lkml.org 
[lkml]   [2000]   [Nov]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: 440FX and DMA on 2.2.18pre18

It looks like you have a P6DNE and yes it doesn, but the patches are
required to downgrade the drive to the host limits.

Cheers,


On Sun, 5 Nov 2000, Ville Herva wrote:

> I have a dual Ppro200 with 440FX chipset and an IBM 30GB ide disk. The
> kernel is 2.2.18pre18 with no additional patches. DMA appears not to work
> with this combination.
>
> lspci:
>
> 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02)
> 00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
> 00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]
> 00:07.2 USB Controller: Intel Corporation 82371SB PIIX3 USB [Natoma/Triton II] (rev 01)
> 00:0c.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 02)
> 00:0d.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2164W [Millennium II]
> 00:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7871
>
> hdparm -i /dev/hda:
>
> /dev/hda:
>
> Model=IBM-DTLA-305030, FwRev=TW3OA60A, SerialNo=YG0YG017000
> Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
> BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=off
> CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60036480
> IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
>
> hdparm /dev/hda:
>
> /dev/hda:
> multcount = 0 (off)
> I/O support = 0 (default 16-bit)
> unmaskirq = 0 (off)
> using_dma = 0 (off)
> keepsettings = 0 (off)
> nowerr = 0 (off)
> readonly = 0 (off)
> readahead = 8 (on)
> geometry = 3737/255/63, sectors = 60036480, start = 0
>
> If I do hdparm -d1; hdparm -tT /dev/hda
>
> hda: timeout waiting for DMA
> hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
> VFS: Disk change detected on device ide0(3,64)
> hda: timeout waiting for DMA
> hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
> hda: timeout waiting for DMA
> hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
> hda: timeout waiting for DMA
> hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
> hda: DMA disabled
> ide0: reset: success
>
> On another box with a single PPro200 and 440FX chipset, DMA works just
> fine. That box also has IBM disk (30GB) but runs 2.0.37.
>
> Should I try the IDE-patch or suspect the cable? Can anybody confirm that
> DMA works with 440FX and a recent 2.2.x?
>
>
> -- v --
>
> v@iki.fi
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> Please read the FAQ at http://www.tux.org/lkml/
>

Andre Hedrick
CTO Timpanogas Research Group
EVP Linux Development, TRG
Linux ATA Development

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:45    [W:0.047 / U:22.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site