lkml.org 
[lkml]   [2002]   [Jan]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: NIC lockup in 2.4.17 (SMP/APIC/Intel 82557)

The box is an Abit BP6 with Dual Celerons 433 and 192 Mb RAM. No
PCI-Riser cards. It is connected at 100 Mbit full duplex to a 100
Mbit switch. APIC is enabled. No kind of power management is enabled.

Below is my /proc/interrupts, lspci -vx and dmesg output.

Regards,
- Robbert



radium:/# cat /proc/interrupts
CPU0 CPU1
0: 2944301 2940065 IO-APIC-edge timer
1: 39 41 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
4: 3074 3208 IO-APIC-edge serial
8: 2 0 IO-APIC-edge rtc
14: 20 29 IO-APIC-edge ide0
17: 627932 628166 IO-APIC-level eth0
18: 121201 121973 IO-APIC-level ide2
19: 522304 521928 IO-APIC-level es1371
NMI: 0 0
LOC: 5884708 5884706
ERR: 170
MIS: 0

radium:/# lspci -vx
00:00.0 Host bridge: Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge (rev
03)
Flags: bus master, medium devsel, latency 32
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
00: 86 80 90 71 06 00 10 22 03 00 00 06 00 20 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Intel Corp. 440BX/ZX - 82443BX/ZX AGP bridge (rev 03)
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: d4000000-d7ffffff
Prefetchable memory behind bridge: d8000000-d8ffffff
00: 86 80 91 71 07 01 20 02 03 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 a0 22
20: 00 d4 f0 d7 00 d8 f0 d8 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 00
00:07.0 ISA bridge: Intel Corp. 82371AB PIIX4 ISA (rev 02)
Flags: bus master, medium devsel, latency 0
00: 86 80 10 71 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01) (prog-if 80
[Master])
Flags: bus master, medium devsel, latency 32
I/O ports at f000 [size=16]
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:07.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01) (prog-if 00
[UHCI])
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at c000 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0c 04 00 00

00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 02)
Flags: medium devsel, IRQ 9
00: 86 80 13 71 03 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:09.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Flags: bus master, slow devsel, latency 32, IRQ 19
I/O ports at c400 [size=64]
Capabilities: [dc] Power Management version 1
00: 74 12 71 13 05 01 10 34 06 00 01 04 00 20 00 00
10: 01 c4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 74 12 71 13
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0c 01 0c 80

00:0d.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 09)
Subsystem: Intel Corp.: Unknown device 0011
Flags: bus master, medium devsel, latency 32, IRQ 17
Memory at da020000 (32-bit, non-prefetchable) [size=4K]
I/O ports at c800 [size=64]
Memory at da000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
00: 86 80 29 12 07 00 90 02 09 00 00 02 08 20 00 00
10: 00 00 02 da 01 c8 00 00 00 00 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 11 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 08 38
00:13.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366
/ HPT370 (rev 01)
Flags: bus master, medium devsel, latency 120, IRQ 18
I/O ports at cc00 [size=8]
I/O ports at d000 [size=4]
I/O ports at d400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
00: 03 11 04 00 05 00 00 02 01 00 80 01 08 78 80 00
10: 01 cc 00 00 01 d0 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 08 08

00:13.1 Unknown mass storage controller: Triones Technologies, Inc. HPT366
/ HPT370 (rev 01)
Flags: bus master, medium devsel, latency 120, IRQ 18
I/O ports at d800 [size=8]
I/O ports at dc00 [size=4]
I/O ports at e000 [size=256]
00: 03 11 04 00 07 00 00 02 01 00 80 01 08 78 80 00
10: 01 d8 00 00 01 dc 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 08 08

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev
01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 AGP
Flags: bus master, medium devsel, latency 32, IRQ 16
Memory at d8000000 (32-bit, prefetchable) [size=16M]
Memory at d4000000 (32-bit, non-prefetchable) [size=16K]
Memory at d5000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Capabilities: [f0] AGP version 1.0
00: 2b 10 21 05 07 00 90 02 01 00 00 03 08 20 00 00
10: 08 00 00 d8 00 00 00 d4 00 00 00 d5 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 03 ff
30: 00 00 00 00 dc 00 00 00 00 00 00 00 09 01 10 20
radium:/# cat /var/log/dmesg
Linux version 2.4.18-pre7-ac1 (root@radium) (gcc version 2.95.4 (Debian
prerelease)) #1 SMP Thu Jan 31 01:06:59 CET 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000c000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
found SMP MP-table at 000f5ae0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 49152
zone(0): 4096 pages.
zone(1): 45056 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #1 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: auto BOOT_IMAGE=Linux ro root=2101
Initializing CPU#0
Detected 434.324 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 865.07 BogoMIPS
Memory: 191360k/196608k available (1316k kernel code, 4864k reserved, 383k
data, 240k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU0: Intel Celeron (Mendocino) stepping 05
per-CPU timeslice cutoff: 365.86 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 868.35 BogoMIPS
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU1: Intel Celeron (Mendocino) stepping 05
Total of 2 processors activated (1733.42 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-9, 2-10, 2-11, 2-12, 2-20, 2-21, 2-22, 2-23
not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 19.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 003 03 0 0 0 0 0 1 1 71
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
10 003 03 1 1 0 1 0 1 1 89
11 003 03 1 1 0 1 0 1 1 91
12 003 03 1 1 0 1 0 1 1 99
13 003 03 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 434.3005 MHz.
..... host bus clock speed is 66.8152 MHz.
cpu: 0, clocks: 668152, slice: 222717
CPU0<T0:668144,T1:445424,D:3,S:222717,C:668152>
cpu: 1, clocks: 668152, slice: 222717
CPU1<T0:668144,T1:222704,D:6,S:222717,C:668152>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I9,P0) -> 19
PCI->APIC IRQ transform: (B0,I13,P0) -> 17
PCI->APIC IRQ transform: (B0,I19,P0) -> 18
PCI->APIC IRQ transform: (B0,I19,P1) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IA-32 Microcode Update Driver: v1.09 <tigran@veritas.com>
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
Journalled Block Device driver loaded
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Legacy device
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-proc.o version 2.6.1 (20010825)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
lp0: using parport0 (polling).
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
HPT366: onboard version of chipset, pin1=1 pin2=2
HPT366: IDE controller on PCI bus 00 dev 98
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:DMA, hdf:pio
HPT366: IDE controller on PCI bus 00 dev 99
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide3: BM-DMA at 0xe000-0xe007, BIOS settings: hdg:pio, hdh:pio
hda: Maxtor 91728D8, ATA DISK drive
hde: ST38421A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xcc00-0xcc07,0xd002 on irq 18
hda: 33750864 sectors (17280 MB) w/512KiB Cache, CHS=2100/255/63, UDMA(33)
hde: 16498944 sectors (8447 MB) w/256KiB Cache, CHS=16368/16/63, UDMA(66)
Partition check:
hda: hda1
hde: [PTBL] [1027/255/63] hde1 hde2 < hde5 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw@saw.sw.com.sg> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:D0:B7:E8:A2:02, IRQ 17.
Board assembly 749658-005, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xdbd8681d).
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
PPP BSD Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 150M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xd0000000
[drm] AGP 0.99 on Intel 440BX @ 0xd0000000 64MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
es1371: version v0.30 time 01:10:14 Jan 31 2002
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x06
es1371: found es1371 rev 6 at io 0xc400 irq 19
es1371: features: joystick 0x0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
ip_conntrack (1536 buckets, 12288 max)
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 240k freed
Adding Swap: 72256k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.



On Thu, 31 Jan 2002, Ben Greear wrote:

> What does the rest of the hardware-config look like? Is
> the NIC attached to a 10bt hub? Are you using PCI-Riser
> cards?
>
> Ben Greear <greearb@candelatech.com> <Ben_Greear AT excite.com>
> President of Candela Technologies Inc http://www.candelatech.com
> ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear
>
>
>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:16    [from the cache]
©2003-2011 Jasper Spaans