lkml.org 
[lkml]   [2023]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 2/2] arm64: dts: imx8mp-verdin-dev: Do not include dahlia dtsi
    Date
    From: Philippe Schenker <philippe.schenker@toradex.com>

    Follow the change that has been done on imx8mm-verdin-dev.dtsi and
    remove the include from dahlia to be consistent. Put back all nodes that
    previously had been included.

    Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>

    ---

    .../boot/dts/freescale/imx8mp-verdin-dev.dtsi | 116 +++++++++++++++++-
    1 file changed, 114 insertions(+), 2 deletions(-)

    diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
    index cefabe65b252..361426c0da0a 100644
    --- a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
    +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
    @@ -3,8 +3,6 @@
    * Copyright 2022 Toradex
    */

    -#include "imx8mp-verdin-dahlia.dtsi"
    -
    / {
    /* TODO: Audio Codec */

    @@ -21,16 +19,99 @@ reg_eth2phy: regulator-eth2phy {
    };
    };

    +&backlight {
    + power-supply = <&reg_3p3v>;
    +};
    +
    +/* Verdin SPI_1 */
    +&ecspi1 {
    + status = "okay";
    +};
    +
    +/* EEPROM on display adapter boards */
    +&eeprom_display_adapter {
    + status = "okay";
    +};
    +
    +/* EEPROM on Verdin Development board */
    +&eeprom_carrier_board {
    + status = "okay";
    +};
    +
    +&eqos {
    + status = "okay";
    +};
    +
    &fec {
    phy-supply = <&reg_eth2phy>;
    status = "okay";
    };

    +&flexcan1 {
    + status = "okay";
    +};
    +
    +&flexcan2 {
    + status = "okay";
    +};
    +
    +/* Verdin QSPI_1 */
    +&flexspi {
    + status = "okay";
    +};
    +
    &gpio_expander_21 {
    status = "okay";
    vcc-supply = <&reg_1p8v>;
    };

    +/* Current measurement into module VCC */
    +&hwmon {
    + status = "okay";
    +};
    +
    +&hwmon_temp {
    + vs-supply = <&reg_1p8v>;
    + status = "okay";
    +};
    +
    +/* Verdin I2C_2_DSI */
    +&i2c2 {
    + status = "okay";
    +};
    +
    +&i2c3 {
    + status = "okay";
    +};
    +
    +/* Verdin I2C_1 */
    +&i2c4 {
    + status = "okay";
    +
    + /* TODO: Audio Codec */
    +};
    +
    +/* TODO: Verdin PCIE_1 */
    +
    +/* Verdin PWM_1 */
    +&pwm1 {
    + status = "okay";
    +};
    +
    +/* Verdin PWM_2 */
    +&pwm2 {
    + status = "okay";
    +};
    +
    +/* Verdin PWM_3_DSI */
    +&pwm3 {
    + status = "okay";
    +};
    +
    +&reg_usdhc2_vmmc {
    + vin-supply = <&reg_3p3v>;
    +};
    +
    /* TODO: Verdin I2C_1 with Audio Codec */

    /* Verdin UART_1, connector X50 through RS485 transceiver */
    @@ -38,9 +119,40 @@ &uart1 {
    linux,rs485-enabled-at-boot-time;
    rs485-rts-active-low;
    rs485-rx-during-tx;
    + status = "okay";
    +};
    +
    +/* Verdin UART_2 */
    +&uart2 {
    + status = "okay";
    +};
    +
    +/* Verdin UART_3, used as the Linux Console */
    +&uart3 {
    + status = "okay";
    +};
    +
    +/* Verdin USB_1 */
    +&usb3_0 {
    + status = "okay";
    +};
    +
    +&usb3_phy0 {
    + status = "okay";
    +};
    +
    +/* Verdin USB_2 */
    +&usb3_1 {
    + fsl,permanently-attached;
    + status = "okay";
    +};
    +
    +&usb3_phy1 {
    + status = "okay";
    };

    /* Limit frequency on dev board due to long traces and bad signal integrity */
    &usdhc2 {
    max-frequency = <100000000>;
    + status = "okay";
    };
    --
    2.39.0
    \
     
     \ /
      Last update: 2023-03-26 23:45    [W:4.345 / U:0.072 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site