lkml.org 
[lkml]   [2018]   [Jul]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v10 2/2] media: V3s: Add support for Allwinner CSI.
Hi Yong,

On Thu, Jul 05, 2018 at 03:48:02PM +0800, Yong wrote:
> > > +
> > > +/* -----------------------------------------------------------------------------
> > > + * Media Operations
> > > + */
> > > +static int sun6i_video_formats_init(struct sun6i_video *video,
> > > + const struct media_pad *remote)
> > > +{
> > > + struct v4l2_subdev_mbus_code_enum mbus_code = { 0 };
> > > + struct sun6i_csi *csi = video->csi;
> > > + struct v4l2_format format;
> > > + struct v4l2_subdev *subdev;
> > > + u32 pad;
> > > + const u32 *pixformats;
> > > + int pixformat_count = 0;
> > > + u32 subdev_codes[32]; /* subdev format codes, 32 should be enough */
> > > + int codes_count = 0;
> > > + int num_fmts = 0;
> > > + int i, j;
> > > +
> > > + pad = remote->index;
> > > + subdev = media_entity_to_v4l2_subdev(remote->entity);
> > > + if (subdev == NULL)
> > > + return -ENXIO;
> > > +
> > > + /* Get supported pixformats of CSI */
> > > + pixformat_count = sun6i_csi_get_supported_pixformats(csi, &pixformats);
> > > + if (pixformat_count <= 0)
> > > + return -ENXIO;
> > > +
> > > + /* Get subdev formats codes */
> > > + mbus_code.pad = pad;
> > > + mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE;
> > > + while (!v4l2_subdev_call(subdev, pad, enum_mbus_code, NULL,
> > > + &mbus_code)) {
> >
> > The formats supported by the external sub-device may depend on horizontal
> > and vertical flipping. You shouldn't assume any particular configuration
> > here: instead, bridge drivers generally just need to make sure the formats
> > match in link validation when streaming is started. At least the CSI-2
> > receiver driver and the DMA engine driver (video device) should check the
> > configuration is valid. See e.g. the IPU3 driver:
> > drivers/media/pci/intel/ipu3/ipu3-cio2.c .
>
> Can mbus_code be added dynamically ?
> The code here only enum the mbus code and get the possible supported
> pairs of pixformat and mbus by SoC. Not try to check if the formats
> (width height ...) is valid or not. The formats validation will be
> in link validation when streaming is started as per your advise.

The formats that can be enumerated from the sensor here are those settable
using SUBDEV_S_FMT. The enumeration will change on raw sensors if you use
the flipping controls. As the bridge driver implements MC as well as subdev
APIs, generally the sensor configuration is out of scope of this driver
since it's directly configured from the user space.

Just check that the pipeline is valid before starting streaming in your
driver.

--
Kind regards,

Sakari Ailus
sakari.ailus@linux.intel.com

\
 
 \ /
  Last update: 2018-07-18 11:56    [W:0.094 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site