lkml.org 
[lkml]   [2021]   [Jun]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V2 3/4] vp_vdpa: allow set vq state to initial state after reset
From
Date

在 2021/6/2 下午2:13, Eli Cohen 写道:
> On Wed, Jun 02, 2021 at 10:10:42AM +0800, Jason Wang wrote:
>> We used to fail the set_vq_state() since it was not supported yet by
>> the virtio spec. But if the bus tries to set the state which is equal
>> to the device initial state after reset, we can let it go.
>>
>> This is a must for virtio_vdpa() to set vq state during probe which is
>> required for some vDPA parents.
>>
>> Signed-off-by: Jason Wang <jasowang@redhat.com>
>> ---
>> drivers/vdpa/virtio_pci/vp_vdpa.c | 42 ++++++++++++++++++++++++++++---
>> 1 file changed, 39 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/vdpa/virtio_pci/vp_vdpa.c b/drivers/vdpa/virtio_pci/vp_vdpa.c
>> index c76ebb531212..18bf4a422772 100644
>> --- a/drivers/vdpa/virtio_pci/vp_vdpa.c
>> +++ b/drivers/vdpa/virtio_pci/vp_vdpa.c
>> @@ -210,13 +210,49 @@ static int vp_vdpa_get_vq_state(struct vdpa_device *vdpa, u16 qid,
>> return -EOPNOTSUPP;
>> }
>>
>> +static int vp_vdpa_set_vq_state_split(struct vdpa_device *vdpa,
>> + const struct vdpa_vq_state *state)
>> +{
>> + const struct vdpa_vq_state_split *split = &state->split;
>> +
>> + if (split->avail_index == 0)
>> + return 0;
>> +
>> + return -EOPNOTSUPP;
>> +}
>> +
>> +static int vp_vdpa_set_vq_state_packed(struct vdpa_device *vdpa,
>> + const struct vdpa_vq_state *state)
>> +{
>> + const struct vdpa_vq_state_packed *packed = &state->packed;
>> +
>> + if (packed->last_avail_counter == 1 &&
> Can you elaborate on the requirement on last_avail_counter and
> last_used_counter?


This is required by the virtio spec:

"
2.7.1 Driver and Device Ring Wrap Counters
Each of the driver and the device are expected to maintain, internally,
a single-bit ring wrap counter initialized to 1.
"

For virtio-pci device, since there's no way to assign the value of those
counters, the counters will be reset to 1 after reset, otherwise the
driver can't work.

Thanks


>
>> + packed->last_avail_idx == 0 &&
>> + packed->last_used_counter == 1 &&
>> + packed->last_used_idx == 0)
>> + return 0;
>> +
>> + return -EOPNOTSUPP;
>> +}
>> +
>> static int vp_vdpa_set_vq_state(struct vdpa_device *vdpa, u16 qid,
>> const struct vdpa_vq_state *state)
>> {
>> - /* Note that this is not supported by virtio specification, so
>> - * we return -ENOPOTSUPP here. This means we can't support live
>> - * migration, vhost device start/stop.
>> + struct virtio_pci_modern_device *mdev = vdpa_to_mdev(vdpa);
>> +
>> + /* Note that this is not supported by virtio specification.
>> + * But if the state is by chance equal to the device initial
>> + * state, we can let it go.
>> */
>> + if ((vp_modern_get_status(mdev) & VIRTIO_CONFIG_S_FEATURES_OK) &&
>> + !vp_modern_get_queue_enable(mdev, qid)) {
>> + if (vp_modern_get_driver_features(mdev) &
>> + BIT_ULL(VIRTIO_F_RING_PACKED))
>> + return vp_vdpa_set_vq_state_packed(vdpa, state);
>> + else
>> + return vp_vdpa_set_vq_state_split(vdpa, state);
>> + }
>> +
>> return -EOPNOTSUPP;
>> }
>>
>> --
>> 2.25.1
>>

\
 
 \ /
  Last update: 2021-06-02 09:06    [W:0.680 / U:0.792 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site