lkml.org 
[lkml]   [2001]   [Apr]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject2.4.3-ac14 deadlocks on PDC20265 w/o noautotune
Hello,

2.4.3-ac14 still deadlocks with PDC20265 (on ASUS A7V133) when using without
noautotune. System starts up, but lockups in few minutes with HDD led
burning. System is RedHat 7.1, but gcc-2.95.3 is used to compile the kernel.

dmesg and config attached.

Best regards,

- Jussi Laako

P.S. Just wondering why kernel reports MTRR as being type "Intel" when CPU
is Duron/800...

--
PGP key fingerprint: 3827 6A53 B7F9 180E D971 362B BB53 C8A1 B578 D249
Available at: ldap://certserver.pgp.comLinux version 2.4.3-ac14 (root@davinci) (gcc version 2.95.3 20010315 (release)) #1 Wed Apr 25 13:36:33 EEST 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007fec000 (usable)
BIOS-e820: 0000000007fec000 - 0000000007fef000 (ACPI data)
BIOS-e820: 0000000007fef000 - 0000000007fff000 (reserved)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 32748
zone(0): 4096 pages.
zone(1): 28652 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=2104 BOOT_FILE=/boot/vmlinuz ide0=noautotune ide1=noautotune ide2=noautotune ide3=noautotune panic=60
ide_setup: ide0=noautotune
ide_setup: ide1=noautotune
ide_setup: ide2=noautotune
ide_setup: ide3=noautotune
Initializing CPU#0
Detected 807.211 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1608.90 BogoMIPS
Memory: 126904k/130992k available (861k kernel code, 3696k reserved, 217k data, 188k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Duron(tm) Processor stepping 01
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
Applying VIA PCI latency patch.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 84280kB/28093kB, 256 slots per queue
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
PDC20265: IDE controller on PCI bus 00 dev 88
PCI: Found IRQ 10 for device 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0x7400-0x7407, BIOS settings: hde:DMA, hdf:DMA
ide3: BM-DMA at 0x7408-0x740f, BIOS settings: hdg:DMA, hdh:DMA
hda: SONY CDU4811, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307030, ATA DISK drive
hdf: IBM-DTLA-307030, ATA DISK drive
hdg: IBM-DTLA-307030, ATA DISK drive
hdh: IBM-DTLA-307030, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0x8800-0x8807,0x8402 on irq 10
ide3 at 0x8000-0x8007,0x7802 on irq 10
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
hdf: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
hdg: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
hdh: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
Partition check:
hde: [PTBL] [3737/255/63] hde1 hde2 hde3 hde4
hdf: unknown partition table
hdg: unknown partition table
hdh: unknown partition table
ACPI: APM is already active, exiting
raid5 personality registered
raid5: measuring checksumming speed
8regs : 1233.200 MB/sec
32regs : 1090.800 MB/sec
pII_mmx : 1889.600 MB/sec
p5_mmx : 2418.400 MB/sec
raid5: using function: p5_mmx (2418.400 MB/sec)
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 188k freed
Adding Swap: 265064k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 13:41:56 Apr 25 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:04.2
PCI: The same IRQ used for device 00:04.3
PCI: The same IRQ used for device 00:09.0
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:04.3
PCI: The same IRQ used for device 00:04.2
PCI: The same IRQ used for device 00:09.0
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
(read) hdf's sb offset: 30018176 [events: 00000022]
(read) hdg's sb offset: 30018176 [events: 00000022]
(read) hdh's sb offset: 30018176 [events: 00000022]
autorun ...
considering hdh ...
adding hdh ...
adding hdg ...
adding hdf ...
created md0
bind<hdf,1>
bind<hdg,2>
bind<hdh,3>
running: <hdh><hdg><hdf>
now!
hdh's event counter: 00000022
hdg's event counter: 00000022
hdf's event counter: 00000022
md: md0: raid array is not clean -- starting background reconstruction
md0: max total readahead window set to 512k
md0: 2 data-disks, max readahead per data-disk: 256k
raid5: device hdh operational as raid disk 2
raid5: device hdg operational as raid disk 1
raid5: device hdf operational as raid disk 0
raid5: allocated 3264kB for md0
raid5: raid level 5 set md0 active with 3 out of 3 devices, algorithm 2
raid5: raid set md0 not clean; reconstructing parity
RAID5 conf printout:
--- rd:3 wd:3 fd:0
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdf
disk 1, s:0, o:1, n:1 rd:1 us:1 dev:hdg
disk 2, s:0, o:1, n:2 rd:2 us:1 dev:hdh
RAID5 conf printout:
--- rd:3 wd:3 fd:0
disk 0, s:0, o:1, n:0 rd:0 us:1 dev:hdf
disk 1, s:0, o:1, n:1 rd:1 us:1 dev:hdg
disk 2, s:0, o:1, n:2 rd:2 us:1 dev:hdh
md: updating md0 RAID superblock on device
hdh [events: 00000023](write) hdh's sb offset: 30018176
md: syncing RAID array md0
md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 100000 KB/sec) for reconstruction.
md: using 124k window, over a total of 30018176 blocks.
hdg [events: 00000023](write) hdg's sb offset: 30018176
hdf [events: 00000023](write) hdf's sb offset: 30018176
.
... autorun DONE.
raid5: switching cache buffer size, 4096 --> 1024
raid5: switching cache buffer size, 1024 --> 4096
reiserfs: checking transaction log (device 09:00) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 15 for device 00:0a.0
PCI: Found IRQ 15 for device 00:0a.0
(scsi0) <Adaptec AIC-7860 Ultra SCSI host adapter> found at PCI 0/10/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Cables present (Int-50 NO, Ext-50 YES)
(scsi0) Downloading sequencer code... 436 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7860 Ultra SCSI host adapter>
Vendor: HP Model: C1537A Rev: L708
Type: Sequential-Access ANSI SCSI revision: 02
(scsi0:0:3:1) Synchronous at 10.0 Mbyte/sec, offset 15.
scsi : 0 hosts left.
Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
0x378: FIFO is 16 bytes
0x378: writeIntrThreshold is 8
0x378: readIntrThreshold is 8
0x378: PWord is 8 bits
0x378: Interrupts are ISA-Pulses
0x378: ECP port cfgA=0x10 cfgB=0x00
0x378: ECP settings irq=<none or set by other means> dma=<none or set by other means>
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,COMPAT,ECP]
parport0: cpp_daisy: aa5500ff(98)
parport0: assign_addrs: aa5500ff(98)
parport0: No more nibble data (0 bytes)
parport0: faking semi-colon
parport0: Printer, Hewlett-Packard HP LaserJet 4000 Series
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 15 for device 00:0a.0
PCI: Found IRQ 15 for device 00:0a.0
(scsi0) <Adaptec AIC-7860 Ultra SCSI host adapter> found at PCI 0/10/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Cables present (Int-50 NO, Ext-50 YES)
(scsi0) Downloading sequencer code... 436 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7860 Ultra SCSI host adapter>
Vendor: HP Model: C1537A Rev: L708
Type: Sequential-Access ANSI SCSI revision: 02
(scsi0:0:3:1) Synchronous at 10.0 Mbyte/sec, offset 15.
scsi : 0 hosts left.
PCI: Found IRQ 5 for device 00:09.0
PCI: The same IRQ used for device 00:04.2
PCI: The same IRQ used for device 00:04.3
3c59x.c:LK1.1.13 27 Jan 2001 Donald Becker and others. http://www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
eth0: 3Com PCI 3c905C Tornado at 0x9400, 00:01:02:dd:83:52, IRQ 5
product code 464a rev 00.13 date 10-10-00
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 782d.
Enabling bus-master transmits and whole-frame receives.
eth0: scatter/gather enabled. h/w checksums enabled
eth0: using NWAY device table, not 8
0x378: FIFO is 16 bytes
0x378: writeIntrThreshold is 8
0x378: readIntrThreshold is 8
0x378: PWord is 8 bits
0x378: Interrupts are ISA-Pulses
0x378: ECP port cfgA=0x10 cfgB=0x00
0x378: ECP settings irq=<none or set by other means> dma=<none or set by other means>
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,COMPAT,ECP]
parport0: cpp_daisy: aa5500ff(98)
parport0: assign_addrs: aa5500ff(98)
parport0: No more nibble data (0 bytes)
parport0: faking semi-colon
parport0: Printer, Hewlett-Packard HP LaserJet 4000 Series
lp0: using parport0 (interrupt-driven).
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
set_rtc_mmss: can't update from 0 to 59
md: md0: sync done.
raid5: resync finished.
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 15 for device 00:0a.0
PCI: Found IRQ 15 for device 00:0a.0
(scsi0) <Adaptec AIC-7860 Ultra SCSI host adapter> found at PCI 0/10/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Cables present (Int-50 NO, Ext-50 YES)
(scsi0) Downloading sequencer code... 436 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7860 Ultra SCSI host adapter>
Vendor: HP Model: C1537A Rev: L708
Type: Sequential-Access ANSI SCSI revision: 02
(scsi0:0:3:1) Synchronous at 10.0 Mbyte/sec, offset 15.
st: bufsize 32768, wrt 30720, max init. buffers 4, s/g segs 16.
Attached scsi tape st0 at scsi0, channel 0, id 3, lun 0
st0: Block limits 1 - 16777215 bytes.
scsi : 0 hosts left.
st: Unloaded.
[unhandled content-type:application/x-ns-proxy-autoconfig]
\
 
 \ /
  Last update: 2005-03-22 12:52    [W:0.057 / U:0.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site