lkml.org 
[lkml]   [2018]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 1/3] mmc: sdhci-esdhc-imx: get rid of support_vsel
Date
> -----Original Message-----
> From: Stefan Agner [mailto:stefan@agner.ch]
> Sent: Thursday, June 28, 2018 4:13 PM
> To: adrian.hunter@intel.com; ulf.hansson@linaro.org
> Cc: Fabio Estevam <fabio.estevam@nxp.com>; Bough Chen
> <haibo.chen@nxp.com>; A.s. Dong <aisheng.dong@nxp.com>;
> michael@amarulasolutions.com; rmk+kernel@armlinux.org.uk; linux-
> mmc@vger.kernel.org; linux-kernel@vger.kernel.org; Stefan Agner
> <stefan@agner.ch>
> Subject: [PATCH 1/3] mmc: sdhci-esdhc-imx: get rid of support_vsel
>
> The field support_vsel is currently only used in the device tree case. Get rid
> of it. No change in behavior.
>

I'm not sure if it's quite necessary to remove it as it's used to bypass
100Mhz above pad settings look up which is meaningless if user claims
no 1-8 v support.

If you remove it, probably you still need better check the quirk for
Pad state look up.

Regards
Dong Aisheng

> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> drivers/mmc/host/sdhci-esdhc-imx.c | 8 ++------
> include/linux/platform_data/mmc-esdhc-imx.h | 2 --
> 2 files changed, 2 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-
> esdhc-imx.c
> index 6f444731754d..20a420b765b3 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -1145,18 +1145,14 @@ sdhci_esdhc_imx_probe_dt(struct
> platform_device *pdev,
> &boarddata->tuning_start_tap);
>
> if (of_find_property(np, "no-1-8-v", NULL))
> - boarddata->support_vsel = false;
> - else
> - boarddata->support_vsel = true;
> + host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
>
> if (of_property_read_u32(np, "fsl,delay-line", &boarddata-
> >delay_line))
> boarddata->delay_line = 0;
>
> mmc_of_parse_voltage(np, &host->ocr_mask);
>
> - /* sdr50 and sdr104 need work on 1.8v signal voltage */
> - if ((boarddata->support_vsel) && esdhc_is_usdhc(imx_data) &&
> - !IS_ERR(imx_data->pins_default)) {
> + if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pins_default))
> {
> imx_data->pins_100mhz = pinctrl_lookup_state(imx_data-
> >pinctrl,
>
> ESDHC_PINCTRL_STATE_100MHZ);
> imx_data->pins_200mhz = pinctrl_lookup_state(imx_data-
> >pinctrl,
> diff --git a/include/linux/platform_data/mmc-esdhc-imx.h
> b/include/linux/platform_data/mmc-esdhc-imx.h
> index 7daa78a2f342..640dec8b5b0c 100644
> --- a/include/linux/platform_data/mmc-esdhc-imx.h
> +++ b/include/linux/platform_data/mmc-esdhc-imx.h
> @@ -34,7 +34,6 @@ enum cd_types {
> * @cd_gpio: gpio for card_detect interrupt
> * @wp_type: type of write_protect method (see wp_types enum above)
> * @cd_type: type of card_detect method (see cd_types enum above)
> - * @support_vsel: indicate it supports 1.8v switching
> */
>
> struct esdhc_platform_data {
> @@ -43,7 +42,6 @@ struct esdhc_platform_data {
> enum wp_types wp_type;
> enum cd_types cd_type;
> int max_bus_width;
> - bool support_vsel;
> unsigned int delay_line;
> unsigned int tuning_step; /* The delay cell steps in tuning
> procedure */
> unsigned int tuning_start_tap; /* The start delay cell point in tuning
> procedure */
> --
> 2.18.0

\
 
 \ /
  Last update: 2018-07-05 04:53    [W:0.107 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site