lkml.org 
[lkml]   [2018]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/2] power: supply: sbs-battery: don't assume MANUFACTURER_DATA formats
On Fri, Jun 01, 2018 at 10:23:59AM -0700, Brian Norris wrote:
> This driver was originally submitted for the TI BQ20Z75 battery IC
> (commit a7640bfa10c5 ("power_supply: Add driver for TI BQ20Z75 gas gauge
> IC")) and later renamed to express generic SBS support. While it's
> mostly true that this driver implemented a standard SBS command set, it
> takes liberties with the REG_MANUFACTURER_DATA register. This register
> is specified in the SBS spec, but it doesn't make any mention of what
> its actual contents are.
>
> We've sort of noticed this optionality previously, with commit
> 17c6d3979e5b ("sbs-battery: make writes to ManufacturerAccess
> optional"), where we found that some batteries NAK writes to this
> register.
>
> What this really means is that so far, we've just been lucky that most
> batteries have either been compatible with the TI chip, or else at least
> haven't reported highly-unexpected values.
>
> For instance, one battery I have here seems to report either 0x0000 or
> 0x0100 to the MANUFACTURER_ACCESS_STATUS command -- while this seems to
> match either Wake Up (bits[11:8] = 0000b) or Normal Discharge
> (bits[11:8] = 0001b) status for the TI part [1], they don't seem to
> actually correspond to real states (for instance, I never see 0101b =
> Charge, even when charging).
>
> On other batteries, I'm getting apparently random data in return, which
> means that occasionally, we interpret this as "battery not present" or
> "battery is not healthy".
>
> All in all, it seems to be a really bad idea to make assumptions about
> REG_MANUFACTURER_DATA, unless we already know what battery we're using.
> Therefore, this patch reimplements the "present" and "health" checks to
> the following on most SBS batteries:
>
> 1. HEALTH: report "unknown" -- I couldn't find a standard SBS command
> that gives us much useful here
> 2. PRESENT: just send a REG_STATUS command; if it succeeds, then the
> battery is present
>
> Also, we stop sending MANUFACTURER_ACCESS_SLEEP to non-TI parts. I have
> no proof that this is useful and supported.
>
> If someone explicitly provided a 'ti,bq20z75' compatible property, then
> we retain the existing TI command behaviors.
>
> [1] http://www.ti.com/lit/er/sluu265a/sluu265a.pdf
>
> Signed-off-by: Brian Norris <briannorris@chromium.org>
> ---
> v2:
> * don't stub out POWER_SUPPLY_PROP_PRESENT from sbs_data[]
> * use if/else instead of switch/case
> ---
> drivers/power/supply/sbs-battery.c | 54 +++++++++++++++++++++++++-----
> 1 file changed, 46 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/power/supply/sbs-battery.c b/drivers/power/supply/sbs-battery.c
> index 83d7b4115857..8dea63464a3f 100644
> --- a/drivers/power/supply/sbs-battery.c
> +++ b/drivers/power/supply/sbs-battery.c
> @@ -23,6 +23,7 @@
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/of.h>
> +#include <linux/of_device.h>
> #include <linux/power/sbs-battery.h>
> #include <linux/power_supply.h>
> #include <linux/slab.h>
> @@ -156,6 +157,9 @@ static enum power_supply_property sbs_properties[] = {
> POWER_SUPPLY_PROP_MODEL_NAME
> };
>
> +/* Supports special manufacturer commands from TI BQ20Z75 IC. */
> +#define SBS_FLAGS_TI_BQ20Z75 BIT(0)
> +
> struct sbs_info {
> struct i2c_client *client;
> struct power_supply *power_supply;
> @@ -168,6 +172,7 @@ struct sbs_info {
> u32 poll_retry_count;
> struct delayed_work work;
> struct mutex mode_lock;
> + u32 flags;
> };
>
> static char model_name[I2C_SMBUS_BLOCK_MAX + 1];
> @@ -315,6 +320,27 @@ static int sbs_status_correct(struct i2c_client *client, int *intval)
> static int sbs_get_battery_presence_and_health(
> struct i2c_client *client, enum power_supply_property psp,
> union power_supply_propval *val)
> +{
> + int ret;
> +
> + if (psp == POWER_SUPPLY_PROP_PRESENT) {
> + /* Dummy command; if it succeeds, battery is present. */
> + ret = sbs_read_word_data(client, sbs_data[REG_STATUS].addr);
> + if (ret < 0)
> + val->intval = 0; /* battery disconnected */
> + else
> + val->intval = 1; /* battery present */
> + return 0;
> + } else { /* POWER_SUPPLY_PROP_HEALTH */

Static analyzers may complain that else after return is unnecessary.

Other than that

Reviewed-by: Guenter Roeck <linux@roeck-us.net>

> + /* SBS spec doesn't have a general health command. */
> + val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
> + return 0;
> + }
> +}
> +
> +static int sbs_get_ti_battery_presence_and_health(
> + struct i2c_client *client, enum power_supply_property psp,
> + union power_supply_propval *val)
> {
> s32 ret;
>
> @@ -600,7 +626,12 @@ static int sbs_get_property(struct power_supply *psy,
> switch (psp) {
> case POWER_SUPPLY_PROP_PRESENT:
> case POWER_SUPPLY_PROP_HEALTH:
> - ret = sbs_get_battery_presence_and_health(client, psp, val);
> + if (client->flags & SBS_FLAGS_TI_BQ20Z75)
> + ret = sbs_get_ti_battery_presence_and_health(client,
> + psp, val);
> + else
> + ret = sbs_get_battery_presence_and_health(client, psp,
> + val);
> if (psp == POWER_SUPPLY_PROP_PRESENT)
> return 0;
> break;
> @@ -806,6 +837,7 @@ static int sbs_probe(struct i2c_client *client,
> if (!chip)
> return -ENOMEM;
>
> + chip->flags = (u32)(uintptr_t)of_device_get_match_data(&client->dev);
> chip->client = client;
> chip->enable_detection = false;
> psy_cfg.of_node = client->dev.of_node;
> @@ -915,12 +947,15 @@ static int sbs_suspend(struct device *dev)
> if (chip->poll_time > 0)
> cancel_delayed_work_sync(&chip->work);
>
> - /*
> - * Write to manufacturer access with sleep command.
> - * Support is manufacturer dependend, so ignore errors.
> - */
> - sbs_write_word_data(client, sbs_data[REG_MANUFACTURER_DATA].addr,
> - MANUFACTURER_ACCESS_SLEEP);
> + if (chip->flags & SBS_FLAGS_TI_BQ20Z75) {
> + /*
> + * Write to manufacturer access with sleep command.
> + * Support is manufacturer dependent, so ignore errors.
> + */
> + sbs_write_word_data(client,
> + sbs_data[REG_MANUFACTURER_DATA].addr,
> + MANUFACTURER_ACCESS_SLEEP);
> + }
>
> return 0;
> }
> @@ -941,7 +976,10 @@ MODULE_DEVICE_TABLE(i2c, sbs_id);
>
> static const struct of_device_id sbs_dt_ids[] = {
> { .compatible = "sbs,sbs-battery" },
> - { .compatible = "ti,bq20z75" },
> + {
> + .compatible = "ti,bq20z75",
> + .data = (void *)SBS_FLAGS_TI_BQ20Z75,
> + },
> { }
> };
> MODULE_DEVICE_TABLE(of, sbs_dt_ids);
> --
> 2.17.0.921.gf22659ad46-goog
>

\
 
 \ /
  Last update: 2018-06-01 19:35    [W:0.121 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site