lkml.org 
[lkml]   [2019]   [Aug]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v12 3/5] dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver
From
Date
Marc

On 8/16/19 4:38 AM, Marc Kleine-Budde wrote:
> On 5/9/19 6:11 PM, Dan Murphy wrote:
>> DT binding documentation for TI TCAN4x5x driver.
>>
>> Signed-off-by: Dan Murphy <dmurphy@ti.com>
>> ---
>>
>> v12 - No changes - https://lore.kernel.org/patchwork/patch/1052300/
>>
>> v11 - No changes - https://lore.kernel.org/patchwork/patch/1051178/
>> v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/
>> v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/
>> v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/
>> v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/
>> v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/
>>
>> .../devicetree/bindings/net/can/tcan4x5x.txt | 37 +++++++++++++++++++
>> 1 file changed, 37 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt
>>
>> diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
>> new file mode 100644
>> index 000000000000..c388f7d9feb1
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt
>> @@ -0,0 +1,37 @@
>> +Texas Instruments TCAN4x5x CAN Controller
>> +================================================
>> +
>> +This file provides device node information for the TCAN4x5x interface contains.
>> +
>> +Required properties:
>> + - compatible: "ti,tcan4x5x"
>> + - reg: 0
>> + - #address-cells: 1
>> + - #size-cells: 0
>> + - spi-max-frequency: Maximum frequency of the SPI bus the chip can
>> + operate at should be less than or equal to 18 MHz.
>> + - data-ready-gpios: Interrupt GPIO for data and error reporting.
>> + - device-wake-gpios: Wake up GPIO to wake up the TCAN device.
>> +
>> +See Documentation/devicetree/bindings/net/can/m_can.txt for additional
>> +required property details.
>> +
>> +Optional properties:
>> + - reset-gpios: Hardwired output GPIO. If not defined then software
>> + reset.
>> + - device-state-gpios: Input GPIO that indicates if the device is in
>> + a sleep state or if the device is active.
>> +
>> +Example:
>> +tcan4x5x: tcan4x5x@0 {
>> + compatible = "ti,tcan4x5x";
>> + reg = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + spi-max-frequency = <10000000>;
>> + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>;
>> + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
> Can you convert this into a proper interrupt property? E.g.:

OK.  Do you want v13 or do you want patches on top for net-next?

Dan


>
>> interrupt-parent = <&gpio4>;
>> interrupts = <13 0x2>;
> See:
> https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt#L21
> https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/tree/drivers/net/can/spi/mcp251x.c?h=mcp251x#n945

This second link says it invalid

Dan

>
>> + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
>> + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
>> + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
>> +};
> Marc
>

\
 
 \ /
  Last update: 2019-08-22 16:21    [W:0.794 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site