lkml.org 
[lkml]   [2021]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 13/13] arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes
Date
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

Add device tree nodes for two i2c blocks: i2c13 and i2c14.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 94bc8b352547..c214ab89b44c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -583,6 +583,44 @@ uart7: serial@99c000 {
};
};

+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x00ac0000 0x0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_data_clk>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_data_clk>;
+ interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
config_noc: interconnect@1500000 {
compatible = "qcom,sm8450-config-noc";
reg = <0 0x01500000 0 0x1c000>;
@@ -683,6 +721,20 @@ tlmm: pinctrl@f100000 {
gpio-ranges = <&tlmm 0 0 211>;
wakeup-parent = <&pdc>;

+ qup_i2c13_data_clk: qup-i2c13-data-clk {
+ pins = "gpio48", "gpio49";
+ function = "qup13";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c14_data_clk: qup-i2c14-data-clk {
+ pins = "gpio52", "gpio53";
+ function = "qup14";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
qup_uart7_rx: qup-uart7-rx {
pins = "gpio26";
function = "qup7";
--
2.31.1
\
 
 \ /
  Last update: 2021-12-09 11:36    [W:0.111 / U:0.624 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site