Messages in this thread |  | | Date | Tue, 10 Sep 1996 22:54:11 -0300 (EST) | From | Daniel Lafraia <> | Subject | 2.0.18 Panic |
| |
Hi folks,
I've been running Kernel 2.0.18 for about 5 days (without any boot) then today (1 minute ago) I got a crash. The system was frozen! And I couldn't press CTRL+ALT+DEL. :( Then I had to power the computer off wait some seconds and then turn it on again. My boot as ALMOST well:
-----------------------(DMESG)---------------------------------- Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory structure at 0x000fb2f0 pcibios_init : BIOS32 Service Directory entry at 0xfb790 pcibios_init : PCI BIOS revision 2.10 entry at 0xfb7c0 Probing PCI hardware. Calibrating delay loop.. ok - 39.73 BogoMIPS Memory: 30876k/32768k available (752k kernel code, 384k reserved, 756k data) Swansea University Computer Society NET3.035 for Linux 2.0 NET3: Unix domain sockets 0.12 for Linux NET3.035. Swansea University Computer Society TCP/IP for NET3.034 IP Protocols: IGMP, ICMP, UDP, TCP, IPIP Checking 386/387 coupling... Ok, fpu using exception 16 error reporting. Checking 'hlt' instruction... Ok. Linux version 2.0.18 (root@cpu) (gcc version 2.7.0) #2 Thu Sep 5 14:01:09 EST 1996 Serial driver version 4.13 with no serial options enabled tty00 at 0x03f8 (irq = 4) is a 16550A tty01 at 0x02f8 (irq = 3) is a 16550A Cyclom driver $Revision: 1.36.3.7A $$Date: 1996/07/27 10:25:50 $ Cyclom-Y/ISA #1: 0xd4000-0xd5fff, IRQ12, 16 channels starting from port 0. lp: Driver configured but no interfaces found. Floppy drive(s): fd0 is 1.44M, fd1 is 1.2M Started kswapd v 1.4.2.2 FDC 0 is a post-1991 82077 aic7xxx: BurstLen = 0 DWDs, Latency Timer = 32 PCLKS aic7xxx: AHA-2940 Rev B. aic7xxx: devconfig = 0x580. aic7xxx: Reading SEEPROM...done. aic7xxx: Extended translation enabled. aic7xxx: Memory check yields 16 SCBs, paging not enabled. AHA-2940 (PCI-bus), I/O 0x6000, Mem 0xf0210000: irq 11 bus release time 40 bclks data fifo threshold 100% SCSI CHANNEL A: scsi id 7 scsi selection timeout 256 ms scsi bus reset at power-on enabled scsi bus parity enabled scsi bus termination (low byte) enabled aic7xxx: Downloading sequencer code...done. aic7xxx: Resetting the SCSI bus...done. scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 3.4/3.2/3.1 scsi : 1 host. scsi0: Scanning channel A for devices. scsi0: Target 0, channel A, now synchronous at 10.0MHz, offset 15. Vendor: QUANTUM Model: XP34301 Rev: 1071 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 scsi : detected 1 SCSI disk total. SCSI device sda: hdwr sector= 512 bytes. Sectors= 8410200 [4106 MB] [4.1 GB] tunnel: version v0.2b2 PPP: version 2.2.0 (dynamic channel allocation) TCP compression code copyright 1989 Regents of the University of California PPP Dynamic channel allocation code copyright 1995 Caldera, Inc. PPP line discipline registered. ne.c:v1.10 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov) NE*000 ethercard probe at 0x300: 00 40 05 24 40 cf eth0: NE2000 found at 0x300, using IRQ 5. Partition check: sda: sda1 sda2 VFS: Mounted root (ext2 filesystem) readonly. Adding Swap: 40156k swap-space fcntl_setlk() called by process 51 (lpd) with broken flock() emulation registered device ppp0 registered device ppp1 registered device ppp2 --------------------------------------------------------------------------
Check out on the last 4 lines. :(
When it locks my system up, there were a lot of numbers and "[" and "]" on the screen. :(
Regards, Daniel Lafraia
|  |