lkml.org 
[lkml]   [2018]   [May]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 08/13] ALSA: hda/ca0132: Add dsp setup + gpio functions for r3di
Date
Adds dsp setup functions for Recon3Di as well as the GPIO functions
specific to it.

Signed-off-by: Connor McAdams <conmanx360@gmail.com>
---
sound/pci/hda/patch_ca0132.c | 149 ++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 148 insertions(+), 1 deletion(-)

diff --git a/sound/pci/hda/patch_ca0132.c b/sound/pci/hda/patch_ca0132.c
index 37609bd..7a9d505 100644
--- a/sound/pci/hda/patch_ca0132.c
+++ b/sound/pci/hda/patch_ca0132.c
@@ -2904,6 +2904,76 @@ static void ca0132_gpio_setup(struct hda_codec *codec)
}

/*
+ * GPIO control functions for the Recon3D integrated.
+ */
+
+enum r3di_gpio_bit {
+ /* Bit 1 - Switch between front/rear mic. 0 = rear, 1 = front */
+ R3DI_MIC_SELECT_BIT = 1,
+ /* Bit 2 - Switch between headphone/line out. 0 = Headphone, 1 = Line */
+ R3DI_OUT_SELECT_BIT = 2,
+ /*
+ * I dunno what this actually does, but it stays on until the dsp
+ * is downloaded.
+ */
+ R3DI_GPIO_DSP_DOWNLOADING = 3,
+ /*
+ * Same as above, no clue what it does, but it comes on after the dsp
+ * is downloaded.
+ */
+ R3DI_GPIO_DSP_DOWNLOADED = 4
+};
+
+enum r3di_mic_select {
+ /* Set GPIO bit 1 to 0 for rear mic */
+ R3DI_REAR_MIC = 0,
+ /* Set GPIO bit 1 to 1 for front microphone*/
+ R3DI_FRONT_MIC = 1
+};
+
+enum r3di_out_select {
+ /* Set GPIO bit 2 to 0 for headphone */
+ R3DI_HEADPHONE_OUT = 0,
+ /* Set GPIO bit 2 to 1 for speaker */
+ R3DI_LINE_OUT = 1
+};
+enum r3di_dsp_status {
+ /* Set GPIO bit 3 to 1 until DSP is downloaded */
+ R3DI_DSP_DOWNLOADING = 0,
+ /* Set GPIO bit 4 to 1 once DSP is downloaded */
+ R3DI_DSP_DOWNLOADED = 1
+};
+
+static void r3di_gpio_dsp_status_set(struct hda_codec *codec,
+ enum r3di_dsp_status dsp_status)
+{
+ unsigned int cur_gpio;
+
+ /* Get the current GPIO Data setup */
+ cur_gpio = snd_hda_codec_read(codec, 0x01, 0, AC_VERB_GET_GPIO_DATA, 0);
+
+ switch (dsp_status) {
+ case R3DI_DSP_DOWNLOADING:
+ cur_gpio |= (1 << R3DI_GPIO_DSP_DOWNLOADING);
+ snd_hda_codec_write(codec, codec->core.afg, 0,
+ AC_VERB_SET_GPIO_DATA, cur_gpio);
+ break;
+ case R3DI_DSP_DOWNLOADED:
+ /* Set DOWNLOADING bit to 0. */
+ cur_gpio &= ~(1 << R3DI_GPIO_DSP_DOWNLOADING);
+
+ snd_hda_codec_write(codec, codec->core.afg, 0,
+ AC_VERB_SET_GPIO_DATA, cur_gpio);
+
+ cur_gpio |= (1 << R3DI_GPIO_DSP_DOWNLOADED);
+ break;
+ }
+
+ snd_hda_codec_write(codec, codec->core.afg, 0,
+ AC_VERB_SET_GPIO_DATA, cur_gpio);
+}
+
+/*
* PCM callbacks
*/
static int ca0132_playback_pcm_prepare(struct hda_pcm_stream *hinfo,
@@ -4539,6 +4609,30 @@ static void ca0132_refresh_widget_caps(struct hda_codec *codec)
}

/*
+ * Recon3Di r3di_setup_defaults sub functions.
+ */
+
+static void r3di_dsp_initial_mic_setup(struct hda_codec *codec)
+{
+ unsigned int tmp;
+
+ /* Mic 1 Setup */
+ chipio_set_conn_rate(codec, MEM_CONNID_MICIN1, SR_96_000);
+ chipio_set_conn_rate(codec, MEM_CONNID_MICOUT1, SR_96_000);
+ /* This ConnPointID is unique to Recon3Di. Haven't seen it elsewhere */
+ chipio_set_conn_rate(codec, 0x0F, SR_96_000);
+ tmp = FLOAT_ONE;
+ dspio_set_uint_param(codec, 0x80, 0x00, tmp);
+
+ /* Mic 2 Setup, even though it isn't connected on SBZ */
+ chipio_set_conn_rate(codec, MEM_CONNID_MICIN2, SR_96_000);
+ chipio_set_conn_rate(codec, MEM_CONNID_MICOUT2, SR_96_000);
+ chipio_set_conn_rate(codec, 0x0F, SR_96_000);
+ tmp = FLOAT_ZERO;
+ dspio_set_uint_param(codec, 0x80, 0x01, tmp);
+}
+
+/*
* Initialize Sound Blaster Z analog microphones.
*/
static void sbz_init_analog_mics(struct hda_codec *codec)
@@ -4700,6 +4794,50 @@ static void ca0132_setup_defaults(struct hda_codec *codec)
}

/*
+ * Setup default parameters for Recon3Di DSP.
+ */
+
+static void r3di_setup_defaults(struct hda_codec *codec)
+{
+ struct ca0132_spec *spec = codec->spec;
+ unsigned int tmp;
+ int num_fx;
+ int idx, i;
+
+ if (spec->dsp_state != DSP_DOWNLOADED)
+ return;
+
+
+ r3di_dsp_initial_mic_setup(codec);
+
+ /*remove DSP headroom*/
+ tmp = FLOAT_ZERO;
+ dspio_set_uint_param(codec, 0x96, 0x3C, tmp);
+
+ /* set WUH source */
+ tmp = FLOAT_TWO;
+ dspio_set_uint_param(codec, 0x31, 0x00, tmp);
+ chipio_set_conn_rate(codec, MEM_CONNID_WUH, SR_48_000);
+
+ /* Set speaker source? */
+ dspio_set_uint_param(codec, 0x32, 0x00, tmp);
+
+ r3di_gpio_dsp_status_set(codec, R3DI_DSP_DOWNLOADED);
+
+ /* Setup effect defaults */
+ num_fx = OUT_EFFECTS_COUNT + IN_EFFECTS_COUNT + 1;
+ for (idx = 0; idx < num_fx; idx++) {
+ for (i = 0; i <= ca0132_effects[idx].params; i++) {
+ dspio_set_uint_param(codec,
+ ca0132_effects[idx].mid,
+ ca0132_effects[idx].reqs[i],
+ ca0132_effects[idx].def_vals[i]);
+ }
+ }
+
+}
+
+/*
* Setup default parameters for the Sound Blaster Z DSP. A lot more going on
* than the Chromebook setup.
*/
@@ -5397,6 +5535,7 @@ static void ca0132_alt_init(struct hda_codec *codec)
codec_dbg(codec, "R3DI alt_init");
ca0132_gpio_init(codec);
ca0132_gpio_setup(codec);
+ r3di_gpio_dsp_status_set(codec, R3DI_DSP_DOWNLOADING);
r3di_pre_dsp_setup(codec);
snd_hda_sequence_write(codec, spec->chip_init_verbs);
snd_hda_codec_write(codec, WIDGET_CHIP_CTRL, 0, 0x6FF, 0xC4);
@@ -5445,21 +5584,29 @@ static int ca0132_init(struct hda_codec *codec)
ca0132_init_unsol(codec);
ca0132_init_params(codec);
ca0132_init_flags(codec);
+
snd_hda_sequence_write(codec, spec->base_init_verbs);

if (spec->quirk != QUIRK_NONE)
ca0132_alt_init(codec);

ca0132_download_dsp(codec);
+
ca0132_refresh_widget_caps(codec);

if (spec->quirk == QUIRK_SBZ)
writew(0x0107, spec->mem_base + 0x320);

- if (spec->quirk != QUIRK_SBZ) {
+ switch (spec->quirk) {
+ case QUIRK_R3DI:
+ r3di_setup_defaults(codec);
+ break;
+ case QUIRK_NONE:
+ case QUIRK_ALIENWARE:
ca0132_setup_defaults(codec);
ca0132_init_analog_mic2(codec);
ca0132_init_dmic(codec);
+ break;
}

for (i = 0; i < spec->num_outputs; i++)
--
2.7.4
\
 
 \ /
  Last update: 2018-05-08 19:24    [W:0.128 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site