Messages in this thread | | | From | "George R. Kasica" <> | Subject | SCSI Broken after 2.2.10 for Adaptec 7xxx ??? | Date | Sun, 05 Dec 1999 10:42:14 -0600 |
| |
Hello:
I think something got broken after 2.2.10 in the SCSI code for the Adaptec 7XXX adapters....Below is my boot up info for 2.2.10 (last one that appears to work) and then 2.2.11, 2.2.12 and 2.2.13 all fail similarly. They were complied with the same options using
make mrproper make config (for 2.2.10 and) make oldconfig (for 11,12 and 13.) make clean make dep make bzImage make modules make modules_install cp /vmlinuz /vmlinuz.old cp /usr/src/linux/arch/i386/boot/bzImage /vmlinuz lilo
then sync and reboot.
Under 2.2.10 the following is the SCSI init and load on botup: -------------------------------------------------------------- Dec 5 09:50:55 eagle kernel: (scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 9/0 Dec 5 09:50:55 eagle kernel: (scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs Dec 5 09:50:55 eagle kernel: (scsi0) Warning - detected auto-termination Dec 5 09:50:55 eagle kernel: (scsi0) Please verify driver detected settings are correct. Dec 5 09:50:55 eagle kernel: (scsi0) If not, then please properly set the device termination Dec 5 09:50:55 eagle kernel: (scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted Dec 5 09:50:55 eagle kernel: (scsi0) during machine bootup. Dec 5 09:50:55 eagle kernel: (scsi0) Cables present (Int-50 YES, Ext-50 YES) Dec 5 09:50:55 eagle kernel: (scsi0) Downloading sequencer code... 406 instructions downloaded Dec 5 09:50:55 eagle kernel: scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.17/3.2.4 Dec 5 09:50:55 eagle kernel: <Adaptec AIC-7850 SCSI host adapter> Dec 5 09:50:55 eagle kernel: scsi : 1 host. Dec 5 09:50:55 eagle kernel: (scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15. Dec 5 09:50:55 eagle kernel: Vendor: SEAGATE Model: ST32550N Rev:0021 Dec 5 09:50:55 eagle kernel: Type: Direct-Access ANSISCSI revision: 02 Dec 5 09:50:55 eagle kernel: Detected scsi disk sda at scsi0, channel 0, id 1,lun 0 Dec 5 09:50:55 eagle kernel: (scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 8. Dec 5 09:50:55 eagle kernel: Vendor: HP Model: C1553A Rev:NS01 Dec 5 09:50:55 eagle kernel: Type: Sequential-Access ANSISCSI revision: 02 Dec 5 09:50:55 eagle kernel: Detected scsi tape st0 at scsi0, channel 0, id 3,lun 0 Dec 5 09:50:55 eagle kernel: Vendor: HP Model: C1553A Rev:NS01 Dec 5 09:50:55 eagle kernel: Type: Medium Changer ANSISCSI revision: 02 Dec 5 09:50:55 eagle kernel: Detected scsi generic sgc at scsi0, channel 0, id3, lun 1 Dec 5 09:50:55 eagle kernel: scsi : detected 1 SCSI tape 1 SCSI disk total. Dec 5 09:50:55 eagle kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=4194058 [2047 MB] [2.0 GB]
Under 2.2.11,2.2.12 or 2.2.13 I get the following error: -------------------------------------------------------- scsi: Aborting Command due to timeout pid 11,scsi0,channel 0,id3,lun 0 Testing Unit Ready 00 00 00 00 00
and it just keeps repeating and the system will not boot.
What do i need to do to fix this....please keep it simple since I'm not a kernel hacker or C programmer by trade.
Thanks Again,
George
===[George R. Kasica]=== +1 262 513 8503 President +1 800 520 4873 FAX Netwrx Consulting Inc. Waukesha, WI USA http://www.netwrx1.com georgek@netwrx1.com ICQ #12862186
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |