lkml.org 
[lkml]   [2023]   [Oct]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: phy: fixed link 1000 or 100 set with autoneg off
From


On 10/23/23 15:52, Heiner Kallweit wrote:
> CAUTION: This email comes from a non Wind River email account!
> Do not click links or open attachments unless you recognize the sender and know the content is safe.
>
> On 23.10.2023 09:01, Jia, Fang wrote:
>> Hi Experts,
>>
>> We use NXP LS1046 board and face an issue about the eth interface speed.
>>
>> 1) Scenario
>>
>> we set fixed link 1000Mb/s in device tree.
>>
>> However, after we set the auto-neg off, then the eth1's speed changed to 10M and Duplex changed to Half.
>> The value of /sys/class/net/eth1/speed is 10 and /sys/class/net/eth1/duplex is half
>>
> Why do you set aneg to off? Leave aneg on, that's the only supported
> mode in swphy. 1000Mbps requires aneg anyway per standard.

Thanks very much for your reply.

Actually, due to some reason, the phydev's default aneg state is off.
And we just found if use ethtool to set, it had the same result.

We also found that when we set speed to 100, same result.

So we can assume that swphy only supports the aneg on, no matter the
speed setting. Am I right ?

>
>> 2) Log is as following.
>>
>> # ifconfig eth1 up
>> # ethtool eth1
>> Settings for eth1:
>> Supported ports: [ MII ]
>> Supported link modes: 1000baseT/Full
>> Supported pause frame use: Symmetric Receive-only
>> Supports auto-negotiation: Yes
>>
>> Supported FEC modes: Not reported
>>
>> Advertised link modes: 1000baseT/Full
>> Advertised pause frame use: Symmetric Receive-only
>>
>> Advertised auto-negotiation: Yes
>> Advertised FEC modes: Not reported
>> Speed: 1000Mb/s
>> Duplex: Full
>> Port: MII
>> PHYAD: 1
>> Transceiver: internal
>> Auto-negotiation: on
>> Supports Wake-on: d
>> Wake-on: d
>> Current message level: 0xffffffff (-1)
>> drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol 0xffff8000
>> Link detected: yes
>>
>> # ethtool -s eth1 autoneg off
>> # ethtool eth1
>> Settings for eth1:
>> Supported ports: [ MII ]
>> Supported link modes: 1000baseT/Full
>> Supported pause frame use: Symmetric Receive-only
>> Supports auto-negotiation: Yes
>> Supported FEC modes: Not reported
>> Advertised link modes: 1000baseT/Full
>> Advertised pause frame use: Symmetric Receive-only
>> Advertised auto-negotiation: No
>> Advertised FEC modes: Not reported
>> Speed: 10Mb/s
>> Duplex: Half
>> Port: MII
>> PHYAD: 1
>> Transceiver: internal
>> Auto-negotiation: off
>> Supports Wake-on: d
>> Wake-on: d
>> Current message level: 0xffffffff (-1)
>> drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol 0xffff8000
>> Link detected: yes
>>
>> 3) After code tracing, we found that:
>>
>> phy_state_machine()
>> state PHY_RUNNING: phy_check_link_status()
>> phy_read_status()
>> genphy_read_status()
>> genphy_read_status_fixed()
>>
>> In genphy_read_status_fixed(), the speed and duplex changed.
>> It seems like the bmcr value is always 0x1000 from swphy_read_reg().
>>
>> After revert the commit 726097d6d6d(net: phy: improve auto-neg emulation in swphy), then the Speed and Duplex shown comes back to 1000M and Full.
>>
>> Could you please take a look it ? Can we revert this commit, is there any side impact ?
>>
>> Best Regards,
>> Fang
>

\
 
 \ /
  Last update: 2023-10-23 10:38    [W:0.279 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site