lkml.org 
[lkml]   [2000]   [Jan]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subjecthda: dma_intr: status=0x51 { DriveReady SeekComplete Error } 2.2.15pre4
Date
I have been getting the following errors since I upgraded to 2.2.15pre4. 
I do not think that I configured anything different this time around. I can not
figure out what if there is something in particular that causes this error.

hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: DMA disabled
hdb: DMA disabled
ide0: reset: success:

I am running:
Linux calvert 2.2.15pre4 #2 Mon Jan 24 18:02:46 EST 2000 i686 unknown
Kernel modules 2.1.121
Gnu C 2.95.2
Binutils 2.9.5.0.16
Linux C Library 2.1.2
Dynamic linker ldd (GNU libc) 2.1.2
Procps 2.0.6
Mount 2.9y
Net-tools 1.53
Console-tools 0.2.2
Sh-utils 2.0
Modules Loaded vfat fat
With hda and hdb being:
[root@calvert linux]# hdparm -vi /dev/hda

/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1401/255/63, sectors = 22510656, start = 0

Model=Maxtor 91152D8, FwRev=WAS82739, SerialNo=K806FPDA
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=3(DualPortCache), BuffSize=256kB, MaxMultSect=16, MultSect=off
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)

tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

[root@calvert linux]# hdparm -vi /dev/hdb

/dev/hdb:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 3739/255/63, sectors = 60074784, start = 0

Model=WDC WD307AA, FwRev=05.05B05, SerialNo=WD-WMA111025946
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=60074784
WARNING 43560720 ORPHANED SECTORS :: KERNEL REPORTING ERROR
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4
Drive Supports : ATA-1 ATA-2 ATA-3 ATA-4

lspci reports my ide controller being a:
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Flags: bus master, medium devsel, latency 64
I/O ports at 1000


--
--
Douglas F. Elznic
<dfelznic @ syr.edu>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:56    [W:0.089 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site