lkml.org 
[lkml]   [2000]   [Feb]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subjectkernel 2.2.15pre6 gfp fault. pre5 didn't do this.

Hi all,
This the dmesg command. These gfp faults occur when I run the
following command:

lynx http://www.slashdot.org


Apparently, it must be something in the networking code I presume although
I get my "slashdot" data and can surf the Web. Each time it goes out
to a network address I get these gfp's.



Linux version 2.2.15pre6 (root@DosLinux) (gcc version egcs-2.90.29 980515 (egcs-1.0.3 release)) #1 SMP Tue Feb 8 09:11:43 /etc/localtime 2000
mapped APIC to ffffe000 (00268000)
Detected 331709268 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 330.96 BogoMIPS
Memory: 127928k/131072k available (1128k kernel code, 416k reserved, 1544k data, 56k init)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
VFS: Diskquotas version dquot_6.4.0 initialized
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
per-CPU timeslice cutoff: 100.21 usecs.
CPU0: Intel Pentium II (Deschutes) stepping 01
SMP motherboard not detected. Using dummy APIC emulation.
PCI: PCI BIOS revision 2.10 entry at 0xfcaee
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
parport0: PC-style at 0x378 (0x778) [SPP,ECP,ECPPS2]
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hdc: QUANTUM FIREBALL_TM1280A, ATA DISK drive
hdd: TOSHIBA CD-ROM XM-6202B, ATAPI CDROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: QUANTUM FIREBALL_TM1280A, 1222MB w/76kB Cache, CHS=2484/16/63, DMA
hdd: ATAPI 32X CD-ROM drive, 256kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
(scsi0) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 14/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Warning - detected auto-termination
(scsi0) Please verify driver detected settings are correct.
(scsi0) If not, then please properly set the device termination
(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi0) during machine bootup.
(scsi0) Cables present (Int-50 NO, Int-68 YES, Ext-68 NO)
(scsi0) Downloading sequencer code... 374 instructions downloaded
(scsi1) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 14/1
(scsi1) Narrow Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Warning - detected auto-termination
(scsi1) Please verify driver detected settings are correct.
(scsi1) If not, then please properly set the device termination
(scsi1) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi1) during machine bootup.
(scsi1) Cables present (Int-50 NO, Ext-50 NO)
(scsi1) Downloading sequencer code... 374 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.23/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.23/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 3 hosts.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
(scsi0:0:0:0) Data overrun detected in Data-In phase, tag 1;
Have seen Data Phase. Length=255, NumSGs=1.
sg[0] - Addr 0x7fec380 : Length 255
Vendor: WDIGTL Model: WDE9100-1807A4 Rev: 1.30
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17783204 [8683 MB] [8.7 GB]
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 >
hdc: [PTBL] [621/64/63] hdc1
UMSDOS 0.85g (compatibility level 0.4, fast msdos)
check_pseudo_root: mounted as root
check_pseudo_root: found //linux
check_pseudo_root: found sbin/init, enabling pseudo-root
UMSDOS: changed to alternate root
VFS: Mounted root (umsdos filesystem).
Freeing unused kernel memory: 56k freed
CSLIP: code copyright 1989 Regents of the University of California
SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256).
SLIP linefill/keepalive option.
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
PPP BSD Compression module registered
PPP Deflate Compression module registered
ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xdc00, 00:c0:4f:78:7a:80, IRQ 11
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
MII transceiver found at address 0, status 786d.
Enabling bus-master transmits and whole-frame receives.
ppa: Version 2.03 (for Linux 2.2.x)
ppa: Found device at ID 6, Attempting to use EPP 16 bit
ppa: Found device at ID 6, Attempting to use PS/2
ppa: Communication established with ID 6 using PS/2
scsi3 : Iomega VPI0 (ppa) interface
scsi : 4 hosts.
Vendor: IOMEGA Model: ZIP 100 Rev: D.17
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sdb at scsi3, channel 0, id 6, lun 0
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sdb: Write Protect is off
sdb: sdb4
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
gfp called by non-running (1) task from c011d181!
gfp called by non-running (1) task from c011d642!
gfp called by non-running (1) task from c011d181!
gfp called by non-running (1) task from c011d181!
gfp called by non-running (1) task from c011d181!
gfp called by non-running (1) task from c011d181!
gfp called by non-running (1) task from c011d181!
gfp called by non-running (1) task from c011d642!



MIke



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:56    [W:0.207 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site