Messages in this thread |  | | Date | Wed, 10 Jan 2001 10:57:50 +0100 | From | Stéphane Borel <> | Subject | Re: IBM Netfinity with 2.4.0 |
| |
On Wed, Jan 10, 2001 at 07:45:54PM +1100, Andrew Morton wrote: > "Stéphane Borel" wrote: > > *On the 7100, the final kernel can't detect two pci card (3C980 and > > ForeRunnerLE. > > Can it detect other PCI devices?
The serveraid card is detected well.
> The output from `dmesg' and `lspci -vv' would be interesting.
part of dmseg :
Setting commenced=1, go go go PCI: PCI BIOS revision 2.10 entry at 0xfd5cc, last bus=6 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: ServerWorks host bridge: secondary bus 01 PCI: ServerWorks host bridge: secondary bus 00 PCI->APIC IRQ transform: (B1,I1,P0) -> 20 PCI->APIC IRQ transform: (B0,I5,P0) -> 16 PCI->APIC IRQ transform: (B0,I15,P0) -> 26 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 DMI 2.1 present. 82 structures occupying 4232 bytes. DMI table at 0x000F944D. BIOS Vendor: IBM BIOS Version: -[MWE121AUS-1.04]- BIOS Release: 06/22/2000 System Vendor: IBM. Product Name: Netfinity 7100 -[8666]-. Version 1-jumper on pins 2-3. Serial Number 550236H. Board Vendor: IBM. Board Name: ,. Board Version: ,. Asset Tag: Changing the position of this jumper does not affect . Starting kswapd v1.8 pty: 256 Unix98 ptys configured Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ServerWorks OSB4: IDE controller on PCI bus 00 dev 79 ServerWorks OSB4: chipset revision 0 ServerWorks OSB4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x0840-0x0847, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x0848-0x084f, BIOS settings: hdc:pio, hdd:pio hda: LTN485S, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pcnet32_probe_pci: found device 0x001022.0x002000 ioaddr=0x002000 resource_flags=0x000101 eth0: PCnet/FAST III 79C975 at 0x2000, 00 06 29 55 43 74 pcnet32: pcnet32_private lp=f7bfc000 lp_dma_addr=0x37bfc000 assigned IRQ 16. pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de SCSI subsystem driver Revision: 1.00 scsi0 : IBM PCI ServeRAID 4.20.20 <ServeRAID 4M>
lspci -vv
00:00.0 Host bridge: Relience Computer CNB20HE (rev 21) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.1 Host bridge: Relience Computer CNB20HE (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 96 set, cache line size 08
00:00.2 Host bridge: Relience Computer: Unknown device 0006 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
00:00.3 Host bridge: Relience Computer: Unknown device 0006 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
00:05.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet LANCE] (rev 44) Subsystem: IBM: Unknown device 2000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 24 min, 24 max, 100 set Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 2000 [size=32] Region 1: Memory at febffc00 (32-bit, non-prefetchable) [size=32] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [40] Power Management version 2 Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+ Status: D0 PME-Enable- DSel=0 DScale=1 PME-
00:06.0 VGA compatible controller: S3 Inc. Trio 64 3D (rev 01) (prog-if 00 [VGA]) Subsystem: IBM Integrated Trio3D Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 4 min, 255 max, 96 set Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [44] Power Management version 1 Flags: PMEClk- AuxPwr- DSI+ D1+ D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0f.0 ISA bridge: Relience Computer: Unknown device 0200 (rev 4f) Subsystem: Relience Computer: Unknown device 0200 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 set 00:0f.1 IDE interface: Relience Computer: Unknown device 0211 (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 100 set Region 4: I/O ports at 0840 [size=16] 00:0f.2 USB Controller: Relience Computer: Unknown device 0220 (rev 04) (prog-if 10 [OHCI]) Subsystem: Relience Computer: Unknown device 0220 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 80 max, 96 set, cache line size 08 Interrupt: pin A routed to IRQ 26 Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K] 01:01.0 RAID bus controller: IBM: Unknown device 01bd Subsystem: IBM: Unknown device 01be Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 96 set, cache line size 08 Interrupt: pin A routed to IRQ 20 Region 0: Memory at f4ffe000 (32-bit, prefetchable) [size=8K] Expansion ROM at <unassigned> [disabled] [size=32K]
The network adapter found is an onboard chip ; we also have a 3com 3c980 and an atm adapter in the server, which give the following lines with 2.2.18 :
02:03.0 Ethernet controller: 3Com Corporation: Unknown device 9805 (rev 78) Subsystem: 3Com Corporation: Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 10 min, 10 max, 96 set, cache line size 08 Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 2080 Region 1: Memory at f6fffc00 (32-bit, non-prefetchable) Capabilities: [dc] Power Management version 2 Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+ Status: D0 PME-Enable- DSel=0 DScale=2 PME- 02:04.0 ATM network controller: Integrated Device Tech IDT77211 ATM Adapter (rev 03) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 5 min, 5 max, 96 set Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at 2100 Region 1: Memory at f6ffe000 (32-bit, non-prefetchable) .
-- Stef - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/
|  |