lkml.org 
[lkml]   [2001]   [Aug]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: PCMCIA PCI interrupt problem with Medion 9888 / TI 1131
Date
From
> 
> Hi,
>
> I have a problem getting 2.4.x kernels running, it seems that
> there is a problem with PCI interrupt allocation.
> The machine is a Medion 9888 (Aldi notebook of christmas 1998),
> which is basically a Twinhead EX2.
> The following is copied by hand from a photo
> (it didn't make it to the log for obvious reasons):
>
> Starting PCMCIA services: modulesLinux PCMCIA Card Services 3.1.28
> kernel build: 2.4.8 #1 Sun Aug 12 19:06:35 CEST 2001
> options: [pci] [cardbus] [apm]
> Intel PCIC probe: <6>PCI: Assigned IRQ 13 for device 00:0a.0
> PCI: Assigned IRQ 14 for device 00:0a.1
>
> TI 1131 rev 01 PCI-to-CardBus at slot 00:0a, mem 0x10000000=20
> host opts [0]: [ring] [clkrun irq 12] [pci + serial irq] [pci irq 1=
> 3] [lat 168/176] [bus 1/4]
> host opts [1]: [ring] [clkrun irq 12] [pci + serial irq] [pci irq 1=
> 4] [lat 168/176] [bus 5/8]
> PCI irq test 13 failed
> ISA irqs (scanned) =3D 3,4,7,10,11,15 status change on irq 15
> cardmgr.
>
> ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> hda: lost interrupt
> ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> hda: lost interrupt
> ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> hda: lost interrupt
>
>
> The problem exists at least since 2.4.6 and pcmcia-cs-3.1.26.
> and it for the yenta driver in the kernel as well as the i82365
> in pcmcia-cs.
>
> It works for 2.2.19 with pcmcia-cs 3.1.x, there the interrupts
> for the slots are disabled:
>
> Aug 13 13:05:32 localhost kernel: Linux PCMCIA Card Services 3.1.26
> Aug 13 13:05:32 localhost kernel: kernel build: 2.2.19 unknown
> Aug 13 13:05:32 localhost kernel: options: [pci] [cardbus] [apm]
> Aug 13 13:05:32 localhost kernel: PCI routing table version 1.0 at 0xfd=
> f90
> Aug 13 13:05:32 localhost kernel: Intel PCIC probe:=20
> Aug 13 13:05:32 localhost kernel: TI 1131 rev 01 PCI-to-CardBus at sl=
> ot 00:0a, mem 0x68000000
> Aug 13 13:05:32 localhost kernel: host opts [0]: [ring] [clkrun irq=
> 12] [pci + serial irq] [no pci irq] [lat 168/176] [bus 32/34]
> Aug 13 13:05:32 localhost kernel: host opts [1]: [ring] [clkrun irq=
> 12] [pci + serial irq] [no pci irq] [lat 168/176] [bus 35/37]
> Aug 13 13:05:32 localhost kernel: ISA irqs (scanned) =3D 3,4,7,10,1=
> 1,15 polling interval =3D 1000 ms
> Aug 13 13:05:32 localhost cardmgr[198]: starting, version is 3.1.28
> Aug 13 13:05:32 localhost cardmgr[198]: watching 2 sockets
> Aug 13 13:05:32 localhost cardmgr[198]: Card Services release does not =
> match
> Aug 13 13:05:32 localhost cardmgr[198]: initializing socket 1
> Aug 13 13:05:32 localhost kernel: cs: memory probe 0xa0000000-0xa0fffff=
> f: clean.
> Aug 13 13:05:32 localhost cardmgr[198]: socket 1: D-Link DE-660 Etherne=
> t
> Aug 13 13:05:33 localhost cardmgr[198]: executing: 'modprobe 8390'
> Aug 13 13:05:33 localhost cardmgr[198]: executing: 'modprobe pcnet_cs'
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0100-0x04ff: excl=
> uding 0x300-0x307 0x378-0x37f 0x388-0x38f 0x398-0x39f 0x4d0-0x4d7
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0308-0x0377: clea=
> n.
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0380-0x0387: clea=
> n.
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0390-0x0397: clea=
> n.
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x03a0-0x04cf: clea=
> n.
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x04d8-0x04ff: clea=
> n.
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0800-0x08ff: excl=
> uding 0x800-0x807
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clea=
> n.
> Aug 13 13:05:33 localhost kernel: cs: IO port probe 0x0c00-0x0cff: excl=
> uding 0xcf8-0xcff
> Aug 13 13:05:33 localhost kernel: eth0: NE2000 Compatible: io 0x320, ir=
> q 10, hw_addr 00:80:C8:8F:08:60
>
> I tried to disable the interrupts using module options,
> but this seems to be possible only for the card change interrupt,
> and that one is not the problem.
>
> Any hints?
>
> J=FCrgen
>
> --=20
> J=FCrgen Stuber <stuber@loria.fr>
> http://www.loria.fr/~stuber/
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel"=
> in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:57    [W:6.852 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site