lkml.org 
[lkml]   [2019]   [Aug]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 4/4] dt-bindings: iio: adc: Add AD7606B ADC documentation
    Date
    Documentation for AD7606B Analog to Digital Converter and software
    mode was added.

    Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
    ---
    Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt | 8 ++++++++
    Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml | 4 +++-
    2 files changed, 11 insertions(+), 1 deletion(-)

    diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
    index d8652460198e..9cc7ea19eca6 100644
    --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
    +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
    @@ -7,6 +7,7 @@ Required properties for the AD7606:
    * "adi,ad7606-8"
    * "adi,ad7606-6"
    * "adi,ad7606-4"
    + * "adi,ad7606b"
    * "adi,ad7616"
    - reg: SPI chip select number for the device
    - spi-max-frequency: Max SPI frequency to use
    @@ -42,6 +43,12 @@ Optional properties:
    - adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling
    mode pins. As the line is active high, it should be marked
    GPIO_ACTIVE_HIGH.
    +- adi,sw-mode: Boolean, software mode of operation, so far available only for ad7606b.
    + Software mode is enabled when all three oversampling mode pins are connected to
    + high level. The AD7606B is configured by the corresponding registers. If the
    + adi,oversampling-ratio-gpios property is defined, then the driver will set the
    + oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
    + to VDD.

    Example:

    @@ -63,4 +70,5 @@ Example:
    &gpio 23 GPIO_ACTIVE_HIGH
    &gpio 26 GPIO_ACTIVE_HIGH>;
    standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
    + adi,sw-mode;
    };
    diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
    index 509dbe9c84d2..2afe31747a70 100644
    --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
    +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
    @@ -13,6 +13,7 @@ maintainers:
    description: |
    Analog Devices AD7606 Simultaneous Sampling ADC
    https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
    + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
    https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf

    properties:
    @@ -22,6 +23,7 @@ properties:
    - adi,ad7606-8
    - adi,ad7606-6
    - adi,ad7606-4
    + - adi,ad7606b
    - adi,ad7616

    reg:
    @@ -87,7 +89,7 @@ properties:

    adi,sw-mode:
    description:
    - Software mode of operation, so far available only for ad7616.
    + Software mode of operation, so far available only for ad7616 and ad7606B.
    It is enabled when all three oversampling mode pins are connected to
    high level. The device is configured by the corresponding registers. If the
    adi,oversampling-ratio-gpios property is defined, then the driver will set the
    --
    2.17.1
    \
     
     \ /
      Last update: 2019-08-02 12:10    [W:6.005 / U:0.104 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site