Messages in this thread | | | Date | Fri, 29 Jun 2001 16:04:59 +0200 (CEST) | From | Tobias Ringstrom <> | Subject | WOL with 3c59x and 2.4.6-pre6 breaks WOL |
| |
I just tried 2.4.6-pre6 this morning, and found out that when I enable WOL (using enable_wol=1), my 3c905c-tx does not work at all any more. It worked just fine with 2.4.5. Without enable_wol=1, I have no problems.
It is my guess that this is very easy to reproduce, but if not, please ask me for more details. I'm attaching the dmesg output. I'll be gone until monday.
/Tobias
Linux version 2.4.6-pre6 (root@igor.prodako.se) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-85)) #2 Thu Jun 28 17:45:38 CEST 2001 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e800 (usable) BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000ffec000 (usable) BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data) BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved) BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) On node 0 totalpages: 65516 zone(0): 4096 pages. zone(1): 61420 pages. zone(2): 0 pages. Kernel command line: BOOT_IMAGE=linux ro root=2103 BOOT_FILE=/boot/vmlinuz hdc=ide-scsi 1 ide_setup: hdc=ide-scsi Initializing CPU#0 Detected 1009.014 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 2011.95 BogoMIPS Memory: 255060k/262064k available (1329k kernel code, 6612k reserved, 454k data, 220k init, 0k highmem) Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000 CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000 CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000 CPU: AMD Athlon(tm) Processor stepping 02 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent PCI: Using IRQ router VIA [1106/0686] at 00:04.0 PCI: Found IRQ 9 for device 00:09.0 PCI: Sharing IRQ 9 with 00:04.2 PCI: Sharing IRQ 9 with 00:04.3 PCI: Sharing IRQ 9 with 00:0d.0 Found VT82C686A, not applying VIA latency patch. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14) Starting kswapd v1.8 parport0: PC-style at 0x378 [PCSPP(,...)] parport_pc: Via 686A parallel port: io=0x378 pty: 256 Unix98 ptys configured Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10d ppdev: user-space parallel port driver block: queued sectors max/low 169437kB/56479kB, 512 slots per queue Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 21 VP_IDE: chipset revision 16 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:04.1 ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio PDC20265: IDE controller on PCI bus 00 dev 88 PCI: Found IRQ 10 for device 00:11.0 PDC20265: chipset revision 2 PDC20265: not 100% native mode: will probe irqs later PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. ide2: BM-DMA at 0x7800-0x7807, BIOS settings: hde:DMA, hdf:DMA ide3: BM-DMA at 0x7808-0x780f, BIOS settings: hdg:pio, hdh:DMA hda: HITACHI DVD-ROM GD-7500, ATAPI CD/DVD-ROM drive hdc: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive hde: IBM-DTLA-307060, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide2 at 0x9000-0x9007,0x8802 on irq 10 hde: 120103200 sectors (61493 MB) w/1916KiB Cache, CHS=119150/16/63, UDMA(100) hda: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Partition check: hde: [PTBL] [7476/255/63] hde1 hde2 hde3 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) PPP generic driver version 2.4.1 PPP Deflate Compression module registered SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.08 Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray Creative EMU10K1 PCI Audio Driver, version 0.7, 17:36:57 Jun 28 2001 PCI: Enabling device 00:09.0 (0004 -> 0005) PCI: Found IRQ 9 for device 00:09.0 PCI: Sharing IRQ 9 with 00:04.2 PCI: Sharing IRQ 9 with 00:04.3 PCI: Sharing IRQ 9 with 00:0d.0 emu10k1: EMU10K1 rev 8 model 0x8027 found, IO at 0xa400-0xa41f, IRQ 9 usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.259 $ time 17:37:11 Jun 28 2001 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 9 for device 00:04.2 PCI: Sharing IRQ 9 with 00:04.3 PCI: Sharing IRQ 9 with 00:09.0 PCI: Sharing IRQ 9 with 00:0d.0 usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 9 for device 00:04.3 PCI: Sharing IRQ 9 with 00:04.2 PCI: Sharing IRQ 9 with 00:09.0 PCI: Sharing IRQ 9 with 00:0d.0 usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 9 usb-uhci.c: Detected 2 ports hub.c: USB new device connect on bus1/2, assigned device number 2 usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 4 ports detected hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.251:USB Universal Host Controller Interface driver usb.c: registered new driver hid hid.c: v1.16:USB HID support drivers mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 16384) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 220k freed hub.c: USB new device connect on bus2/2, assigned device number 2 hub.c: USB hub found hub.c: 4 ports detected Adding Swap: 208836k swap-space (priority -1) PCI: Enabling device 00:0a.0 (0014 -> 0017) PCI: Assigned IRQ 5 for device 00:0a.0 3c59x.c:LK1.1.15 6 June 2001 Donald Becker and others. http://www.scyld.com/network/vortex.html See Documentation/networking/vortex.txt 00:0a.0: 3Com PCI 3c905C Tornado at 0x9800, 00:01:02:dc:f6:c6, IRQ 5 product code 464a rev 00.13 date 10-09-00 Full duplex capable 8K byte-wide RAM 5:3 Rx:Tx split, 100baseTX interface. Enabling bus-master transmits and whole-frame receives. 00:0a.0: scatter/gather enabled. h/w checksums enabled eth0: using default media 100baseTX eth0: command 0x5800 did not complete! Status=0xffff eth0: command 0x2800 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff eth0: command 0x3002 did not complete! Status=0xffff NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status ff status ffff. diagnostics: net ffff media ffff dma ffffffff. eth0: Transmitter encountered 16 collisions -- network cable problem? eth0: Interrupt posted but not delivered -- IRQ blocked by another device? Flags; bus-master 1, dirty 0(0) current 16(0) Transmit list ffffffff vs. cf972200. eth0: command 0x3002 did not complete! Status=0xffff 0: @cf972200 length 8000002a status 0000002a 1: @cf972240 length 8000002a status 0000002a 2: @cf972280 length 8000002a status 0000002a 3: @cf9722c0 length 8000002a status 0000002a 4: @cf972300 length 8000002a status 0000002a 5: @cf972340 length 8000002a status 0000002a 6: @cf972380 length 8000002a status 0000002a 7: @cf9723c0 length 8000002a status 0000002a 8: @cf972400 length 8000002a status 0000002a 9: @cf972440 length 8000002a status 0000002a 10: @cf972480 length 8000002a status 0000002a 11: @cf9724c0 length 8000002a status 0000002a 12: @cf972500 length 8000002a status 0000002a 13: @cf972540 length 8000002a status 0000002a 14: @cf972580 length 8000002a status 8000002a 15: @cf9725c0 length 8000002a status 8000002a eth0: command 0x5800 did not complete! Status=0xffff eth0: Resetting the Tx ring pointer. NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status ff status ffff. diagnostics: net ffff media ffff dma ffffffff. eth0: Transmitter encountered 16 collisions -- network cable problem? eth0: Interrupt posted but not delivered -- IRQ blocked by another device? Flags; bus-master 1, dirty 0(0) current 16(0) Transmit list ffffffff vs. cf972200. eth0: command 0x3002 did not complete! Status=0xffff 0: @cf972200 length 8000002a status 0000002a 1: @cf972240 length 8000002a status 0000002a 2: @cf972280 length 8000002a status 0000002a 3: @cf9722c0 length 8000002a status 0000002a 4: @cf972300 length 8000002a status 0000002a 5: @cf972340 length 8000002a status 0000002a 6: @cf972380 length 8000002a status 0000002a 7: @cf9723c0 length 8000002a status 0000002a 8: @cf972400 length 8000002a status 0000002a 9: @cf972440 length 8000002a status 0000002a 10: @cf972480 length 8000002a status 0000002a 11: @cf9724c0 length 8000002a status 0000002a 12: @cf972500 length 8000002a status 0000002a 13: @cf972540 length 8000002a status 0000002a 14: @cf972580 length 8000002a status 8000002a 15: @cf9725c0 length 8000002a status 8000002a eth0: command 0x5800 did not complete! Status=0xffff eth0: Resetting the Tx ring pointer. NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status ff status ffff. diagnostics: net ffff media ffff dma ffffffff. eth0: Transmitter encountered 16 collisions -- network cable problem? eth0: Interrupt posted but not delivered -- IRQ blocked by another device? Flags; bus-master 1, dirty 0(0) current 16(0) Transmit list ffffffff vs. cf972200. eth0: command 0x3002 did not complete! Status=0xffff 0: @cf972200 length 8000002a status 0000002a 1: @cf972240 length 8000002a status 0000002a 2: @cf972280 length 8000002a status 0000002a 3: @cf9722c0 length 8000002a status 0000002a 4: @cf972300 length 8000002a status 0000002a 5: @cf972340 length 8000002a status 0000002a 6: @cf972380 length 8000002a status 0000002a 7: @cf9723c0 length 8000002a status 0000002a 8: @cf972400 length 8000002a status 0000002a 9: @cf972440 length 8000002a status 0000002a 10: @cf972480 length 8000002a status 0000002a 11: @cf9724c0 length 8000002a status 0000002a 12: @cf972500 length 8000002a status 0000002a 13: @cf972540 length 8000002a status 0000002a 14: @cf972580 length 8000002a status 8000002a 15: @cf9725c0 length 8000002a status 8000002a eth0: command 0x5800 did not complete! Status=0xffff eth0: Resetting the Tx ring pointer. NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status ff status ffff. diagnostics: net ffff media ffff dma ffffffff. eth0: Transmitter encountered 16 collisions -- network cable problem? eth0: Interrupt posted but not delivered -- IRQ blocked by another device? Flags; bus-master 1, dirty 0(0) current 16(0) Transmit list ffffffff vs. cf972200. eth0: command 0x3002 did not complete! Status=0xffff 0: @cf972200 length 8000002a status 0000002a 1: @cf972240 length 8000002a status 0000002a 2: @cf972280 length 8000002a status 0000002a 3: @cf9722c0 length 8000002a status 0000002a 4: @cf972300 length 8000002a status 0000002a 5: @cf972340 length 8000002a status 0000002a 6: @cf972380 length 8000002a status 0000002a 7: @cf9723c0 length 8000002a status 0000002a 8: @cf972400 length 8000002a status 0000002a 9: @cf972440 length 8000002a status 0000002a 10: @cf972480 length 8000002a status 0000002a 11: @cf9724c0 length 8000002a status 0000002a 12: @cf972500 length 8000002a status 0000002a 13: @cf972540 length 8000002a status 0000002a 14: @cf972580 length 8000002a status 8000002a 15: @cf9725c0 length 8000002a status 8000002a eth0: command 0x5800 did not complete! Status=0xffff eth0: Resetting the Tx ring pointer. NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status ff status ffff. diagnostics: net ffff media ffff dma ffffffff. eth0: Transmitter encountered 16 collisions -- network cable problem? eth0: Interrupt posted but not delivered -- IRQ blocked by another device? Flags; bus-master 1, dirty 0(0) current 16(0) Transmit list ffffffff vs. cf972200. eth0: command 0x3002 did not complete! Status=0xffff 0: @cf972200 length 8000002a status 0000002a 1: @cf972240 length 8000002a status 0000002a 2: @cf972280 length 8000002a status 0000002a 3: @cf9722c0 length 8000002a status 0000002a 4: @cf972300 length 8000002a status 0000002a 5: @cf972340 length 8000002a status 0000002a 6: @cf972380 length 8000002a status 0000002a 7: @cf9723c0 length 8000002a status 0000002a 8: @cf972400 length 8000002a status 0000002a 9: @cf972440 length 8000002a status 0000002a 10: @cf972480 length 8000002a status 0000002a 11: @cf9724c0 length 8000002a status 0000002a 12: @cf972500 length 8000002a status 0000002a 13: @cf972540 length 8000002a status 0000002a 14: @cf972580 length 8000002a status 8000002a 15: @cf9725c0 length 8000002a status 8000002a eth0: command 0x5800 did not complete! Status=0xffff eth0: Resetting the Tx ring pointer.
| |