lkml.org 
[lkml]   [2001]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subjectusb problems in 2.4.11
I'm having some odd usb "raced timeout" problems that just showed up in
2.4.11, it takes considerably longer to initialize the usb controller..
about 15 seconds as opposed to 1-2 seconds in 2.4.10. Everything appears to
function normally once the driver is loaded.

I have provided the dmesg, lsusb and lspci outputs.

--
Stephen
00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133] (rev 81)
Subsystem: Asustek Computer, Inc.: Unknown device 802c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f4800000-f5dfffff
Prefetchable memory behind bridge: f5f00000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: Asustek Computer, Inc.: Unknown device 802c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:04.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 03)
Subsystem: Tekram Technology Co.,Ltd. DC390F Ultra Wide SCSI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at f3800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]

00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Subsystem: Realtek Semiconductor Co., Ltd. RT8029(AS)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at b400 [size=32]

00:10.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs: Unknown device 8061
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at a800 [disabled] [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 MAX/Dual Head 32Mb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f6000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at f5000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at f4800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at f5ff0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1


Bus 002 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI-alt Root Hub
iSerial 1 d000
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))

Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI-alt Root Hub
iSerial 1 d400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))

Bus 001 Device 002: ID 04cc:1122 Philips Semiconductors
Language IDs: none (cannot get min. string descriptor; got len=-1, error=32:Broken pipe)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x04cc Philips Semiconductors
idProduct 0x1122
bcdDevice 1.10
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 1
bInterval 255
Language IDs: none (cannot get min. string descriptor; got len=-1, error=32:Broken pipe)

Bus 001 Device 003: ID 046d:c00b Logitech Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 Interface
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x046d Logitech Inc.
idProduct 0xc00b
bcdDevice 6.10
iManufacturer 1 Logitech
iProduct 2 USB Mouse
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 68
cannot get report descriptor
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 10
Language IDs: (length=4)
0409 English(US)

Bus 001 Device 004: ID 0403:8401 Future Technology Devices
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 Interface
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0403 Future Technology Devices
idProduct 0x8401
bcdDevice 1.00
iManufacturer 1 FTDI
iProduct 2 PS/2 Keyboard And Mouse I/F
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 2
bmAttributes 0xa0
Remote Wakeup
MaxPower 90mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 2 PS/2 Keyboard And Mouse I/F
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 63
cannot get report descriptor
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 105
cannot get report descriptor
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 10
Language IDs: (length=4)
0409 English(US)
Linux version 2.4.11-xfs (root@intolerance) (gcc version 2.95.4 20011006 (Debian prerelease)) #1 Wed Oct 10 19:34:44 CDT 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 131052
zone(0): 4096 pages.
zone(1): 126956 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=Linux ro root=803
Initializing CPU#0
Detected 803.413 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1602.35 BogoMIPS
Memory: 512968k/524208k available (1777k kernel code, 10852k reserved, 411k data, 216k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf08f0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
PCI: Found IRQ 9 for device 00:0e.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IA-32 Microcode Update Driver: v1.08 <tigran@veritas.com>
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
Starting kswapd
devfs: v0.117 (20010927) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
SGI XFS with ACLs, EAs, DMAPI, realtime, no debug enabled
parport_pc: Via 686A parallel port disabled in BIOS
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=16
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
hda: CR-2801TE, ATAPI CD/DVD-ROM drive
hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
hdc: Maxtor 53073U6, ATA DISK drive
hdd: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdc: 60030432 sectors (30736 MB) w/2048KiB Cache, CHS=59554/16/63
ide-floppy driver 0.97.sv
hdb: 98304kB, 196608 blocks, 512 sector size
hdb: 98304kB, 32/64/96 CHS, 4096 kBps, 512 sector size, 2941 rpm
Partition check:
/dev/ide/host0/bus0/target1/lun0: p1
/dev/ide/host0/bus1/target0/lun0: [PTBL] [14888/64/63] p1 p2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
PCI: Enabling device 00:0e.0 (0000 -> 0001)
PCI: Found IRQ 9 for device 00:0e.0
eth0: RealTek RTL-8029 found at 0xb400, IRQ 9, 00:00:21:48:78:A6.
Linux video capture interface: v1.00
ide-floppy driver 0.97.sv
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 11 for device 00:0d.0
PCI: Sharing IRQ 11 with 01:00.0
sym53c8xx: at PCI bus 0, device 13, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875 detected with Tekram NVRAM
sym53c875-0: rev 0x3 on pci bus 0 device 13 function 0 irq 11
sym53c875-0: Tekram format NVRAM, ID 7, Fast-20, Parity Checking
scsi0 : sym53c8xx-1.7.3c-20010512
Vendor: SEAGATE Model: ST15230W SUN4.2G Rev: 0738
Type: Direct-Access ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-2801TE Rev: 1.07
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TOSHIBA Model: DVD-ROM SD-M1212 Rev: 1L10
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
sym53c875-0-<0,*>: FAST-10 WIDE SCSI 20.0 MB/s (100.0 ns, offset 15)
SCSI device sda: 8386733 512-byte hdwr sectors (4294 MB)
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 10 for device 00:04.2
PCI: Sharing IRQ 10 with 00:04.3
uhci.c: USB UHCI at I/O 0xd400, IRQ 10
usb.c: new USB bus registered, assigned bus number 1
usb: raced timeout, pipe 0x80000000 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
hub.c: USB hub found
usb: raced timeout, pipe 0x80000180 status 0 time left 0
hub.c: 2 ports detected
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
PCI: Found IRQ 10 for device 00:04.3
PCI: Sharing IRQ 10 with 00:04.2
uhci.c: USB UHCI at I/O 0xd000, IRQ 10
usb.c: new USB bus registered, assigned bus number 2
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000000 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
hub.c: USB new device connect on bus1/2, assigned device number 2
hub.c: USB hub found
hub.c: 5 ports detected
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
hub.c: USB new device connect on bus1/2/1, assigned device number 3
usb.c: USB device 3 (vend/prod 0x46d/0xc00b) is not claimed by any active driver.
hub.c: USB new device connect on bus1/2/5, assigned device number 4
usb.c: USB device 4 (vend/prod 0x403/0x8401) is not claimed by any active driver.
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
hub.c: USB hub found
usb: raced timeout, pipe 0x80000180 status 0 time left 0
hub.c: 2 ports detected
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
LVM version 0.9.1_beta6 by Heinz Mauelshagen (12/03/2001)
lvm -- Driver successfully initialized
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_conntrack (4095 buckets, 32760 max)
ip_tables: (c)2000 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 216k freed
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
Adding Swap: 61840k swap-space (priority -1)
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Trying generic Via routines for device id: 0605
agpgart: AGP aperture is 64M @ 0xf8000000
[drm] AGP 0.99 on VIA @ 0xf8000000 64MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
Creative EMU10K1 PCI Audio Driver, version 0.16, 19:42:30 Oct 10 2001
PCI: Enabling device 00:10.0 (0004 -> 0005)
PCI: Assigned IRQ 5 for device 00:10.0
emu10k1: EMU10K1 rev 7 model 0x8061 found, IO at 0xb000-0xb01f, IRQ 5
ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
usb.c: registered new driver hid
input0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb1:3.0
input1: USB HID v1.00 Keyboard [FTDI PS/2 Keyboard And Mouse I/F] on usb1:4.0
input2: USB HID v1.00 Mouse [FTDI PS/2 Keyboard And Mouse I/F] on usb1:4.1
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
mice: PS/2 mouse device common for all mice
usb: raced timeout, pipe 0x80000100 status 0 time left 0
XFS mounting filesystem sd(8,1)
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000100 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
usb: raced timeout, pipe 0x80000180 status 0 time left 0
eth0: no IPv6 routers present
\
 
 \ /
  Last update: 2005-03-22 13:08    [W:0.085 / U:7.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site