lkml.org 
[lkml]   [2000]   [Sep]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
Subjectfailed to exec /sbin/modprob -s -k binfmt-0000,errno=2
After i compiled kernel,i get these messages at boot time
I got the kernel linux-2.4.0-test7.tar.gz,after i complied the kernel,i
modified my /etc/lilo.conf, that is
_____________________________________________
boot=/dev/sda
map=/boot/map
install=/boot/boot.b
prompt
timeout=50
default=linux
image=/boot/vmlinuz-2.4.0-test7
label=linux-2.4.0
initrd=/boot/initrd-2.4.0.img
read-only
root=/dev/sda6

image=/boot/vmlinuz-2.3.99-pre9
label=linux-2.3.99
initrd=/boot/initrd-2.3.99-pre9.img
read-only
root=/dev/sda6
image=/boot/vmlinuz-2.2.14-2.0smp
label=linux
initrd=/boot/initrd-2.2.14-2.0smp.img
read-only
root=/dev/sda6
_________________________________________________
when lilo appeared,i choose linux-2.4.0 and i got the following
messages:
kmod:failed to exec /sbin/modprobe -s -k binfmt-0000,errno=2
(the message appeared 4 times)
kmod:failed to exec /sbin/modprobe -s -k block-major-8,errno=2
VFS:cannot open root device "806" or 08:06
kernel panic:VFS:unable to mount root fs on 08:06

(1) my processor informations
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 7
model name : Pentium III (Katmai)
stepping : 3
cpu MHz : 499.151528
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
sep_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov
pat pse36 mmx fxsr xmm
bogomips : 498.07

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 7
model name : Pentium III (Katmai)
stepping : 2
cpu MHz : 499.151528
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
sep_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov
pat pse36 mmx fxsr xmm
bogomips : 498.07

(2) my modules information
nfsd 144604 8 (autoclean)
nfs 28600 1 (autoclean)
lockd 31144 1 (autoclean) [nfsd nfs]
sunrpc 54116 1 (autoclean) [nfsd nfs lockd]
eepro100 12304 1 (autoclean)
raid5 18280 1 (autoclean)
aic7xxx 112848 11

(3) loaded driver
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
02f8-02ff : serial(auto)
0376-0376 : ide1
03c0-03df : vga+
03f8-03ff : serial(auto)
70e0-70ff : Intel Speedo3 Ethernet
7400-74be : aic7xxx
7800-78be : aic7xxx
fff8-ffff : ide1
(4) PCI information
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(rev 03
)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Step
ping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at e4000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=21
Command: RQ=31 SBA+ AGP- 64bit- FW- Rate=21

00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge
(rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 64 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f7f00000-f7ffffff
Prefetchable memory behind bridge: e8000000-f7cfffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

00:02.0 Ethernet controller: Intel Corporation 82557 (rev 05)
Subsystem: Unknown device 1014:00d7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 8 min, 56 max, 64 set, cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e3fff000 (32-bit, prefetchable)
Region 1: I/O ports at 70e0 Region 2: Memory at f7e00000
(32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr+ DSI+ D1+ D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

00:04.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Step
ping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 0 set
00:04.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at fff0

00:04.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 48 set
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at ff00

00:04.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-

00:0d.0 SCSI storage controller: Adaptec 2940U2
Subsystem: Unknown device 9005:a180
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 39 min, 25 max, 208 set, cache line size 08
Interrupt: pin A routed to IRQ 17
BIST result: 00
Region 0: I/O ports at 7400 Region 1: Memory at f7dfe000
(64-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0e.0 SCSI storage controller: Adaptec 2940U2
Subsystem: Unknown device 9005:a180
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 39 min, 25 max, 208 set, cache line size 08
Interrupt: pin A routed to IRQ 18
BIST result: 00
Region 0: I/O ports at 7800
Region 1: Memory at f7dff000 (64-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: S3 Inc.: Unknown device 8a22 (rev 02)

Subsystem: Unknown device 105d:0018
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
Latency: 4 min, 255 max, 248 set, cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7f80000 (32-bit, non-prefetchable)
Region 1: Memory at e8000000 (32-bit, prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=21
Command: RQ=31 SBA- AGP- 64bit- FW- Rate=21

(5)SCSI information
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DNES-318350W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 15 Lun: 00
Vendor: IBM Model: EXP200 Rev: 1020
Type: Processor ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 02 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 03 Lun: 00
Vendor: IBM Model: DNES-318350Y Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 15 Lun: 00
Vendor: IBM Model: EXP200 Rev: 1020
Type: Processor ANSI SCSI revision: 02

regards,
saya


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:38    [W:0.028 / U:12.892 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site