lkml.org 
[lkml]   [2019]   [Aug]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 5/6] arm64: dts: amlogic: odroid-n2: add minimal thermal zone
Date
Add minimal thermal zone for two temperature sensor
One is located close to the DDR and the other one is
located close to the PLLs (between the CPU and GPU)

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
---
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 60 +++++++++++++++++++
1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
index 75ff8a7e373d..a7d73c0c8447 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -10,6 +10,7 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/meson-g12a-gpio.h>
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+#include <dt-bindings/thermal/thermal.h>

/ {
compatible = "hardkernel,odroid-n2", "amlogic,g12b";
@@ -20,6 +21,55 @@
ethernet0 = &ethmac;
};

+ thermal-zones {
+ cpu-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&cpu_temp>;
+
+ trips {
+ cpu_critical: cpu-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpu_critical>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ ddr-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&ddr_temp>;
+
+ trips {
+ ddr_critical: ddr-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&ddr_critical>;
+ cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
@@ -288,6 +338,7 @@
operating-points-v2 = <&cpu_opp_table_0>;
clocks = <&clkc CLKID_CPU_CLK>;
clock-latency = <50000>;
+ #cooling-cells = <2>;
};

&cpu1 {
@@ -295,6 +346,7 @@
operating-points-v2 = <&cpu_opp_table_0>;
clocks = <&clkc CLKID_CPU_CLK>;
clock-latency = <50000>;
+ #cooling-cells = <2>;
};

&cpu100 {
@@ -302,6 +354,7 @@
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
+ #cooling-cells = <2>;
};

&cpu101 {
@@ -309,6 +362,7 @@
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
+ #cooling-cells = <2>;
};

&cpu102 {
@@ -316,6 +370,7 @@
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
+ #cooling-cells = <2>;
};

&cpu103 {
@@ -323,6 +378,7 @@
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
+ #cooling-cells = <2>;
};

&ext_mdio {
@@ -377,6 +433,10 @@
};
};

+&mali {
+ #cooling-cells = <2>;
+};
+
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
--
2.17.1
\
 
 \ /
  Last update: 2019-08-06 15:08    [W:0.111 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site