Messages in this thread |  | | Subject | 2.1.9 mouse sluggish | Date | Thu, 14 Nov 1996 09:57:12 +0100 (MET) | From | Thomas Koenig <> |
| |
I tried out 2.1.9 and found that working under X was difficult, since the mouse pointer didn't follow very well.
Following are the startup messages.
klogd 1.3-0, log source = /proc/kmsg started. Cannot find map file. Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory structure at 0xc00fb130 pcibios_init : BIOS32 Service Directory entry at 0xfb5f0 pcibios_init : PCI BIOS revision 2.10 entry at 0xfb620 Probing PCI hardware. Calibrating delay loop.. ok - 52.84 BogoMIPS Memory: 63264k/65536k available (708k kernel code, 384k reserved, 1180k data) Swansea University Computer Society NET3.035 for Linux 2.0 NET3: Unix domain sockets 0.13 for Linux NET3.035. Swansea University Computer Society TCP/IP for NET3.034 IP Protocols: IGMP, ICMP, UDP, TCP VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting. Checking 'hlt' instruction... Ok. Linux version 2.1.9 (root@mvmap83) (gcc version 2.7.2) #1 Wed Nov 13 18:07:20 MET 1996 POSIX conformance testing by UNIFIX Serial driver version 4.20 with no serial options enabled tty00 at 0x03f8 (irq = 4) is a 16550A tty01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.07 Ramdisk driver initialized : 16 ramdisks of 4096K size Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Started kswapd v 1.4.2.2 ncr53c8xx: at PCI bus 0, device 8, function 0 ncr53c8xx: unit=0 chip=810 rev=0x2 base=0xe4000000, io_port=0x6000, irq=11 ncr53c810-0: using memory mapped IO at virtual address 0xc4841000 ncr53c810-0: requesting shared irq 11 (dev_id=0xc3ff8068) ncr53c810-0: restart (scsi reset). ncr53c8xx: at PCI bus 0, device 11, function 0 ncr53c8xx: unit=1 chip=825 rev=0x2 base=0xe4001000, io_port=0x6200, irq=5 ncr53c825-1: using memory mapped IO at virtual address 0xc4843000 ncr53c825-1: requesting shared irq 5 (dev_id=0xc3ff4068) ncr53c825-1: restart (scsi reset). PPA: unable to initialise controller at 0x378, error 2 scsi0 : ncr53c8xx - revision 1.14c scsi1 : ncr53c8xx - revision 1.14c scsi : 2 hosts. ncr53c810-0-<target 0, lun 0>: using tagged command queueing, up to 4 cmds/lun Vendor: IBM Model: DPES-31080 Rev: S80E Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 ncr53c810-0-<target 1, lun 0>: using tagged command queueing, up to 4 cmds/lun Vendor: IBM Model: DPES-31080 Rev: S80E Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 scsi : detected 2 SCSI disks total. ncr53c810-0-<target 0, lun 0>: 200ns (5 Mb/sec) offset 8. SCSI device sda: hdwr sector= 512 bytes. Sectors= 2118144 [1034 MB] [1.0 GB] ncr53c810-0-<target 1, lun 0>: 200ns (5 Mb/sec) offset 8. SCSI device sdb: hdwr sector= 512 bytes. Sectors= 2118144 [1034 MB] [1.0 GB] Overriding PCI latency timer (CFLT) setting of 32, new value is 255. eth0: 3Com 3c590 Vortex 10Mbps at 0x6100, 00:20:af:d3:7f:60, IRQ 9 Internal config register is 1020012, transceivers 0xe108. 32K byte-wide RAM 1:1 Rx:Tx split, autoselect/10baseT interface. 3c59x.c:v0.25 5/17/96 becker@cesdis.gsfc.nasa.gov Partition check: sda: sda1 sdb: sdb1 sdb2 VFS: Mounted root (ext2 filesystem) readonly. Adding Swap: 130624k swap-space eth0: Initial media type 10baseT. eth0: vortex_open() InternalConfig 01020012. eth0: vortex_open() irq 9 media status 88c0. eth0: Media selection timer tick happened, 10baseT. eth0: Media 10baseT has link beat, 88c0. eth0: Media selection timer finished, 10baseT. -- Thomas Koenig, Thomas.Koenig@ciw.uni-karlsruhe.de, ig25@dkauni2.bitnet. The joy of engineering is to find a straight line on a double logarithmic diagram.
|  |