lkml.org 
[lkml]   [1999]   [Oct]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectRe: Buggy HLT instruction in Cyrix M2 or error in ATAPI CDROM code ?
    Date
    > 
    > I probably can borrow different CDROM drive if that helps.
    > I will report the result later.
    >

    I tried SAMSUNG SC-148B (48x) yesterday and it DOES work.

    My old GCD-R540C does only pio 3, while the samsung does pio 4 and dma mword2
    (see below), maybe this could be the problem ?

    Can I tune something in drivers/block/ide-* to make it work ?

    Well except that pio 3 thing the GCD-R540C is an excellent drive, it reads DA
    frames, has FFWD/REV, PLAY buttons, honours SETSPEED ioctl and is absolutely
    quiet. Tha Samsung sounds like helicopter and can't be even slowed down via
    ioctl :-( It does't do 48x either (maybe internally), hdparm -t says 3MB/s.
    Anybody knows a good drive ?

    thanks,
    Frantisek Dufka


    hdparm output for both drives :


    /dev/hda:

    Model=SAMSUNG SC-148B, FwRev=BS10, SerialNo=
    Config={ SpinMotCtl Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
    RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
    BuffType=0(?), BuffSize=0kB, MaxMultSect=0
    DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
    (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
    tDMA={min:120,rec:120}, DMA modes: sword0 sword1 sword2 mword0 mword1 *mword2
    IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4


    /dev/hdb:

    Model=GCD-R540C, FwRev=1.01, SerialNo=
    Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
    RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
    BuffType=0(?), BuffSize=256kB, MaxMultSect=0
    DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
    (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
    tDMA={min:0,rec:0}, DMA modes: sword0 sword1 sword2 mword0
    IORDY=on/off, tPIO={min:180,w/IORDY:180}, PIO modes: mode3


    output of the setspeed ioctl on Samsung:

    Oct 19 11:15:29 arthur kernel: ATAPI device hda:
    Oct 19 11:15:29 arthur kernel: Error: Illegal request -- (Sense key=0x05)
    Oct 19 11:15:29 arthur kernel: Invalid command operation code -- (asc=0x20, ascq=0x00)
    Oct 19 11:15:29 arthur kernel: The failed "Set CD Speed" packet command was:
    Oct 19 11:15:29 arthur kernel: "bb 00 ff ff 00 00 00 00 00 00 00 00 "


    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.rutgers.edu
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:54    [W:0.026 / U:0.080 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site