Messages in this thread |  | | From | (Chris Adams) | Subject | Problem with NCR 53c810 driver in 2.0.10 | Date | 29 Jul 1996 19:22:32 GMT |
| |
I have a 486DX4-100 motherboard (ASUS PCI/I-486SP3G) with a built-in NCR 53c810 SCSI adapter. I am trying to run Linux on this machine. When I boot up, however, Linux crashes. I can boot this computer from a floppy I made with kernel 2.0.7. Here is the message I get when I boot 2.0.10 from the SCSI hard drive (this is a hand typed copy of the last screenful of information):
FDC 0 is a National Semconductor PC87306 Started kswapd v 1.4.2.2 scsi-ncr53c7,8xx : at PCI bus 0, device 1, function 0 scsi-ncr53c7,8xx : NCR53c810 at memory 0xfbfff000, io 0xe800, irq 9 Unable to handle kernel NULL pointer dereference at virtual address c000000b current->tss.cr3 = 00101000, %cr3 = 00101000 *pde = 00102067 *pte = 00000027 Oops: 0002 CPU: 0 EIP: 0010:[<001868dc>] EFLAGS: 00010286 eax: 00001250 ebx: 07ff8068 ecx: fffffffc edx: ffffffff esi: 07ff8018 edi: 07ff85fc ebp: 00000001 esp: 00014e48 ds: 0018 es: 0018 fs: 002b gs: 0018 ss: 0018 Process swapper (pid: 1, process nr: 1, stackpage=00014000) Stack: 001b0080 00000001 00000002 00000001 fffffffc 00000000 00179c7d 00000000 00000000 00001250 00002278 000001d8 000009c8 00000008 0016f100 3552434e 31386333 00000030 0000000a 00000000 00000000 00000018 0016f41b 00000000 Call Trace: [<00179c7d>] [<0016f100>] [<0016f41b>] [<00186d41>] [<00186e86>] [<001828e4>] [<00180e34>] [<001624e1>] [<0012f818>] [<0010a5b2>] [<0011edb0>] [<001093aa>] [<001091bd>] [<001091c4>] [<00109360>] Code: 89 42 0c 8b 93 08 04 00 00 c7 42 04 00 00 00 00 8b 93 08 04
Here is the output from ksymoops:
Using `/System.map' to map addresses to symbols.
>>EIP: 1868dc <normal_init+4cc/5d0> Trace: 179c7d <clear_selection+d/50> Trace: 16f100 <set_origin+10/60> Trace: 16f41b <lf+2b/60> Trace: 186d41 <ncr_pci_init+361/370> Trace: 186e86 <NCR53c7xx_detect+136/160> Trace: 1828e4 <scsi_init+44/120> Trace: 180e34 <scsi_dev_init+64/1a0> Trace: 1624e1 <device_setup+11/40> Trace: 12f818 <sys_setup+18/50> Trace: 10a5b2 <system_call+52/80> Trace: 11edb0 <kswapd> Trace: 1093aa <init+4a/220> Trace: 1091bd <start_kernel+15d/180> Trace: 1091c4 <start_kernel+164/180> Trace: 1093aa <init+4a/220>
Code: 1868dc <normal_init+4cc/5d0> movl %eax,0xc(%edx) Code: 1868df <normal_init+4cf/5d0> movl 0x408(%ebx),%edx Code: 1868e5 <normal_init+4d5/5d0> movl $0x0,0x4(%edx) Code: 1868ec <normal_init+4dc/5d0> movl 0x90000408(%ebx),%edx Code: 1868f2 <normal_init+4e2/5d0> nop
Here is the kernel .config file:
# # Automatically generated make config: don't edit #
# # Code maturity level options # # CONFIG_EXPERIMENTAL is not set
# # Loadable module support # # CONFIG_MODULES is not set
# # General setup # # CONFIG_MATH_EMULATION is not set CONFIG_NET=y # CONFIG_MAX_16M is not set CONFIG_PCI=y CONFIG_SYSVIPC=y # CONFIG_BINFMT_AOUT is not set CONFIG_BINFMT_ELF=y CONFIG_KERNEL_ELF=y # CONFIG_M386 is not set CONFIG_M486=y # CONFIG_M586 is not set # CONFIG_M686 is not set
# # Floppy, IDE, and other block devices # CONFIG_BLK_DEV_FD=y # CONFIG_BLK_DEV_IDE is not set
# # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_HD_ONLY is not set
# # Additional Block Devices # # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_MD is not set # CONFIG_BLK_DEV_RAM is not set # CONFIG_BLK_DEV_XD is not set # CONFIG_BLK_DEV_HD is not set
# # Networking options # # CONFIG_FIREWALL is not set # CONFIG_NET_ALIAS is not set CONFIG_INET=y # CONFIG_IP_FORWARD is not set # CONFIG_IP_MULTICAST is not set # CONFIG_IP_ACCT is not set
# # (it is safe to leave these untouched) # # CONFIG_INET_PCTCP is not set # CONFIG_INET_RARP is not set # CONFIG_NO_PATH_MTU_DISCOVERY is not set CONFIG_IP_NOSR=y CONFIG_SKB_LARGE=y
# # # # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_AX25 is not set # CONFIG_NETLINK is not set
# # SCSI support # CONFIG_SCSI=y
# # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set
# # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # # CONFIG_SCSI_MULTI_LUN is not set CONFIG_SCSI_CONSTANTS=y
# # SCSI low-level drivers # # CONFIG_SCSI_7000FASST is not set # CONFIG_SCSI_AHA152X is not set # CONFIG_SCSI_AHA1542 is not set # CONFIG_SCSI_AHA1740 is not set # CONFIG_SCSI_AIC7XXX is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_IN2000 is not set # CONFIG_SCSI_AM53C974 is not set # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_DTC3280 is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_EATA_DMA is not set # CONFIG_SCSI_EATA_PIO is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GENERIC_NCR5380 is not set # CONFIG_SCSI_NCR53C406A is not set CONFIG_SCSI_NCR53C7xx=y # CONFIG_SCSI_NCR53C7xx_sync is not set # CONFIG_SCSI_NCR53C7xx_FAST is not set # CONFIG_SCSI_NCR53C7xx_DISCONNECT is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_PAS16 is not set # CONFIG_SCSI_QLOGIC_FAS is not set # CONFIG_SCSI_QLOGIC_ISP is not set # CONFIG_SCSI_SEAGATE is not set # CONFIG_SCSI_T128 is not set # CONFIG_SCSI_U14_34F is not set # CONFIG_SCSI_ULTRASTOR is not set
# # Network device support # CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_EQUALIZER is not set # CONFIG_PLIP is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NET_RADIO is not set CONFIG_NET_ETHERNET=y CONFIG_NET_VENDOR_3COM=y # CONFIG_EL1 is not set # CONFIG_EL2 is not set CONFIG_EL3=y # CONFIG_VORTEX is not set # CONFIG_LANCE is not set # CONFIG_NET_VENDOR_SMC is not set # CONFIG_NET_ISA is not set # CONFIG_NET_EISA is not set # CONFIG_NET_POCKET is not set # CONFIG_TR is not set # CONFIG_ARCNET is not set
# # ISDN subsystem # # CONFIG_ISDN is not set
# # CD-ROM drivers (not for SCSI or IDE/ATAPI drives) # # CONFIG_CD_NO_IDESCSI is not set
# # Filesystems # # CONFIG_QUOTA is not set # CONFIG_LOCK_MANDATORY is not set # CONFIG_MINIX_FS is not set # CONFIG_EXT_FS is not set CONFIG_EXT2_FS=y # CONFIG_XIA_FS is not set # CONFIG_FAT_FS is not set # CONFIG_MSDOS_FS is not set # CONFIG_VFAT_FS is not set # CONFIG_UMSDOS_FS is not set CONFIG_PROC_FS=y CONFIG_NFS_FS=y # CONFIG_ROOT_NFS is not set # CONFIG_SMB_FS is not set # CONFIG_ISO9660_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set
# # Character devices # # CONFIG_SERIAL is not set # CONFIG_DIGI is not set # CONFIG_CYCLADES is not set # CONFIG_STALDRV is not set # CONFIG_RISCOM8 is not set # CONFIG_PRINTER is not set # CONFIG_MOUSE is not set # CONFIG_UMISC is not set # CONFIG_QIC02_TAPE is not set # CONFIG_FTAPE is not set # CONFIG_APM is not set # CONFIG_WATCHDOG is not set # CONFIG_RTC is not set
# # Sound # # CONFIG_SOUND is not set
# # Kernel hacking # # CONFIG_PROFILE is not set -- Chris Adams (C.Adams@Yellow-Jackets.com) "So, if anybody wants to have hardware sent to them: don't call me, but instead write your own unix operating system. It has worked every time for me." - Linus Torvalds, author of Linux (Unix-like) OS
|  |