lkml.org 
[lkml]   [2018]   [Jun]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRE: [PATCH 2/2] dmaengine: xilinx_dma: Enable VDMA S2MM vertical flip support
Date

<Snip>
>
> Vertical flip state is exported in xilinx_vdma_config and depending on IP
> configuration(c_enable_vert_flip) vertical flip state is programmed in
> hardware.
>
> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Acked-by: Kedareswara rao Appana <appanad@xilinx.com>

> ---
> drivers/dma/xilinx/xilinx_dma.c | 22 ++++++++++++++++++++++
> include/linux/dma/xilinx_dma.h | 2 ++
> 2 files changed, 24 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/dma/xilinx/xilinx_dma.c
> b/drivers/dma/xilinx/xilinx_dma.c index 27b5235..c124423 100644
> --- a/drivers/dma/xilinx/xilinx_dma.c
> +++ b/drivers/dma/xilinx/xilinx_dma.c
> @@ -115,6 +115,9 @@
> #define XILINX_VDMA_REG_START_ADDRESS(n) (0x000c + 4 * (n))
> #define XILINX_VDMA_REG_START_ADDRESS_64(n) (0x000c + 8 * (n))
>
> +#define XILINX_VDMA_REG_ENABLE_VERTICAL_FLIP 0x00ec
> +#define XILINX_VDMA_ENABLE_VERTICAL_FLIP BIT(0)
> +
> /* HW specific definitions */
> #define XILINX_DMA_MAX_CHANS_PER_DEVICE 0x20
>
> @@ -340,6 +343,7 @@ struct xilinx_dma_tx_descriptor {
> * @start_transfer: Differentiate b/w DMA IP's transfer
> * @stop_transfer: Differentiate b/w DMA IP's quiesce
> * @tdest: TDEST value for mcdma
> + * @has_vflip: S2MM vertical flip
> */
> struct xilinx_dma_chan {
> struct xilinx_dma_device *xdev;
> @@ -376,6 +380,7 @@ struct xilinx_dma_chan {
> void (*start_transfer)(struct xilinx_dma_chan *chan);
> int (*stop_transfer)(struct xilinx_dma_chan *chan);
> u16 tdest;
> + bool has_vflip;
> };
>
> /**
> @@ -1092,6 +1097,14 @@ static void xilinx_vdma_start_transfer(struct
> xilinx_dma_chan *chan)
> desc->async_tx.phys);
>
> /* Configure the hardware using info in the config structure */
> + if (chan->has_vflip) {
> + reg = dma_read(chan,
> XILINX_VDMA_REG_ENABLE_VERTICAL_FLIP);
> + reg &= ~XILINX_VDMA_ENABLE_VERTICAL_FLIP;
> + reg |= config->vflip_en;
> + dma_write(chan,
> XILINX_VDMA_REG_ENABLE_VERTICAL_FLIP,
> + reg);
> + }
> +
> reg = dma_ctrl_read(chan, XILINX_DMA_REG_DMACR);
>
> if (config->frm_cnt_en)
> @@ -2105,6 +2118,8 @@ int xilinx_vdma_channel_set_config(struct
> dma_chan *dchan,
> }
>
> chan->config.frm_cnt_en = cfg->frm_cnt_en;
> + chan->config.vflip_en = cfg->vflip_en;
> +
> if (cfg->park)
> chan->config.park_frm = cfg->park_frm;
> else
> @@ -2428,6 +2443,13 @@ static int xilinx_dma_chan_probe(struct
> xilinx_dma_device *xdev,
> chan->direction = DMA_DEV_TO_MEM;
> chan->id = chan_id;
> chan->tdest = chan_id - xdev->nr_channels;
> + chan->has_vflip = of_property_read_bool(node,
> + "xlnx,enable-vert-flip");
> + if (chan->has_vflip) {
> + chan->config.vflip_en = dma_read(chan,
> + XILINX_VDMA_REG_ENABLE_VERTICAL_FLIP)
> &
> + XILINX_VDMA_ENABLE_VERTICAL_FLIP;
> + }
>
> chan->ctrl_offset = XILINX_DMA_S2MM_CTRL_OFFSET;
> if (xdev->dma_config->dmatype == XDMA_TYPE_VDMA) { diff
> --git a/include/linux/dma/xilinx_dma.h b/include/linux/dma/xilinx_dma.h
> index 34b98f2..5b6e61e 100644
> --- a/include/linux/dma/xilinx_dma.h
> +++ b/include/linux/dma/xilinx_dma.h
> @@ -27,6 +27,7 @@
> * @delay: Delay counter
> * @reset: Reset Channel
> * @ext_fsync: External Frame Sync source
> + * @vflip_en: Vertical Flip enable
> */
> struct xilinx_vdma_config {
> int frm_dly;
> @@ -39,6 +40,7 @@ struct xilinx_vdma_config {
> int delay;
> int reset;
> int ext_fsync;
> + bool vflip_en;
> };
>
> int xilinx_vdma_channel_set_config(struct dma_chan *dchan,
> --
> 1.7.1

\
 
 \ /
  Last update: 2018-06-25 11:06    [W:0.092 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site