lkml.org 
[lkml]   [2000]   [Dec]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject2.4.0-test12 hangs during partition mapping
Date
Hi all!

I tried to compile kernel 2.4.0-test12 but experienced no success in booting it:
in fact it just hangs when trying to recognize the partitions of my hde.
Here are the messages that are printed when I boot the standard Mandrake 7.1 kernel, that works
fine and recognizes well my Promise Ultra66 controller and the PTBL nature of my hde:

Linux version 2.2.15-4mdk (chmou@kenobi.mandrakesoft.com)
(gcc version 2.95.3 19991030 (prerelease)) #1 Wed May 10 15:31:30 CEST 2000
Detected 233867424 Hz processor.
ide_setup: hdc=ide-scsi
ide_setup: ide2=0xb000,0xa800

ide_setup: ide3=0xa400,0xa000

[...]

PCI: PCI BIOS revision 2.10 entry at 0xf06d0
PCI: Using configuration type 1
PCI: Probing PCI hardware

[...]

Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:pio
PDC20262: IDE controller on PCI bus 00 dev 50
PDC20262: not 100% native mode: will probe irqs later
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0x9800-0x9807, BIOS settings: hde:DMA, hdf:DMA
ide3: BM-DMA at 0x9808-0x980f, BIOS settings: hdg:DMA, hdh:pio
hda: WDC AC22100H, ATA DISK drive
hdc: Hewlett-Packard CD-Writer Plus 8100, ATAPI CDROM drive
hde: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hde: FUJITSU MPB3064ATU, ATA DISK drive
hdf: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
hdf: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
hdg: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hdg: QUANTUM FIREBALLP LM15, ATA DISK drive
hdh: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
hdh: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xb000-0xb007,0xa800 on irq 9
ide3 at 0xa400-0xa407,0xa000 on irq 9
hda: WDC AC22100H, 2014MB w/128kB Cache, CHS=1023/64/63
hde: FUJITSU MPB3064ATU, 6187MB w/0kB Cache, CHS=13410/15/63
hdg: QUANTUM FIREBALLP LM15, 14324MB w/1900kB Cache, CHS=29104/16/63
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 515.112 MB/sec
p5_mmx : 538.734 MB/sec
8regs : 417.957 MB/sec
32regs : 220.218 MB/sec
using fastest function: p5_mmx (538.734 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2 hda3
hde: [PTBL] [788/255/63] hde1
hdg: [PTBL] [1027/255/63] hdg1 hdg2 hdg3 < hdg5 hdg6 hdg7 > hdg4
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 72k freed

etc ...

When I select the 2.4.0-test12 kernel I just compiled (I feed it with the same
parameters about ide2 and ide3) it boots, recognizes the Promise controller
but hangs just after:

Partition check:
hda: hda1 hda2 hda3
hde:

Is there any parameter I can give to the kernel or any patch I can use to boot
the new kernel?

Thank you in advance!

PS. Since I'm not subscribed to this mailing list, I would like to be personally
CC'ed the answers/comments posted to the list in response to my posting. Thank
you!

--
Francesco Anselmo
pisuke@libero.it
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:52    [W:0.031 / U:0.240 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site