lkml.org 
[lkml]   [2023]   [Mar]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 3/3] ARM: dts: meson8m2: mxiii-plus: Enable Bluetooth and WiFi support
On 21/03/2023 18:12, Martin Blumenstingl wrote:
> The MXIII Plus uses an Ampak AP6330 Bluetooth and WiFi combo chip.
> Bluetooth is connected to &uart_A and requires toggling GPIOX_20.
> WiFi can be routed to either &sdhc or &sdio. Route WiFi to &sdhc
> since &sdio is already connected to the SD card. Additionally WiFi
> requires toggling GPIOX_11 and GPIOAO_6 as well as enabling the 32kHz
> clock signal.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> ---
> arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 48 ++++++++++++++++++++++-
> 1 file changed, 47 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> index fa6d55f1cfb9..aa4d4bf70629 100644
> --- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> +++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> @@ -19,7 +19,6 @@ aliases {
> ethernet0 = &ethmac;
> i2c0 = &i2c_AO;
> serial0 = &uart_AO;
> - serial1 = &uart_A;
> mmc0 = &sd_card_slot;
> };
>
> @@ -45,12 +44,32 @@ button-function {
> };
> };
>
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> +
> + pinctrl-0 = <&xtal_32k_out_pins>;
> + pinctrl-names = "default";
> +
> + reset-gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>,
> + <&gpio_ao GPIOAO_6 GPIO_ACTIVE_LOW>;
> +
> + clocks = <&xtal_32k_out>;
> + clock-names = "ext_clock";
> + };
> +
> vcc_3v3: regulator-vcc3v3 {
> compatible = "regulator-fixed";
> regulator-name = "VCC3V3";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> };
> +
> + xtal_32k_out: xtal-32k-out-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "xtal_32k_out";
> + };
> };
>
> &cpu0 {
> @@ -192,6 +211,27 @@ &saradc {
> vref-supply = <&vddio_ao1v8>;
> };
>
> +/* SDIO wifi */
> +&sdhc {
> + status = "okay";
> +
> + pinctrl-0 = <&sdxc_a_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <4>;
> + max-frequency = <50000000>;
> +
> + disable-wp;
> + non-removable;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_3v3>;
> +};
> +
> &sdio {
> status = "okay";
>
> @@ -222,6 +262,12 @@ &uart_A {
> pinctrl-0 = <&uart_a1_pins>, <&uart_a1_cts_rts_pins>;
> pinctrl-names = "default";
> uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm20702a1";
> + shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
> + max-speed = <2000000>;
> + };
> };
>
> &uart_AO {

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

\
 
 \ /
  Last update: 2023-03-27 01:12    [W:0.044 / U:1.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site