I have the Promise Ultra66 (PDC20262) supported now, plus generic
ATA-66 support.

You will need "hdparm-3.5i.patch" against "hdparm-3.5.tar.gz" to get new
support.

Apr 24 09:47:27 Orion kernel:
Uniform Multi-Platform E-IDE driver Revision: 6.19
PDC20262: IDE controller on PCI bus 00 dev a0
PDC20262: not 100ative mode: will probe irqs later
PDC20262: ROM enabled at 0xfebb0000
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
    ide0: BM-DMA at 0xef00-0xef07, BIOS settings: hda:pio, hdb:DMA
    ide1: BM-DMA at 0xef08-0xef0f, BIOS settings: hdc:pio, hdd:pio
HPT343: IDE controller on PCI bus 00 dev 98
HPT343: not 100ative mode: will probe irqs later
    ide2: BM-DMA at 0xee80-0xee87, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xee88-0xee8f, BIOS settings: hdg:pio, hdh:pio
PIIX3: IDE controller on PCI bus 00 dev 39
PIIX3: device not capable of full native PCI mode
PIIX3: device disabled (BIOS)
hda: QUANTUM FIREBALL ST6.4A, ATA DISK drive
hdb: QUANTUM FIREBALL ST3.2A, ATA DISK drive
hdc: Maxtor 72004 AP, ATA DISK drive
hdd: Maxtor 71626 A, ATA DISK drive
hde: CD-ROM CDU611, ATAPI CDROM drive
hdf: NEC CD-ROM DRIVE:251, ATAPI CDROM drive
hdg: HP COLORADO 8GB, ATAPI TAPE drive
hdh: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0xeff0-0xeff7,0xefe6 on irq 19
ide1 at 0xefa8-0xefaf,0xefe2 on irq 19
ide2 at 0xeea0-0xeea7,0xeeb6 on irq 18
ide3 at 0xeea8-0xeeaf,0xeebe on irq 18
hda: QUANTUM FIREBALL ST6.4A, 6149MB w/81kB Cache, CHS=13328/15/63, UDMA(33)
hdb: QUANTUM FIREBALL ST3.2A, 3079MB w/81kB Cache, CHS=6256/16/63, UDMA(33)
hdc: Maxtor 72004 AP, 1916MB w/128kB Cache, CHS=3893/16/63, DMA
hdd: Maxtor 71626 A, 1554MB w/64kB Cache, CHS=3158/16/63, DMA
hde: DMA disabled
hde: ATAPI 10X CD-ROM drive, 256kB Cache
Uniform CDROM driver Revision: 2.54
hdf: ATAPI 4X CD-ROM changer w/4 slots, 128kB Cache
     CD Slot 1 Empty slot.
     CD Slot 2 Empty slot.
     CD Slot 3 Empty slot.
     CD Slot 4 Empty slot.
hdg: DMA disabled
ide-tape: hdg: overriding capabilities->speed (assuming 650KB/sec)
ide-tape: hdg: overriding capabilities->max_speed (assuming 650KB/sec)
ide-tape: hdg <-> ht0, 650KBps, 16*32kB buffer, 3200kB pipeline, 250ms tDSC
hdh: 98304kB, 196608 blocks, 512 sector size
hdh: 98304kB, 32/64/96 CHS, 4096 kBps, 512 sector size, 2941 rpm


hda: set_geometry_intr: status=0x51 { DriveReady SeekComplete Error }
hda: set_geometry_intr: error=0x04 { DriveStatusError }
hdb: set_geometry_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: set_geometry_intr: error=0x04 { DriveStatusError }

These errors are cosmetic and are harmless.

Andre Hedrick
The Linux IDE guy
http://www.dyer.vanderbilt.edu/server/udma/2.2.6.uniform-ide-6.19.patch.4.gz
http://www.dyer.vanderbilt.edu/server/udma/hdparm-3.5i.patch.gz

APC UPS Daemon Support Center.
                        http://www.brisse.dk/site/apcupsd/
GPLed source on April 7, 1999



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/