lkml.org 
[lkml]   [2001]   [Aug]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subjectaic7xxx errors with 2.4.8-ac7 on 440gx mobo
Hi, 2.4.8 and 2.4.9 have no problems compiling and booting on a P3 500
440GX mobo (APIC not compiled in the kernel)

With 2.4.8-ac7, I get SCSI errors and the kernel fails to boot. If I
compile with APIC enabled and APIC on UP also enabled, it boots
cleanly

booting with append="noapic", gives the same errors


SCSI subsystem driver Revision: 1.00
PCI: Assigned IRQ 11 for device 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.1
PCI: Found IRQ 11 for device 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.0

scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec aic7896/97 Ultra2 SCSI adapter>
aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs

scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec aic7896/97 Ultra2 SCSI adapter>
aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/255 SCBs

scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command already completed
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 8195
scsi0:0:0:0: Attempting to queue a TARGET RESET message
aic7xxx_dev_reset returns 8195
Recovery SCB completes
scsi0:0:0:0: Attempting to queue an ABORT message
ahc_intr: HOST_MSG_LOOP bad phase 0x0
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 8194
scsi: device set offline - not ready or command retry failed after bus reset: host 0 channel 0 id 0 lun 0
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0:0:1:0: Command already completed
aic7xxx_abort returns 8194
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0:0:1:0: Command already completed
aic7xxx_abort returns 8194
scsi0:0:1:0: Attempting to queue a TARGET RESET message
scsi0:0:1:0: Is not an active device
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0:0:1:0: Command already completed
aic7xxx_abort returns 8194

Regards, Yusuf
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:57    [W:0.256 / U:2.804 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site