lkml.org 
[lkml]   [2023]   [Oct]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2
Hi,

On 10/10/2023 05:24, Anand Moon wrote:
> On Odroid n2/n2+ previously use gpio-hog to reset the usb hub,
> switch to used on-board usb hub reset to enable the usb hub
> and enable power to hub.
>
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> .../dts/amlogic/meson-g12b-odroid-n2.dtsi | 36 ++++++++++++-------
> 1 file changed, 24 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
> index 91c9769fda20..9e671444eca6 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
> @@ -31,6 +31,30 @@ hub_5v: regulator-hub_5v {
> enable-active-high;
> };
>
> + /* USB hub supports both USB 2.0 and USB 3.0 root hub */
> + usb-hub {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* 2.0 hub on port 1 */
> + hub_2_0: hub@1 {
> + compatible = "usb5e3,610";
> + reg = <1>;
> + peer-hub = <&hub_3_0>;

It seems peer-hub is missing from Documentation/devicetree/bindings/usb/genesys,gl850g.yaml, could you add it ?

Thanks,
Neil

> + vdd-supply = <&usb_pwr_en>;
> + };
> +
> + /* 3.0 hub on port 4 */
> + hub_3_0: hub@2 {
> + compatible = "usb5e3,620";
> + reg = <2>;
> + peer-hub = <&hub_2_0>;
> + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
> + vdd-supply = <&vcc_5v>;
> + };
> + };
> +
> sound {
> compatible = "amlogic,axg-sound-card";
> model = "ODROID-N2";
> @@ -234,18 +258,6 @@ &gpio {
> "PIN_3", /* GPIOX_17 */
> "PIN_5", /* GPIOX_18 */
> "PIN_36"; /* GPIOX_19 */
> - /*
> - * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
> - * to be turned high in order to be detected by the USB Controller
> - * This signal should be handled by a USB specific power sequence
> - * in order to reset the Hub when USB bus is powered down.
> - */
> - usb-hub-hog {
> - gpio-hog;
> - gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
> - output-high;
> - line-name = "usb-hub-reset";
> - };
> };
>
> &i2c3 {

\
 
 \ /
  Last update: 2023-10-10 10:11    [W:0.043 / U:0.228 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site