic7xxx.h | 9 -
drivers/scsi/pc980155.c | 262 ++++++++++++++++++++++++++++++
drivers/scsi/pc980155.h | 47 +++++
drivers/scsi/pc980155regs.h | 89 ++++++++++
drivers/scsi/scsi_scan.c | 1
drivers/scsi/scsi_syms.c | 6
drivers/scsi/scsicam.c | 93 ++++++++++
drivers/scsi/sd.c | 8
drivers/scsi/wd33c93.c | 112 ++++++++++--
drivers/scsi/wd33c93.h | 5
include/scsi/scsicam.h | 5
15 files changed, 635 insertions(+), 18 deletions(-)

patch:
diff -urN linux/drivers/scsi/Config.in linux98/drivers/scsi/Config.in
--- linux/drivers/scsi/Config.in Sat Oct 12 13:22:05 2002
+++ linux98/drivers/scsi/Config.in Sun Oct 13 18:26:42 2002
@@ -258,6 +258,9 @@
# bool 'GVP Turbo 040/060 SCSI support (EXPERIMENTAL)' CONFIG_GVP_TURBO_SCSI
fi
fi
+if [ "$CONFIG_PC9800" = "y" ]; then
+ dep_tristate 'NEC PC-9801-55 SCSI support' CONFIG_SCSI_PC980155 $CONFIG_SCSI
+fi

endmenu

diff -urN linux/drivers/scsi/Makefile linux98/drivers/scsi/Makefile
--- linux/drivers/scsi/Makefile Sat Oct 12 13:21:35 2002
+++ linux98/drivers/scsi/Makefile Sun Oct 13 18:28:50 2002
@@ -31,6 +31,7 @@
obj-$(CONFIG_A3000_SCSI) += a3000.o wd33c93.o
obj-$(CONFIG_A2091_SCSI) += a2091.o wd33c93.o
obj-$(CONFIG_GVP11_SCSI) += gvp11.o wd33c93.o
+obj-$(CONFIG_SCSI_PC980155) += pc980155.o wd33c93.o
obj-$(CONFIG_MVME147_SCSI) += mvme147.o wd33c93.o
obj-$(CONFIG_SGIWD93_SCSI) += sgiwd93.o wd33c93.o
obj-$(CONFIG_CYBERSTORM_SCSI) += NCR53C9x.o cyberstorm.o
diff -urN linux/drivers/scsi/advansys.c linux98/drivers/scsi/advansys.c
--- linux/drivers/scsi/advansys.c Wed Oct 16 13:20:38 2002
+++ linux98/drivers/scsi/advansys.c Wed Oct 16 15:26:55 2002
@@ -815,6 +815,9 @@
#ifdef CONFIG_PCI
#include <linux/pci.h>
#endif /* CONFIG_PCI */
+#ifdef CONFIG_PC9800
+#include <scsi/scsicam.h>
+#endif


/*
@@ -6117,10 +6120,13 @@
int
advansys_biosparam(Disk *dp, struct block_device *dep, int ip[])
{
+#ifndef CONFIG_PC9800
asc_board_t *boardp;
+#endif

ASC_DBG(1, "advansys_biosparam: begin\n");
ASC_STATS(dp->device->host, biosparam);
+#ifndef CONFIG_PC9800
boardp = ASC_BOARDP(dp->device->host);
if (ASC_NARROW_BOARD(boardp)) {
if ((boardp->dvc_var.asc_dvc_var.dvc_cntl &
@@ -6142,6 +6148,9 @@
}
}
ip[2] = (unsigned long)dp->capacity / (ip[0] * ip[1]);
+#else /* CONFIG_PC9800 */
+ pc9800_scsi_bios_param(dp, dep, ip);
+#endif /* !CONFIG_PC9800 */
ASC_DBG(1, "advansys_biosparam: end\n");
return 0;
}
diff -urN linux/drivers/scsi/aic7xxx/aic7xxx_linux_host.h linux98/drivers/scsi/aic7xxx/aic7xxx_linux_host.h
--- linux/drivers/scsi/aic7xxx/aic7xxx_linux_host.h Fri Apr 12 13:57:53 2002
+++ linux98/drivers/scsi/aic7xxx/aic7xxx_linux_host.h Fri Apr 12 15:45:26 2002
@@ -52,7 +52,8 @@
int ahc_linux_dev_reset(Scsi_Cmnd *);
int ahc_linux_abort(Scsi_Cmnd *);

-#if defined(__i386__)
+#include <linux/config.h>
+#if defined(__i386__) && !defined(CONFIG_PC9800)
# define AIC7XXX_BIOSPARAM ahc_linux_biosparam
#else
# define AIC7XXX_BIOSPARAM NULL
diff -urN linux/drivers/scsi/aic7xxx_old/aic7xxx.h linux98/drivers/scsi/aic7xxx_old/aic7xxx.h
--- linux/drivers/scsi/aic7xxx_old/aic7xxx.h Sat Oct 12 13:21:03 2002
+++ linux98/drivers/scsi/aic7xxx_old/aic7xxx.h Sat Oct 12 19:08:22 2002
@@ -23,6 +23,13 @@
#ifndef _aic7xxx_h
#define _aic7xxx_h

+#include <linux/config.h>
+
+#ifndef CONFIG_PC9800
+# define AIC7XXX_BIOSPARAM aic7xxx_biosparam
+#else
+# define AIC7XXX_BIOSPARAM NULL
+#endif
#define AIC7XXX_H_VERSION "5.2.0"

/*
@@ -48,7 +55,7 @@
reset: aic7xxx_reset, \
slave_attach: aic7xxx_slave_attach, \
slave_detach: aic7xxx_slave_detach, \
- bios_param: aic7xxx_biosparam, \
+ bios_param: AIC7XXX_BIOSPARAM, \
can_queue: 255, /* max simultaneous cmds */\
this_id: -1, /* scsi id of host adapter */\
sg_tablesize: 0, /* max scatter-gather cmds */\
diff -urN linux/drivers/scsi/pc980155.c linux98/drivers/scsi/pc980155.c
--- linux/drivers/scsi/pc980155.c Thu Jan 1 09:00:00 1970
+++ linux98/drivers/scsi/pc980155.c Sun Feb 3 12:08:14 2002
@@ -0,0 +1,262 @@
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/mm.h>
+#include <linux/blk.h>
+#include <linux/sched.h>
+#include <linux/version.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/irq.h>
+#include <asm/dma.h>
+#include <linux/module.h>
+
+#include "scsi.h"
+#include "hosts.h"
+#include "wd33c93.h"
+#include "pc980155.h"
+#include "pc980155regs.h"
+
+#define DEBUG
+
+#include<linux/stat.h>
+
+static inline void __print_debug_info(unsigned int);
+static inline void __print_debug_info(unsigned int a){}
+#define print_debug_info() __print_debug_info(base_io);
+
+#define NR_BASE_IOS 4
+static int nr_base_ios = NR_BASE_IOS;
+static unsigned int base_ios[NR_BASE_IOS] = {0xcc0, 0xcd0, 0xce0, 0xcf0};
+static unsigned int SASR;
+static unsigned int SCMD;
+static wd33c93_regs regs = {&SASR, &SCMD};
+
+static struct Scsi_Host *pc980155_host = NULL;
+
+static void pc980155_intr_handle(int irq, void *dev_id, struct pt_regs *regp);
+
+inline void pc980155_dma_enable(unsigned int base_io){
+ outb(0x01, REG_CWRITE);
+ WAIT();
+}
+inline void pc980155_dma_disable(unsigned int base_io){
+ outb(0x02, REG_CWRITE);
+ WAIT();
+}
+
+
+static void pc980155_intr_handle(int irq, void *dev_id, struct pt_regs *regp)
+{
+ wd33c93_intr(pc980155_host);
+}
+
+static int dma_setup(Scsi_Cmnd *sc, int dir_in){
+ /*
+ * sc->SCp.this_residual : transfer count
+ * sc->SCp.ptr : distination address (virtual address)
+ * dir_in : data direction (DATA_OUT_DIR:0 or DATA_IN_DIR:1)
+ *
+ * if success return 0
+ */
+
+ /*
+ * DMA WRITE MODE
+ * bit 7,6 01b single mode (this mode only)
+ * bit 5 inc/dec (default:0 = inc)
+ * bit 4 auto initialize (normaly:0 = off)
+ * bit 3,2 01b memory -> io
+ * 10b io -> memory
+ * 00b verify
+ * bit 1,0 channel
+ */
+ disable_dma(sc->host->dma_channel);
+ set_dma_mode(sc->host->dma_channel, 0x40 | (dir_in ? 0x04 : 0x08));
+ clear_dma_ff(sc->host->dma_channel);
+ set_dma_addr(sc->host->dma_channel, virt_to_phys(sc->SCp.ptr));
+ set_dma_count(sc->host->dma_channel, sc->SCp.this_residual);
+#if 0
+#ifdef DEBUG
+ printk("D%d(%x)D", sc->SCp.this_residual);
+#endif
+#endif
+ enable_dma(sc->host->dma_channel);
+
+ pc980155_dma_enable(sc->host->io_port);
+
+ return 0;
+}
+
+static void dma_stop(struct Scsi_Host *instance, Scsi_Cmnd *sc, int status){
+ /*
+ * instance: Hostadapter's instance
+ * sc: scsi command
+ * status: True if success
+ */
+
+ pc980155_dma_disable(sc->host->io_port);
+
+ disable_dma(sc->host->dma_channel);
+}
+
+/* return non-zero on detection */
+static inline int pc980155_test_port(wd33c93_regs regs)
+{
+ /* Quick and dirty test for presence of the card. */
+ if (READ_AUX_STAT() == 0xff)
+ return 0;
+ return 1;
+}
+
+static inline int
+pc980155_getconfig(unsigned int base_io, wd33c93_regs regs,
+ unsigned char* irq, unsigned char* dma,
+ unsigned char* scsi_id)
+{
+ static unsigned char irqs[] = { 3, 5, 6, 9, 12, 13 };
+ unsigned char result;
+
+ printk(KERN_DEBUG "PC-9801-55: base_io=%x SASR=%x SCMD=%x\n",
+ base_io, *regs.SASR, *regs.SCMD);
+ result = read_wd33c93(regs, WD_RESETINT);
+ printk(KERN_DEBUG "PC-9801-55: getting config (%x)\n", result);
+ *scsi_id = result & 0x07;
+ *irq = (result >> 3) & 0x07;
+ if (*irq > 5) {
+ printk(KERN_ERR "PC-9801-55 (base %#x): impossible IRQ (%d)"
+ " - other device here?\n", base_io, *irq);
+ return 0;
+ }
+
+ *irq = irqs[*irq];
+ result = inb(REG_STATRD);
+ WAIT();
+ *dma = result & 0x03;
+ if (*dma == 1) {
+ printk(KERN_ERR
+ "PC-9801-55 (base %#x): impossible DMA channl (%d)"
+ " - other device here?\n", base_io, *dma);
+ return 0;
+ }
+#ifdef DEBUG
+ printk("PC-9801-55: end of getconfig\n");
+#endif
+ return 1;
+}
+
+/* return non-zero on detection */
+int scsi_pc980155_detect(Scsi_Host_Template* tpnt)
+{
+ unsigned int base_io;
+ unsigned char irq, dma, scsi_id;
+ int i;
+#ifdef DEBUG
+ unsigned char debug;
+#endif
+
+ for (i = 0; i < nr_base_ios; i++) {
+ base_io = base_ios[i];
+ SASR = REG_ADDRST;
+ SCMD = REG_CONTRL;
+
+ /* printk("PC-9801-55: SASR(%x = %x)\n", SASR, REG_ADDRST); */
+ if (check_region(base_io, 6))
+ continue;
+ if (! pc980155_test_port(regs))
+ continue;
+
+ if (!pc980155_getconfig(base_io, regs, &irq, &dma, &scsi_id))
+ continue;
+#ifdef DEBUG
+ printk("PC-9801-55: config: base io = %x, irq = %d, dma channel = %d, scsi id = %d\n",
+ base_io, irq, dma, scsi_id);
+#endif
+ if (request_irq(irq, pc980155_intr_handle, 0, "PC-9801-55",
+ NULL)) {
+ printk(KERN_ERR
+ "PC-9801-55: unable to allocate IRQ %d\n",
+ irq);
+ continue;
+ }
+ if (request_dma(dma, "PC-9801-55")) {
+ printk(KERN_ERR "PC-9801-55: "
+ "unable to allocate DMA channel %d\n", dma);
+ free_irq(irq, NULL);
+ continue;
+ }
+
+ request_region(base_io, 6, "PC-9801-55");
+ pc980155_host = scsi_register(tpnt, sizeof(struct WD33C93_hostdata));
+ pc980155_host->this_id = scsi_id;
+ pc980155_host->io_port = base_io;
+ pc980155_host->n_io_port = 6;
+ pc980155_host->irq = irq;
+ pc980155_host->dma_channel = dma;
+
+#ifdef DEBUG
+ printk("PC-9801-55: scsi host found at %x irq = %d, use dma channel %d.\n", base_io, irq, dma);
+ debug = read_aux_stat(regs);
+ printk("PC-9801-55: aux: %x ", debug);
+ debug = read_wd33c93(regs, 0x17);
+ printk("status: %x\n", debug);
+#endif
+
+ pc980155_int_enable(regs);
+
+ wd33c93_init(pc980155_host, regs, dma_setup, dma_stop,
+ WD33C93_FS_12_15);
+
+ return 1;
+ }
+
+ printk("PC-9801-55: not found\n");
+ return 0;
+}
+
+int pc980155_proc_info(char *buf, char **start, off_t off, int len,
+ int hostno, int in)
+{
+ /* NOT SUPPORTED YET! */
+
+ if (in) {
+ return -EPERM;
+ }
+ *start = buf;
+ return sprintf(buf, "Sorry, not supported yet.\n");
+}
+
+int pc980155_setup(char *str)
+{
+next:
+ if (!strncmp(str, "io:", 3)){
+ base_ios[0] = simple_strtoul(str+3,NULL,0);
+ nr_base_ios = 1;
+ while (*str > ' ' && *str != ',')
+ str++;
+ if (*str == ','){
+ str++;
+ goto next;
+ }
+ }
+ return 0;
+}
+
+int scsi_pc980155_release(struct Scsi_Host *pc980155_host)
+{
+#ifdef MODULE
+ pc980155_int_disable(regs);
+ release_region(pc980155_host->io_port, pc980155_host->n_io_port);
+ free_irq(pc980155_host->irq, NULL);
+ free_dma(pc980155_host->dma_channel);
+ wd33c93_release();
+#endif
+ return 1;
+}
+
+__setup("pc980155=", pc980155_setup);
+
+Scsi_Host_Template driver_template = SCSI_PC980155;
+
+#include "scsi_module.c"
diff -urN linux/drivers/scsi/pc980155.h linux98/drivers/scsi/pc980155.h
--- linux/drivers/scsi/pc980155.h Thu Jan 1 09:00:00 1970
+++ linux98/drivers/scsi/pc980155.h Sun Feb 3 12:08:14 2002
@@ -0,0 +1,47 @@
+/*
+ * PC-9801-55 SCSI host adapter driver
+ *
+ * Copyright (C) 1997-2000 Kyoto University Microcomputer Club
+ * (Linux/98 project)
+ */
+
+#ifndef _SCSI_PC9801_55_H
+#define _SCSI_PC9801_55_H
+
+#include <linux/types.h>
+#include <linux/kdev_t.h>
+#include <scsi/scsicam.h>
+
+int wd33c93_queuecommand(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
+int wd33c93_abort(Scsi_Cmnd *);
+int wd33c93_reset(Scsi_Cmnd *, unsigned int);
+int scsi_pc980155_detect(Scsi_Host_Template *);
+int scsi_pc980155_release(struct Scsi_Host *);
+int pc980155_proc_info(char *, char **, off_t, int, int, int);
+
+#ifndef CMD_PER_LUN
+#define CMD_PER_LUN 2
+#endif
+
+#ifndef CAN_QUEUE
+#define CAN_QUEUE 16
+#endif
+
+#define SCSI_PC980155 { proc_name: "PC-9801-55", \
+ name: "SCSI PC-9801-55", \
+ proc_info: pc980155_proc_info, \
+ detect: scsi_pc980155_detect, \
+ release: scsi_pc980155_release, \
+ /* command: use queue command */ \
+ queuecommand: wd33c93_queuecommand, \
+ abort: wd33c93_abort, \
+ reset: wd33c93_reset, \
+ bios_param: pc9800_scsi_bios_param, \
+ can_queue: CAN_QUEUE, \
+ this_id: 7, \
+ sg_tablesize: SG_ALL, \
+ cmd_per_lun: CMD_PER_LUN, /* dont use link command */ \
+ unchecked_isa_dma: 1, /* use dma **XXXX***/ \
+ use_clustering: ENABLE_CLUSTERING }
+
+#endif /* _SCSI_PC9801_55_H */
diff -urN linux/drivers/scsi/pc980155regs.h linux98/drivers/scsi/pc980155regs.h
--- linux/drivers/scsi/pc980155regs.h Thu Jan 1 09:00:00 1970
+++ linux98/drivers/scsi/pc980155regs.h Mon Dec 3 18:44:10 2001
@@ -0,0 +1,89 @@
+#ifndef __PC980155REGS_H
+#define __PC980155REGS_H
+
+#include "wd33c93.h"
+
+#define REG_ADDRST (base_io+0)
+#define REG_CONTRL (base_io+2)
+#define REG_CWRITE (base_io+4)
+#define REG_STATRD (base_io+4)
+
+#define WD_MEMORYBANK 0x30
+#define WD_RESETINT 0x33
+
+#if 0
+#define WAIT() outb(0x00,0x5f)
+#else
+#define WAIT() do{}while(0)
+#endif
+
+static inline uchar read_wd33c93(const wd33c93_regs regs, uchar reg_num)
+{
+ uchar data;
+ outb(reg_num, *regs.SASR);
+ WAIT();
+ data = inb(*regs.SCMD);
+ WAIT();
+ return data;
+}
+
+static inline uchar read_aux_stat(const wd33c93_regs regs)
+{
+ uchar result;
+ result = inb(*regs.SASR);
+ WAIT();
+ /* printk("PC-9801-55: regp->SASR(%x) = %x\n", regp->SASR, result); */
+ return result;
+}
+#define READ_AUX_STAT() read_aux_stat(regs)
+
+static inline void write_wd33c93(const wd33c93_regs regs, uchar reg_num,
+ uchar value)
+{
+ outb(reg_num, *regs.SASR);
+ WAIT();
+ outb(value, *regs.SCMD);
+ WAIT();
+}
+
+
+#define write_wd33c93_cmd(regs,cmd) write_wd33c93(regs,WD_COMMAND,cmd)
+
+static inline void write_wd33c93_count(const wd33c93_regs regs,
+ unsigned long value)
+{
+ outb(WD_TRANSFER_COUNT_MSB, *regs.SASR);
+ WAIT();
+ outb((value >> 16) & 0xff, *regs.SCMD);
+ WAIT();
+ outb((value >> 8) & 0xff, *regs.SCMD);
+ WAIT();
+ outb( value & 0xff, *regs.SCMD);
+ WAIT();
+}
+
+
+static inline unsigned long read_wd33c93_count(const wd33c93_regs regs)
+{
+unsigned long value;
+
+ outb(WD_TRANSFER_COUNT_MSB, *regs.SASR);
+ value = inb(*regs.SCMD) << 16;
+ value |= inb(*regs.SCMD) << 8;
+ value |= inb(*regs.SCMD);
+ return value;
+}
+
+static inline void write_wd33c93_cdb(const wd33c93_regs regs, unsigned int len,
+ unsigned char cmnd[])
+{
+ int i;
+ outb(WD_CDB_1, *regs.SASR);
+ for (i=0; i<len; i++)
+ outb(cmnd[i], *regs.SCMD);
+}
+
+#define pc980155_int_enable(regs) write_wd33c93(regs, WD_MEMORYBANK, read_wd33c93(regs, WD_MEMORYBANK) | 0x04)
+#define pc980155_int_disable(regs) write_wd33c93(regs, WD_MEMORYBANK, read_wd33c93(regs, WD_MEMORYBANK) & ~0x04)
+
+#endif
diff -urN linux/drivers/scsi/scsi_scan.c linux98/drivers/scsi/scsi_scan.c
--- linux/drivers/scsi/scsi_scan.c Wed Aug 28 09:52:26 2002
+++ linux98/drivers/scsi/scsi_scan.c Wed Aug 28 13:09:39 2002
@@ -131,6 +131,7 @@
{"MITSUMI", "CD-R CR-2201CS", "6119", BLIST_NOLUN}, /* locks up */
{"RELISYS", "Scorpio", NULL, BLIST_NOLUN}, /* responds to all lun */
{"MICROTEK", "ScanMaker II", "5.61", BLIST_NOLUN}, /* responds to all lun */
+ {"NEC", "D3856", "0009", BLIST_NOLUN},

/*
* Other types of devices that have special flags.
diff -urN linux/drivers/scsi/scsi_syms.c linux98/drivers/scsi/scsi_syms.c
--- linux/drivers/scsi/scsi_syms.c Wed Oct 16 13:20:40 2002
+++ linux98/drivers/scsi/scsi_syms.c Wed Oct 16 15:26:55 2002
@@ -96,6 +96,12 @@
EXPORT_SYMBOL(scsi_devicelist);
EXPORT_SYMBOL(scsi_device_types);

+#ifdef CONFIG_PC9800
+EXPORT_SYMBOL(pc9800_scsi_bios_param);
+extern Scsi_Disk * sd_get_sdisk(int);
+EXPORT_SYMBOL(sd_get_sdisk);
+#endif
+
/*
* Externalize timers so that HBAs can safely start/restart commands.
*/
diff -urN linux/drivers/scsi/scsicam.c linux98/drivers/scsi/scsicam.c
--- linux/drivers/scsi/scsicam.c Thu Jul 25 06:03:18 2002
+++ linux98/drivers/scsi/scsicam.c Fri Jul 26 11:31:23 2002
@@ -12,6 +12,8 @@

#include <linux/module.h>

+#include <linux/config.h>
+
#include <linux/fs.h>
#include <linux/genhd.h>
#include <linux/kernel.h>
@@ -61,7 +63,18 @@
int ret_code;
int size = disk->capacity;
unsigned long temp_cyl;
+#ifndef CONFIG_PC9800
unsigned char *p = scsi_bios_ptable(bdev);
+#else
+ unsigned char *p;
+#endif
+
+#ifdef CONFIG_PC9800
+ if (!pc9800_scsi_bios_param(disk, bdev, ip))
+ return 0;
+
+ p = scsi_bios_ptable(bdev);
+#endif

if (!p)
return -1;
@@ -238,3 +251,83 @@
*hds = (unsigned int) heads;
return (rv);
}
+
+#ifdef CONFIG_PC9800
+
+#include <asm/pc9800.h>
+
+/* XXX - For now, we assume the first (i.e. having the least host_no)
+ real (i.e. non-emulated) host adapter shall be BIOS-controlled one.
+ We *SHOULD* invent another way. */
+
+static inline struct Scsi_Host *first_real_host(void)
+{
+ struct Scsi_Host *first, *h;
+
+ for (first = NULL, h = scsi_hostlist; h; h = h->next)
+ if (!h->hostt->emulated
+ && (!first || h->host_no < first->host_no))
+ first = h;
+ return first;
+}
+
+/* There is no standard device-to-name translation function. Sigh. */
+static inline void sd_devname(char *buf, kdev_t dev)
+{
+ int diskno = (major(dev) & SD_MAJOR_MASK) * 16 + (minor(dev) >> 4);
+
+ buf[0] = 'a' + diskno;
+ buf[1] = '\0';
+ if (diskno >= 26) {
+ buf[0] = 'a' + (diskno / 26 - 1);
+ buf[1] = 'a' + (diskno % 26);
+ buf[2] = '\0';
+ }
+}
+
+int pc9800_scsi_bios_param(Disk *disk, struct block_device *bdev, int *ip)
+{
+ char namebuf[4];
+
+ sd_devname(namebuf, to_kdev_t(bdev->bd_dev));
+
+ if (first_real_host () == disk->device->host
+ && disk->device->id < 7
+ && __PC9800SCA_TEST_BIT(PC9800SCA_DISK_EQUIPS, disk->device->id))
+ {
+ const u8 *p = (&__PC9800SCA(u8, PC9800SCA_SCSI_PARAMS)
+ + disk->device->id * 4);
+
+ ip[0] = p[1]; /* # of heads */
+ ip[1] = p[0]; /* # of sectors/track */
+ ip[2] = *(u16 *)&p[2] & 0x0FFF; /* # of cylinders */
+ if (p[3] & (1 << 6)) { /* #-of-cylinders is 16-bit */
+ ip[2] |= (ip[0] & 0xF0) << 8;
+ ip[0] &= 0x0F;
+ }
+ printk(KERN_INFO "sd%s: "
+ "BIOS parameters CHS:%d/%d/%d, %u bytes %s sector\n",
+ namebuf, ip[2], ip[0], ip[1], 256 << ((p[3] >> 4) & 3),
+ p[3] & 0x80 ? "hard" : "soft");
+ return 0;
+ }
+
+ /* Assume PC-9801-92 compatible parameters for HAs without BIOS. */
+ ip[0] = 8;
+ ip[1] = 32;
+ ip[2] = disk->capacity / (8 * 32);
+ if (ip[2] > 65535) { /* if capacity >= 8GB */
+ /* Recent on-board adapters seem to use this parameter. */
+ ip[1] = 128;
+ ip[2] = disk->capacity / (8 * 128);
+ if (ip[2] > 65535) { /* if capacity >= 32GB */
+ /* Clip the number of cylinders. Currently this
+ is the limit that we deal with. */
+ ip[2] = 65535;
+ }
+ }
+ printk(KERN_INFO "sd%s: BIOS parameters CHS:%d/%d/%d (assumed)\n",
+ namebuf, ip[2], ip[0], ip[1]);
+ return 0;
+}
+#endif /* CONFIG_PC9800 */
diff -urN linux/drivers/scsi/sd.c linux98/drivers/scsi/sd.c
--- linux/drivers/scsi/sd.c Wed Oct 16 13:20:40 2002
+++ linux98/drivers/scsi/sd.c Wed Oct 16 15:26:55 2002
@@ -125,7 +125,11 @@

static void sd_rw_intr(Scsi_Cmnd * SCpnt);

+#ifndef CONFIG_PC9800
static Scsi_Disk * sd_get_sdisk(int index);
+#else
+Scsi_Disk * sd_get_sdisk(int index);
+#endif

#if defined(CONFIG_PPC32)
/**
@@ -1638,7 +1642,11 @@
return (the_result == 0);
}

+#ifndef CONFIG_PC9800
static Scsi_Disk * sd_get_sdisk(int index)
+#else
+Scsi_Disk * sd_get_sdisk(int index)
+#endif
{
Scsi_Disk * sdkp = NULL;
unsigned long iflags;
diff -urN linux/drivers/scsi/wd33c93.c linux98/drivers/scsi/wd33c93.c
--- linux/drivers/scsi/wd33c93.c Fri Aug 2 06:16:08 2002
+++ linux98/drivers/scsi/wd33c93.c Wed Aug 7 13:07:51 2002
@@ -84,12 +84,17 @@
#include <linux/init.h>
#include <asm/irq.h>
#include <linux/blk.h>
+#include <linux/spinlock.h>

#include "scsi.h"
#include "hosts.h"


+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+#define WD33C93_VERSION "1.25-pc98"
+#else
#define WD33C93_VERSION "1.25"
+#endif
#define WD33C93_DATE "09/Jul/1997"
/* NOTE: 1.25 for m68k is related to in2000-1.31 for x86 */

@@ -173,7 +178,13 @@
MODULE_PARM(setup_strings, "s");
#endif

+static spinlock_t wd_lock = SPIN_LOCK_UNLOCKED;
+
+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+
+#include "pc980155regs.h"

+#else /* !CONFIG_SCSI_PC980155 */

static inline uchar read_wd33c93(const wd33c93_regs regs, uchar reg_num)
{
@@ -203,6 +214,7 @@
*regs.SCMD = cmd;
mb();
}
+#endif /* CONFIG_SCSI_PC980155 */


static inline uchar read_1_byte(const wd33c93_regs regs)
@@ -220,6 +232,11 @@
return x;
}

+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+
+#include "pc980155regs.h"
+
+#else /* !CONFIG_SCSI_PC980155 */

static void write_wd33c93_count(const wd33c93_regs regs, unsigned long value)
{
@@ -244,6 +261,7 @@
mb();
return value;
}
+#endif /* CONFIG_SCSI_PC980155 */


/* The 33c93 needs to be told which direction a command transfers its
@@ -385,8 +403,9 @@
* sense data is not lost before REQUEST_SENSE executes.
*/

- save_flags(flags);
- cli();
+ //save_flags(flags);
+ //cli();
+ spin_lock_irqsave(&wd_lock, flags);

if (!(hostdata->input_Q) || (cmd->cmnd[0] == REQUEST_SENSE)) {
cmd->host_scribble = (uchar *)hostdata->input_Q;
@@ -407,7 +426,8 @@

DB(DB_QUEUE_COMMAND,printk(")Q-%ld ",cmd->pid))

- restore_flags(flags);
+ //restore_flags(flags);
+ spin_unlock_irqrestore(&wd_lock, flags);
return 0;
}

@@ -428,7 +448,9 @@
struct WD33C93_hostdata *hostdata = (struct WD33C93_hostdata *)instance->hostdata;
const wd33c93_regs regs = hostdata->regs;
Scsi_Cmnd *cmd, *prev;
+#ifdef DEBUG
int i;
+#endif

DB(DB_EXECUTE,printk("EX("))

@@ -462,6 +484,16 @@
return;
}

+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+#ifdef DEBUG
+printk("exec: command = [");
+for (i=0; i<12; i++){
+ printk(" %02x", cmd->cmnd[i]);
+}
+printk("]\nexec: target = %d\n", cmd->target);
+#endif
+#endif
+
/* remove command from queue */

if (prev)
@@ -591,9 +623,13 @@
* (take advantage of auto-incrementing)
*/

+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+ write_wd33c93_cdb(regs, cmd->cmd_len, cmd->cmnd);
+#else /* !CONFIG_SCSI_PC980155 */
*regs.SASR = WD_CDB_1;
for (i=0; i<cmd->cmd_len; i++)
*regs.SCMD = cmd->cmnd[i];
+#endif /* CONFIG_SCSI_PC980155 */

/* The wd33c93 only knows about Group 0, 1, and 5 commands when
* it's doing a 'select-and-transfer'. To be safe, we write the
@@ -765,7 +801,7 @@
if (!(asr & ASR_INT) || (asr & ASR_BSY))
return;

- save_flags(flags);
+ local_save_flags(flags);

#ifdef PROC_STATISTICS
hostdata->int_cnt++;
@@ -777,6 +813,46 @@

DB(DB_INTR,printk("{%02x:%02x-",asr,sr))

+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+#ifdef DEBUG
+ {
+ int i;
+ static uchar old_phs=0;
+ printk("**interrupt ");
+ if (cmd){
+ printk("cmd[");
+ for (i=0; i<cmd->cmd_len-1; i++){
+ printk("%02x ",cmd->cmnd[i]);
+ }
+ printk("%02x] ",cmd->cmnd[i]);
+ } else {
+ printk("NoConnectedCmd ");
+ }
+ printk("asr=%02x sr=%02x phs=%02x\n",asr,sr,phs);
+
+ if (sr==0x49){
+ if (phs==old_phs){
+ for (i = 0; i < cmd->SCp.this_residual; i++){
+ printk("%02x", cmd->SCp.buffer);
+ switch (i % 32){
+ case 7: case 15: case 23:
+ printk(" ");
+ break;
+ case 31:
+ printk("\n");
+ break;
+ default:
+ break;
+ }
+ }
+ panic("");
+ } else
+ old_phs = phs;
+ }
+ }
+#endif
+#endif
+
/* After starting a DMA transfer, the next interrupt
* is guaranteed to be in response to completion of
* the transfer. Since the Amiga DMA hardware runs in
@@ -831,7 +907,7 @@
* is here...
*/

- restore_flags(flags);
+ local_irq_restore(flags);

/* We are not connected to a target - check to see if there
* are commands waiting to be executed.
@@ -1085,7 +1161,7 @@
write_wd33c93_cmd(regs, WD_CMD_NEGATE_ACK);
hostdata->state = S_CONNECTED;
}
- restore_flags(flags);
+ local_irq_restore(flags);
break;


@@ -1117,7 +1193,7 @@
/* We are no longer connected to a target - check to see if
* there are commands waiting to be executed.
*/
- restore_flags(flags);
+ local_irq_restore(flags);
wd33c93_execute(instance);
}
else {
@@ -1200,7 +1276,7 @@
* there are commands waiting to be executed.
*/
/* look above for comments on scsi_done() */
- restore_flags(flags);
+ local_irq_restore(flags);
wd33c93_execute(instance);
break;

@@ -1228,7 +1304,7 @@
else
cmd->result = cmd->SCp.Status | (cmd->SCp.Message << 8);
cmd->scsi_done(cmd);
- restore_flags(flags);
+ local_irq_restore(flags);
break;
case S_PRE_TMP_DISC:
case S_RUNNING_LEVEL2:
@@ -1693,7 +1769,7 @@
return 1;
}

-__setup("wd33c93", wd33c93_setup);
+__setup("wd33c93=", wd33c93_setup);


/* check_setup_args() returns index if key found, 0 if not
@@ -1831,10 +1907,12 @@


{ unsigned long flags;
- save_flags(flags);
- cli();
+ //save_flags(flags);
+ //cli();
+ spin_lock_irqsave(&wd_lock, flags);
reset_wd33c93(instance);
- restore_flags(flags);
+ //restore_flags(flags);
+ spin_unlock_irqrestore(&wd_lock, flags);
}

printk("wd33c93-%d: chip=%s/%d no_sync=0x%x no_dma=%d",instance->host_no,
@@ -1932,8 +2010,9 @@
return len;
}

- save_flags(flags);
- cli();
+ //save_flags(flags);
+ //cli();
+ spin_lock_irqsave(&wd_lock, flags);
bp = buf;
*bp = '\0';
if (hd->proc & PR_VERSION) {
@@ -2008,7 +2087,8 @@
}
}
strcat(bp,"\n");
- restore_flags(flags);
+ //restore_flags(flags);
+ spin_unlock_irqrestore(&wd_lock, flags);
*start = buf;
if (stop) {
stop = 0;
diff -urN linux/drivers/scsi/wd33c93.h linux98/drivers/scsi/wd33c93.h
--- linux/drivers/scsi/wd33c93.h Sat Oct 12 13:21:35 2002
+++ linux98/drivers/scsi/wd33c93.h Sat Oct 12 14:18:53 2002
@@ -186,8 +186,13 @@

/* This is what the 3393 chip looks like to us */
typedef struct {
+#if defined(CONFIG_SCSI_PC980155) || defined(CONFIG_SCSI_PC980155_MODULE)
+ volatile unsigned int *SASR;
+ volatile unsigned int *SCMD;
+#else
volatile unsigned char *SASR;
volatile unsigned char *SCMD;
+#endif
} wd33c93_regs;


diff -urN linux/include/scsi/scsicam.h linux98/include/scsi/scsicam.h
--- linux/include/scsi/scsicam.h Thu Jul 25 06:03:26 2002
+++ linux98/include/scsi/scsicam.h Fri Jul 26 11:32:39 2002
@@ -12,8 +12,13 @@

#ifndef SCSICAM_H
#define SCSICAM_H
+#include <linux/config.h>
extern int scsicam_bios_param (Disk *disk, struct block_device *bdev, int *ip);
extern int scsi_partsize(unsigned char *buf, unsigned long capacity,
unsigned int *cyls, unsigned int *hds, unsigned int *secs);
extern unsigned char *scsi_bios_ptable(struct block_device *bdev);
+#ifdef CONFIG_PC9800
+extern int pc9800_scsi_bios_param(Disk *disk, struct block_device *bdev,
+ int *ip);
+#endif
#endif /* def SCSICAM_H */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2005-03-22 13:30    [W:0.062 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site