Messages in this thread |  | | Date | Mon, 1 Jan 2001 10:05:17 -0800 (PST) | From | Scott Conway <> | Subject | 2.4 kernel halting... |
| |
Hi, I'm having problems getting anything from 2.4.0-test12 onward to get past the IDE detectin phase of bootup, and not even 2.4.0-prerelease will work, either. At the bottom of this is the output of dmesg, on my current kernel (2.4.0-test11), with the spot where test12+ freezes indicated. btw...does anyone out there know how to capture output on a bad kernel; since the one I'm having trouble with never gets far enough for me to check for an oops with an externel program? You can locate the point where I get the freeze by the whole line of '*' to show where it locks up. Also, please forward any replies to my e-mail since I don't subscribe to linux-kernel due to excessive traffic on my end. Thanks, and below is dmesg output...
------------------------Cut Here----------------------- Linux version 2.4.0-test11-ac4 (root@ummagumma) (gcc version 2.95.3 19991030 (prerelease)) #1 Wed Dec 27 03:15:22 EST 2000 BIOS-provided physical RAM map: BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable) BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved) BIOS-e820: 0000000000020000 @ 00000000000e0000 (reserved) BIOS-e820: 0000000007f00000 @ 0000000000100000 (usable) BIOS-e820: 0000000000001000 @ 00000000fec00000 (reserved) BIOS-e820: 0000000000001000 @ 00000000fee00000 (reserved) BIOS-e820: 0000000000020000 @ 00000000fffe0000 (reserved) Scan SMP from c0000000 for 1024 bytes. Scan SMP from c009fc00 for 1024 bytes. Scan SMP from c00f0000 for 65536 bytes. Scan SMP from c009fc00 for 4096 bytes. On node 0 totalpages: 32768 zone(0): 4096 pages. zone(1): 28672 pages. zone(2): 0 pages. mapped APIC to ffffe000 (01223000) Kernel command line: BOOT_IMAGE=Linux ro root=302 adlib=0x388 ftape=1,fc10 ftape=9,irq ftape=0,dma ide0=autotune ide1=autotune idebus=66 lp=auto parport=0x378,7,3 pci=biosirq sb=0x220,5,1,7 video=matrox:disabled [000] ftape-setup.c (ftape_setup) - fc10=1. [001] ftape-setup.c (ftape_setup) - irq=9. [002] ftape-setup.c (ftape_setup) - dma=0. ide_setup: ide0=autotune ide_setup: ide1=autotune ide_setup: idebus=66 Initializing CPU#0 Detected 199.966 MHz processor. Console: colour VGA+ 132x60 Calibrating delay loop... 398.95 BogoMIPS Memory: 126276k/131072k available (1634k kernel code, 4408k reserved, 116k data, 204k init, 0k highmem) Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes) Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 8192 (order: 4, 65536 bytes) CPU: Before vendor init, caps: 008001bf 00000000 00000000, vendor = 0 Intel Pentium with F0 0F bug - workaround enabled. CPU: After vendor init, caps: 008001bf 00000000 00000000 00000000 CPU: After generic, caps: 008001bf 00000000 00000000 00000000 CPU: Common caps: 008001bf 00000000 00000000 00000000 CPU: Intel Pentium MMX stepping 03 Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: PCI BIOS revision 2.10 entry at 0xfdb11, last bus=0 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Using BIOS Interrupt Routing Table PCI: Using BIOS for IRQ routing Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 DMI 2.0 present. 0 structures occupying 0 bytes. DMI table at 0x000F0000. Starting kswapd v1.8 0x378: FIFO is 16 bytes 0x378: writeIntrThreshold is 1 0x378: readIntrThreshold is 1 0x378: PWord is 8 bits 0x378: Interrupts are ISA-Pulses 0x378: ECP port cfgA=0x10 cfgB=0x4b 0x378: ECP settings irq=7 dma=3 parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) pty: 256 Unix98 ptys configured lp0: using parport0 (interrupt-driven). ftape v3.04d 25/11/97 for Linux 2.4.0-test11-ac4 [003] ftape-init.c (ftape_init) - installing QIC-117 floppy tape hardware drive ... . [004] ftape-init.c (ftape_init) - ftape_init @ 0xc02c3910. [005] ftape-buffer.c (add_one_buffer) - buffer nr #1 @ c12e04e0, dma area @ c0328000. [006] ftape-buffer.c (add_one_buffer) - buffer nr #2 @ c12e0560, dma area @ c0090000. [007] ftape-buffer.c (add_one_buffer) - buffer nr #3 @ c12e05e0, dma area @ c0008000. [008] ftape-calibr.c (time_inb) - inb() duration: 394 nsec. [009] ftape-calibr.c (ftape_calibrate) - TC for `ftape_udelay()' = 570 nsec (at 10239 counts). [010] ftape-calibr.c (ftape_calibrate) - TC for `fdc_wait()' = 1926 nsec (at 5119 counts). zftape for ftape v3.04d 25/11/97 for Linux 2.4.0-test11-ac4 [011] zftape-init.c (zft_init) - zft_init @ 0xc02c3cd0. [012] zftape-init.c (zft_init) - installing zftape VFS interface for ftape driver .... Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 66MHz system bus speed for PIO modes ALI15X3: IDE controller on PCI bus 00 dev 58 PCI: Assigned IRQ 14 for device 00:0b.0 ALI15X3: chipset revision 32 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio hda: Maxtor 32049H2, ATA DISK drive hdb: WDC AC21600H, ATA DISK drive hdc: Maxtor 71626 A, ATA DISK drive hdd: BCD-40XH CD-ROM, ATAPI CDROM drive
******************************************************* This is the last line of bootup I see before the kernel freezes. *******************************************************
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 40021632 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63, (U)DMA hdb: 3173184 sectors (1625 MB) w/128KiB Cache, CHS=787/64/63, DMA hdc: 3184170 sectors (1630 MB) w/64KiB Cache, CHS=3158/16/63, DMA hdd: ATAPI 24X CD-ROM drive, 256kB Cache Uniform CD-ROM driver Revision: 3.11 Partition check: hda: hda1 hda2 hdb: hdb1 hdc: [PTBL] [789/64/63] hdc1 hdc2 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A ttyS02 at 0x03e8 (irq = 4) is a 16550A input0: Analog 3-axis 4-button joystick at gameport0.0 [TSC timer, 200 MHz clock, 1674 ns res] gameport0: NS558 ISA at 0x200 size 8 speed 602 kHz PPP generic driver version 2.4.1 PPP Deflate Compression module registered PPP BSD Compression module registered YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996 Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996 <Sound Blaster 16 (4.12)> at 0x220 irq 5 dma 1,7 usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xc8806000, IRQ 11 usb-ohci.c: usb-00:0f.0, Acer Laboratories Inc. [ALi] M5237 USB usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver hid usb.c: registered new driver usbscanner scanner.c: USB Scanner support registered. usb.c: registered new driver usblp event0: Event device for input0 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 8192 bind 8192) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kmem_create: Forcing size word alignment - nfs_fh VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 204k freed hub.c: USB new device connect on bus1/2, assigned device number 2 usb.c: USB device 2 (vend/prod 0x3f0/0x405) is not claimed by any active driver. Adding Swap: 54424k swap-space (priority -1)
__________________________________________________ Do You Yahoo!? Yahoo! Photos - Share your holiday photos online! http://photos.yahoo.com/ - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/
|  |