lkml.org 
[lkml]   [2001]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [eepro100] eepro100 driver (2.4 kernel) fails with S2080 Tomcati815t motherboard.
Interestingly enough, when I manually set a MAC it seems to pass traffic,
at least at low speeds. I'm about to crank it up a bit to see what
falls out :)

(Working fine at 10Mbps (about 4200 packets-per-second..)


Donald Becker wrote:
>
> On Tue, 18 Sep 2001, Ben Greear wrote:
>
> > I have a Tyan motherboard (S2080 Tomcat i815t) with 2 built-in NICs.
> >
> > The manual claims this:
> >
> > "One Intel 82559 LAN controller
> > One ICH2 LAN controller"
> >
> > Seems that the eepro driver tries to bring up both of
> > them, and fails to read the eeprom on the second one it
> > scans. One visible result is that the MAC is all FF's.
>
> Does the diagnostic program correctly read the EEPROM on both cards?
> If so, my driver release should work with the cards.
>

It doesn't seem to...


[root@lanf1 /root]# eepro100-diag -aaeemmf -#1
eepro100-diag.c:v2.02 7/19/2000 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a Intel i82562 EEPro100 adapter at 0xdd80.
i82557 chip registers at 0xdd80:
0c000050 0f162000 00000000 00080002 1be7ffff 00000600
No interrupt sources are pending.
The transmit unit state is 'Suspended'.
The receive unit state is 'Ready'.
This status is normal for an activated but idle interface.
The Command register has an unprocessed command 0c00(?!).
EEPROM contents, size 256x16:
00: ffff ffff ffff ffff ffff ffff ffff ffff
0x08: ffff ffff ffff ffff ffff ffff ffff ffff
0x10: ffff ffff ffff ffff ffff ffff ffff ffff
0x18: ffff ffff ffff ffff ffff ffff ffff ffff
0x20: ffff ffff ffff ffff ffff ffff ffff ffff
0x28: ffff ffff ffff ffff ffff ffff ffff ffff
0x30: ffff ffff ffff ffff ffff ffff ffff ffff
0x38: ffff ffff ffff ffff ffff ffff ffff ffff
0x40: ffff ffff ffff ffff ffff ffff ffff ffff
0x48: ffff ffff ffff ffff ffff ffff ffff ffff
0x50: ffff ffff ffff ffff ffff ffff ffff ffff
0x58: ffff ffff ffff ffff ffff ffff ffff ffff
0x60: ffff ffff ffff ffff ffff ffff ffff ffff
0x68: ffff ffff ffff ffff ffff ffff ffff ffff
0x70: ffff ffff ffff ffff ffff ffff ffff ffff
0x78: ffff ffff ffff ffff ffff ffff ffff ffff
0x80: ffff ffff ffff ffff ffff ffff ffff ffff
0x88: ffff ffff ffff ffff ffff ffff ffff ffff
0x90: ffff ffff ffff ffff ffff ffff ffff ffff
0x98: ffff ffff ffff ffff ffff ffff ffff ffff
0xa0: ffff ffff ffff ffff ffff ffff ffff ffff
0xa8: ffff ffff ffff ffff ffff ffff ffff ffff
0xb0: ffff ffff ffff ffff ffff ffff ffff ffff
0xb8: ffff ffff ffff ffff ffff ffff ffff ffff
0xc0: ffff ffff ffff ffff ffff ffff ffff ffff
0xc8: ffff ffff ffff ffff ffff ffff ffff ffff
0xd0: ffff ffff ffff ffff ffff ffff ffff ffff
0xd8: ffff ffff ffff ffff ffff ffff ffff ffff
0xe0: ffff ffff ffff ffff ffff ffff ffff ffff
0xe8: ffff ffff ffff ffff ffff ffff ffff ffff
0xf0: ffff ffff ffff ffff ffff ffff ffff ffff
0xf8: ffff ffff ffff ffff ffff ffff ffff ffff
***** The EEPROM checksum is INCORRECT! *****
The checksum is 0xFF00, it should be 0xBABA!
Intel EtherExpress Pro 10/100 EEPROM contents:
Station address FF:FF:FF:FF:FF:FF.
Board assembly ffffff-255, Physical connectors present: RJ45 BNC AUI MII
Primary interface chip i82555 PHY #-1.
Secondary interface chip i82555, PHY -1.
Baseline value of MII status register is 0000.

[root@lanf1 /root]#

> > eth0: Intel Corporation 82557 [Ethernet Pro 100] (#3), 00:E0:81:03:B9:7B, IRQ 10.
> > eth1: Intel Corporation 82557 [Ethernet Pro 100] (#2), 00:90:27:65:39:1B, IRQ 3.
> > eth2: Intel Corporation 82557 [Ethernet Pro 100], 00:90:27:65:37:8A, IRQ 9.
> > eth3: Invalid EEPROM checksum 0xff00, check settings before activating this device!
> > eth3: OEM i82557/i82558 10/100 Ethernet, FF:FF:FF:FF:FF:FF, IRQ 11.
>
> > [root@lanf2 /root]# eepro100-diag -aaeemmf eth3
>
> The diagnostic does not (and cannot) know which card is "eth3".
> (Consider the case where no driver is loaded.)

I wish it would have complained about me sending it eth3 then, so
I would have known!

>
> You must specify the interface to examine with e.g. "-#3"

Thanks,
Ben


>
> Donald Becker becker@scyld.com
> Scyld Computing Corporation http://www.scyld.com
> 410 Severn Ave. Suite 210 Second Generation Beowulf Clusters
> Annapolis MD 21403 410-990-9993
>
> _______________________________________________
> eepro100 mailing list
> eepro100@scyld.com
> http://www.scyld.com/mailman/listinfo/eepro100

--
Ben Greear <greearb@candelatech.com> <Ben_Greear@excite.com>
President of Candela Technologies Inc http://www.candelatech.com
ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:03    [W:0.121 / U:0.624 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site