Messages in this thread |  | | Date | Sun, 6 May 2001 13:51:39 -0400 | From | Ignacio Monge <> | Subject | Re: 8139too bug in 2.4.4 (2.4.3?) & VIA 686a |
| |
En Sun, 6 May 2001 13:03:03 -0400 Ignacio Monge <ignaciomonge@navegalia.com> escribió:
> > I've compiled 2.4.3mdk-25 source with Athlon optimizations, and the > problem still happens. > > eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF > inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:4294967221 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:100 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:11 Base address:0x9000 > > Look at the HWaddr. With default kernel (not compiled), I haven't this > problem and my ethernet card goes well and the HWaddr is: ·"HWaddr > 00:E0:29:9A:CB:62 ". And I'm sure after reboot I *MUST* restore all the > values of my BIOS setup. Believe me, I know. :( > > > Here is the output of dmesg when loading the 81389too module: > > Assertion failed! ioaddr != NULL,8139too.c,rtl8139_init_one,line=927 > eth0: SMC1211TX EZCard 10/100 (RealTek RTL8139) at 0x9000, > ff:ff:ff:ff:ff:ff, IRQ 11 > eth0: Identified 8139 chip type 'RTL-8139C' > eth0: Setting 100mbps half-duplex based on auto-negotiated partner > ability > ffff. > > "Assertion failed! ioaddr != NULL,8139too.c,rtl8139_init_one,line=927"? > What is this? Is this the cause of the bug? > > Now the lspci -vv: > > 00:0c.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX > (rev 10) > Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- > <MAbort- >SERR- <PERR- > Latency: 32 (8000ns min, 16000ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at 9000 [size=256] > Region 1: Memory at da800000 (32-bit, non-prefetchable) [size=256] > Expansion ROM at <unassigned> [disabled] [size=64K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > I hope these lines can help.
ADDON:
Dmesg: [... NETDEV WATCHDOG: eth0: transmit timed out eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is ffffffff. (queue head) eth0: Tx descriptor 1 is ffffffff. eth0: Tx descriptor 2 is ffffffff. eth0: Tx descriptor 3 is ffffffff. eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability ffff. probable hardware bug: clock timer configuration lost - probably a VIA686a motherboard. probable hardware bug: restoring chip configuration.
...] - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
|  |