Messages in this thread | | | Date | Fri, 15 Jan 1999 00:55:18 +0100 | From | Renaud Guerin <> | Subject | 2.2.0pre7-ac2 : OOPS during bootup with ide-scsi option |
| |
I get an oops on startup with pre7-ac2 if I append "hdd = ide-scsi" to the command line (append = "hdd=ide-scsi" in lilo.conf)
Since it occurs right after the ide probing and locks the machine, I can't save it and ksymoops it.
Pre6-ac1 and pre7 both work fine with this enabled. They display "ide_setup: hdd=ide-scsi" during bootup.
Here are the boot messages from pre7-ac2 (run without the offending option, of course)
Compiled with pgcc 1.1 with -march=pentiumpro
Linux version 2.2.0-pre7-ac2 (root@saturne.hexanet.fr) (gcc version pgcc-2.91.57 19980901 (egcs-1.1 release)) #8 ven jan 15 00:23:59 CET 1999 Detected 451028373 Hz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 450.56 BogoMIPS Memory: 128188k/131072k available (668k kernel code, 412k reserved, 1760k data, 44k init) CPU: Intel Celeron (Mendocino) stepping 00 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.26 (19981001) Richard Gooch (rgooch@atnf.csiro.au) PCI: PCI BIOS revision 2.10 entry at 0xfb300 PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP Starting kswapd v 1.5 Serial driver version 4.27 with no serial options enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured apm: BIOS version 1.2 Flags 0x07 (Driver version 1.9) PIIX4: IDE controller on PCI bus 00 dev 39 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio hda: FUJITSU MPC3043AT, ATA DISK drive hdb: QUANTUM FIREBALL_TM3840A, ATA DISK drive hdc: CD-524E, ATAPI CDROM drive hdd: HP CD-Writer+ 7200, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: FUJITSU MPC3043AT, 4125MB w/0kB Cache, CHS=525/255/63, UDMA hdb: QUANTUM FIREBALL_TM3840A, 3681MB w/76kB Cache, CHS=935/128/63, DMA Partition check: hda: hda1 hda2 hda3 hda4 hdb: hdb1 hdb2 < hdb5 > hdb3 hdb4 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 44k freed Adding Swap: 112448k swap-space (priority -1) ne2k-pci.c:v0.99L 2/7/98 D. Becker/P. Gortmaker http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xe400, IRQ 12. eth0: PCI NE2000 found at 0xe400, IRQ 12, 00:20:18:2C:30:31.
"modprobe ide-scsi" then results in:
scsi0 : SCSI host adapter emulation for IDE ATAPI devices scsi : 1 host. Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: TEAC Model: CD-524E Rev: 3.0B Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01 Type: CD-ROM ANSI SCSI revision: 02
My .config:
# # Automatically generated make config: don't edit #
# # Code maturity level options # CONFIG_EXPERIMENTAL=y
# # Processor type and features # # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set CONFIG_M686=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_TSC=y CONFIG_X86_GOOD_APIC=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y # CONFIG_SMP is not set
# # Loadable module support # CONFIG_MODULES=y # CONFIG_MODVERSIONS is not set CONFIG_KMOD=y
# # General setup # CONFIG_NET=y CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_QUIRKS=y # CONFIG_PCI_OPTIMIZE is not set CONFIG_PCI_OLD_PROC=y # CONFIG_MCA is not set CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m # CONFIG_BINFMT_JAVA is not set CONFIG_PARPORT=m CONFIG_PARPORT_PC=m # CONFIG_PARPORT_OTHER is not set CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set CONFIG_APM_CPU_IDLE=y # CONFIG_APM_DISPLAY_BLANK is not set CONFIG_APM_POWER_OFF=y # CONFIG_APM_IGNORE_MULTIPLE_SUSPEND is not set # CONFIG_APM_IGNORE_SUSPEND_BOUNCE is not set # CONFIG_APM_RTC_IS_GMT is not set # CONFIG_APM_ALLOW_INTS is not set
# # Plug and Play support # CONFIG_PNP=y CONFIG_PNP_PARPORT=m
# # Block devices # CONFIG_BLK_DEV_FD=m CONFIG_BLK_DEV_IDE=y
# # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_BLK_DEV_IDECD=m # CONFIG_BLK_DEV_IDETAPE is not set # CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=m # CONFIG_BLK_DEV_CMD640 is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_BLK_DEV_IDEDMA=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_TRM290 is not set # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_VIA82C586 is not set # CONFIG_BLK_DEV_CMD646 is not set # CONFIG_IDE_CHIPSETS is not set
# # Additional Block Devices # CONFIG_BLK_DEV_LOOP=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_MD is not set # CONFIG_BLK_DEV_RAM is not set # CONFIG_BLK_DEV_XD is not set CONFIG_PARIDE_PARPORT=m # CONFIG_PARIDE is not set # CONFIG_BLK_DEV_HD is not set
# # Networking options # CONFIG_PACKET=y # CONFIG_NETLINK is not set CONFIG_FIREWALL=y # CONFIG_NET_ALIAS is not set # CONFIG_FILTER is not set CONFIG_UNIX=y CONFIG_INET=y # CONFIG_IP_MULTICAST is not set # CONFIG_IP_ADVANCED_ROUTER is not set # CONFIG_IP_PNP is not set CONFIG_IP_FIREWALL=y CONFIG_IP_ALWAYS_DEFRAG=y # CONFIG_IP_TRANSPARENT_PROXY is not set CONFIG_IP_MASQUERADE=y
# # Protocol-specific masquerading support will be built as modules. # CONFIG_IP_MASQUERADE_ICMP=y
# # Protocol-specific masquerading support will be built as modules. # # CONFIG_IP_MASQUERADE_MOD is not set # CONFIG_IP_ROUTER is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_ALIAS is not set CONFIG_SYN_COOKIES=y
# # (it is safe to leave these untouched) # # CONFIG_INET_RARP is not set CONFIG_IP_NOSR=y CONFIG_SKB_LARGE=y # CONFIG_IPV6 is not set
# # # # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_BRIDGE is not set # CONFIG_LLC is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_NET_FASTROUTE is not set # CONFIG_NET_HW_FLOWCONTROL is not set # CONFIG_CPU_IS_SLOW is not set
# # QoS and/or fair queueing # # CONFIG_NET_SCHED is not set
# # SCSI support # CONFIG_SCSI=m
# # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=m # CONFIG_CHR_DEV_ST is not set CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=m
# # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y # CONFIG_SCSI_LOGGING is not set
# # SCSI low-level drivers # # CONFIG_SCSI_7000FASST is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_AHA152X is not set # CONFIG_SCSI_AHA1542 is not set # CONFIG_SCSI_AHA1740 is not set # CONFIG_SCSI_AIC7XXX is not set CONFIG_SCSI_ADVANSYS=m # CONFIG_SCSI_IN2000 is not set # CONFIG_SCSI_AM53C974 is not set # CONFIG_SCSI_MEGARAID is not set # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_DTC3280 is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_EATA_DMA is not set # CONFIG_SCSI_EATA_PIO is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GDTH is not set # CONFIG_SCSI_GENERIC_NCR5380 is not set # CONFIG_SCSI_G_NCR5380_PORT is not set # CONFIG_SCSI_G_NCR5380_MEM is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_IMM is not set # CONFIG_SCSI_NCR53C406A is not set # CONFIG_SCSI_SYM53C416 is not set # CONFIG_SCSI_NCR53C7xx is not set # CONFIG_SCSI_NCR53C8XX is not set # CONFIG_SCSI_PAS16 is not set # CONFIG_SCSI_PCI2000 is not set # CONFIG_SCSI_PCI2220I is not set # CONFIG_SCSI_PSI240I is not set # CONFIG_SCSI_QLOGIC_FAS is not set # CONFIG_SCSI_QLOGIC_ISP is not set # CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_SEAGATE is not set # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_T128 is not set # CONFIG_SCSI_U14_34F is not set # CONFIG_SCSI_ULTRASTOR is not set # CONFIG_SCSI_DEBUG is not set
# # Network device support # CONFIG_NETDEVICES=y
# # ARCnet devices # # CONFIG_ARCNET is not set CONFIG_DUMMY=m # CONFIG_EQUALIZER is not set
# # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_LANCE is not set # CONFIG_NET_VENDOR_SMC is not set # CONFIG_NET_VENDOR_RACAL is not set # CONFIG_RTL8139 is not set # CONFIG_YELLOWFIN is not set # CONFIG_NET_ISA is not set CONFIG_NET_EISA=y # CONFIG_PCNET32 is not set # CONFIG_ACENIC is not set # CONFIG_AC3200 is not set # CONFIG_APRICOT is not set # CONFIG_CS89x0 is not set # CONFIG_DE4X5 is not set # CONFIG_DEC_ELCP is not set # CONFIG_DGRS is not set # CONFIG_EEXPRESS_PRO100 is not set # CONFIG_LNE390 is not set # CONFIG_NE3210 is not set CONFIG_NE2K_PCI=m # CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set # CONFIG_ES3210 is not set # CONFIG_EPIC100 is not set # CONFIG_ZNET is not set # CONFIG_NET_POCKET is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set
# # Appletalk devices # CONFIG_PLIP=m CONFIG_PPP=m
# # CCP compressors for PPP are only built as modules. # # CONFIG_SLIP is not set # CONFIG_NET_RADIO is not set
# # Token ring devices # # CONFIG_TR is not set # CONFIG_RCPCI is not set CONFIG_SHAPER=m
# # Wan interfaces # # CONFIG_HOSTESS_SV11 is not set # CONFIG_COSA is not set # CONFIG_DLCI is not set
# # Amateur Radio support # # CONFIG_HAMRADIO is not set
# # IrDA subsystem support # # CONFIG_IRDA is not set
# # ISDN subsystem # # CONFIG_ISDN is not set
# # CD-ROM drivers (not for SCSI or IDE/ATAPI drives) # # CONFIG_CD_NO_IDESCSI is not set
# # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_SERIAL=y # CONFIG_SERIAL_CONSOLE is not set # CONFIG_SERIAL_EXTENDED is not set # CONFIG_SERIAL_NONSTANDARD is not set CONFIG_UNIX98_PTYS=y CONFIG_UNIX98_PTY_COUNT=256 CONFIG_PRINTER=m CONFIG_PRINTER_READBACK=y CONFIG_MOUSE=y
# # Mice # # CONFIG_ATIXL_BUSMOUSE is not set # CONFIG_BUSMOUSE is not set # CONFIG_MS_BUSMOUSE is not set CONFIG_PSMOUSE=y # CONFIG_82C710_MOUSE is not set # CONFIG_PC110_PAD is not set # CONFIG_QIC02_TAPE is not set # CONFIG_WATCHDOG is not set # CONFIG_NVRAM is not set # CONFIG_RTC is not set
# # Video For Linux # CONFIG_VIDEO_DEV=m CONFIG_RADIO_RTRACK=m # CONFIG_RADIO_RTRACK2 is not set # CONFIG_RADIO_AZTECH is not set # CONFIG_RADIO_MIROPCM20 is not set # CONFIG_RADIO_GEMTEK is not set # CONFIG_VIDEO_BT848 is not set # CONFIG_VIDEO_BWQCAM is not set # CONFIG_VIDEO_CQCAM is not set # CONFIG_VIDEO_PMS is not set # CONFIG_VIDEO_SAA5249 is not set # CONFIG_RADIO_SF16FMI is not set # CONFIG_RADIO_ZOLTRIX is not set
# # Joystick support # CONFIG_JOYSTICK=m CONFIG_JOY_ANALOG=m # CONFIG_JOY_ASSASIN is not set # CONFIG_JOY_GRAVIS is not set # CONFIG_JOY_LOGITECH is not set # CONFIG_JOY_SIDEWINDER is not set # CONFIG_JOY_THRUSTMASTER is not set # CONFIG_JOY_LIGHTNING is not set # CONFIG_JOY_CONSOLE is not set # CONFIG_JOY_DB9 is not set # CONFIG_JOY_TURBOGRAFX is not set
# # Ftape, the floppy tape device driver # # CONFIG_FTAPE is not set # CONFIG_FT_NORMAL_DEBUG is not set # CONFIG_FT_FULL_DEBUG is not set # CONFIG_FT_NO_TRACE is not set # CONFIG_FT_NO_TRACE_AT_ALL is not set # CONFIG_FT_STD_FDC is not set # CONFIG_FT_MACH2 is not set # CONFIG_FT_PROBE_FC10 is not set # CONFIG_FT_ALT_FDC is not set
# # Filesystems # # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_HFS_FS is not set CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m # CONFIG_UMSDOS_FS is not set CONFIG_VFAT_FS=m CONFIG_ISO9660_FS=m CONFIG_JOLIET=y # CONFIG_MINIX_FS is not set # CONFIG_NTFS_FS is not set # CONFIG_HPFS_FS is not set CONFIG_PROC_FS=y CONFIG_DEVPTS_FS=m # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_EXT2_FS=y # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set
# # Network File Systems # # CONFIG_CODA_FS is not set CONFIG_NFS_FS=m # CONFIG_NFSD is not set CONFIG_SUNRPC=m CONFIG_LOCKD=m CONFIG_SMB_FS=m CONFIG_SMB_WIN95=y # CONFIG_NCP_FS is not set
# # Partition Types # # CONFIG_BSD_DISKLABEL is not set # CONFIG_MAC_PARTITION is not set # CONFIG_SMD_DISKLABEL is not set # CONFIG_SOLARIS_X86_PARTITION is not set # CONFIG_UNIXWARE_DISKLABEL is not set CONFIG_NLS=y
# # Native Language Support # CONFIG_NLS_CODEPAGE_437=m # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set CONFIG_NLS_CODEPAGE_850=m # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_874 is not set CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set
# # Console drivers # CONFIG_VGA_CONSOLE=y CONFIG_VIDEO_SELECT=y # CONFIG_MDA_CONSOLE is not set CONFIG_FB=y CONFIG_DUMMY_CONSOLE=y # CONFIG_FB_VESA is not set CONFIG_VIDEO_SELECT=y CONFIG_FB_MATROX=m # CONFIG_FB_MATROX_MILLENIUM is not set # CONFIG_FB_MATROX_MYSTIQUE is not set CONFIG_FB_MATROX_G100=y # CONFIG_FB_MATROX_MULTIHEAD is not set # CONFIG_FB_PCI_ATY is not set # CONFIG_FB_VIRTUAL is not set # CONFIG_FB_ATY is not set CONFIG_FBCON_ADVANCED=y # CONFIG_FBCON_MFB is not set # CONFIG_FBCON_CFB2 is not set # CONFIG_FBCON_CFB4 is not set CONFIG_FBCON_CFB8=m CONFIG_FBCON_CFB16=m CONFIG_FBCON_CFB24=m CONFIG_FBCON_CFB32=m # CONFIG_FBCON_AFB is not set # CONFIG_FBCON_ILBM is not set # CONFIG_FBCON_IPLAN2P2 is not set # CONFIG_FBCON_IPLAN2P4 is not set # CONFIG_FBCON_IPLAN2P8 is not set # CONFIG_FBCON_MAC is not set # CONFIG_FBCON_VGA is not set # CONFIG_FBCON_FONTWIDTH8_ONLY is not set # CONFIG_FBCON_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y
# # Sound # # CONFIG_SOUND is not set
# # Kernel hacking # CONFIG_MAGIC_SYSRQ=y
/--------------------------------------\ | Renaud Guerin - renaudg@hexanet.fr | | rguerin@iut-info.ens.univ-reims.fr | | http://www.hexanet.fr/~renaudg | | CS student (Reims,France) | | Linux supporter http://www.linux.org | \--------------------------------------/
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |