lkml.org 
[lkml]   [2018]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 05/11] ARM: dts: Reflect change of FSL QSPI driver and remove unused properties
From
Date
Hi Boris,

On 30.05.2018 17:10, Boris Brezillon wrote:
> On Wed, 30 May 2018 15:14:34 +0200
> Frieder Schrempf <frieder.schrempf@exceet.de> wrote:
>
>> The FSL QSPI driver was moved to the SPI framework and it now
>> acts as a SPI controller. Therefore the subnodes need to set
>> spi-[rx/tx]-bus-width = <4>, so quad mode is used just as before.
>
> We should try to keep the current behavior even when
> spi-[rx/tx]-bus-width are not defined. How about considering
> spi-[rx/tx]-bus-width as board constraints and then let the core pick
> the best mode based on these constraints plus the SPI NOR chip
> limitations.

Ok, I'll try to adjust this, so we can leave spi-[rx/tx]-bus-width
undefined and still get quad mode as default if possible.

>
>>
>> Also the properties 'bus-num', 'fsl,spi-num-chipselects' and
>> 'fsl,spi-flash-chipselects' were never read by the driver and
>> can be removed.
>>
>> The 'reg' properties are adjusted to reflect the what bus and
>> chipselect the flash is connected to, as the new driver needs
>> this information.
>>
>> The property 'fsl,qspi-has-second-chip' is not needed anymore
>> and will be removed after the old driver was disabled to avoid
>> breaking ls1021a-moxa-uc-8410a.dts.
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
>> ---
>> arch/arm/boot/dts/imx6sx-sdb-reva.dts | 8 ++++++--
>> arch/arm/boot/dts/imx6sx-sdb.dts | 8 ++++++--
>> arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 2 ++
>> arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts | 5 ++---
>> 4 files changed, 16 insertions(+), 7 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
>> index e3533e7..1a6f680 100644
>> --- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
>> +++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
>> @@ -131,13 +131,17 @@
>> #size-cells = <1>;
>> compatible = "spansion,s25fl128s", "jedec,spi-nor";
>> spi-max-frequency = <66000000>;
>> + spi-rx-bus-width = <4>;
>> + spi-tx-bus-width = <4>;
>> };
>>
>> - flash1: s25fl128s@1 {
>> - reg = <1>;
>> + flash1: s25fl128s@2 {
>> + reg = <2>;
>
> Hm, you're breaking backward compat here. Can we try to re-use the
> old numbering scheme instead of patching all DTs?

Unfortunately in the current setup, the definitions for the reg property
are already broken.

For example imx6sx-sdb.dts seems to have one chip connected on bus A,
CS0 and one on bus B, CS0. It has reg set to 0 for the first and 1 for
the second chip.

While fsl-ls208xa-qds.dtsi uses the same hw setup, but has reg set to 0
and 2.

So either way we need to change the reg property at some place.
So the best approach in my opinion is to fix the definitions to use a
single scheme and while at it also remove the fsl,qspi-has-second-chip
property, that is not needed if a single consistent scheme for the reg
properties is used.

Regards,

Frieder

\
 
 \ /
  Last update: 2018-06-01 11:28    [W:0.036 / U:0.528 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site