lkml.org 
[lkml]   [2018]   [May]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 4/7] dt-bindings: gnss: add u-blox binding
* Tony Lindgren <tony@atomide.com> [180508 08:54]:
> * Tony Lindgren <tony@atomide.com> [180508 08:47]:
> > * Tony Lindgren <tony@atomide.com> [180508 08:22]:
> > > * Johan Hovold <johan@kernel.org> [180508 07:00]:
> > > > With the negative autosuspend set in both omap drivers probe functions,
> > > > this is the expected behaviour. Which I think we must fix.
> > >
> > > Yes indeed. I've been using my script for years now and have
> > > completely missed the fact that the unused ports are not idled
> > > at all on start-up when unused.
> >
> > This might be all that's needed, care to try it and if it works
> > I'll send out two separate proper patches?
> >
> > I'm seeing this now on my bbb after temporarily disabling my
> > UART idle init script:
> >
> > # rwmem -s32 0x44e004b4 # uart 1 on l4_wkup
> > 0x44e004b4 = 0x00000002
> >
> > # rwmem -s32 0x44e0006c+0x10 # uart 2 - 5 on l4_per
> > 0x44e0006c = 0x00030000
> > 0x44e00070 = 0x00030000
> > 0x44e00074 = 0x00030000
> > 0x44e00078 = 0x00030000
> >
> > # rwmem -s32 0x44e00038 # uart 6 on l4_per
> > 0x44e00038 = 0x00030000
>
> Hmm I forgot to remove status = "disabled" from the other ports,
> still not idling the unused ports with the patch below it seems.

No need to enable/disable autosuspend except in startup and shutdown
I think. The patch below works for me, now includes removal of the
status = "disabled" flags too. Only tested with 8250_omap on bbb
so far.

I wonder if other places still need fixing for autosuspend
like console support?

Regards,

Tony

8< -------------------
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -347,7 +347,6 @@
clock-frequency = <48000000>;
reg = <0x44e09000 0x2000>;
interrupts = <72>;
- status = "disabled";
dmas = <&edma 26 0>, <&edma 27 0>;
dma-names = "tx", "rx";
};
@@ -358,7 +357,6 @@
clock-frequency = <48000000>;
reg = <0x48022000 0x2000>;
interrupts = <73>;
- status = "disabled";
dmas = <&edma 28 0>, <&edma 29 0>;
dma-names = "tx", "rx";
};
@@ -369,7 +367,6 @@
clock-frequency = <48000000>;
reg = <0x48024000 0x2000>;
interrupts = <74>;
- status = "disabled";
dmas = <&edma 30 0>, <&edma 31 0>;
dma-names = "tx", "rx";
};
@@ -380,7 +377,6 @@
clock-frequency = <48000000>;
reg = <0x481a6000 0x2000>;
interrupts = <44>;
- status = "disabled";
};

uart4: serial@481a8000 {
@@ -389,7 +385,6 @@
clock-frequency = <48000000>;
reg = <0x481a8000 0x2000>;
interrupts = <45>;
- status = "disabled";
};

uart5: serial@481aa000 {
@@ -398,7 +393,6 @@
clock-frequency = <48000000>;
reg = <0x481aa000 0x2000>;
interrupts = <46>;
- status = "disabled";
};

i2c0: i2c@44e0b000 {
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -605,6 +605,7 @@ static int omap_8250_startup(struct uart_port *port)
return ret;
}

+ pm_runtime_use_autosuspend(port->dev);
pm_runtime_get_sync(port->dev);

up->mcr = 0;
@@ -685,8 +686,8 @@ static void omap_8250_shutdown(struct uart_port *port)
serial_out(up, UART_LCR, up->lcr & ~UART_LCR_SBC);
serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);

- pm_runtime_mark_last_busy(port->dev);
- pm_runtime_put_autosuspend(port->dev);
+ pm_runtime_dont_use_autosuspend(port->dev);
+ pm_runtime_put_sync(port->dev);
free_irq(port->irq, port);
dev_pm_clear_wake_irq(port->dev);
}
@@ -1226,7 +1227,7 @@ static int omap8250_probe(struct platform_device *pdev)
spin_lock_init(&priv->rx_dma_lock);

device_init_wakeup(&pdev->dev, true);
- pm_runtime_use_autosuspend(&pdev->dev);
+ /* See omap_8250_startup and shutdown for autosuspend */
pm_runtime_set_autosuspend_delay(&pdev->dev, -1);

pm_runtime_irq_safe(&pdev->dev);
@@ -1265,8 +1266,8 @@ static int omap8250_probe(struct platform_device *pdev)
}
priv->line = ret;
platform_set_drvdata(pdev, priv);
- pm_runtime_mark_last_busy(&pdev->dev);
- pm_runtime_put_autosuspend(&pdev->dev);
+ pm_runtime_put_sync(&pdev->dev);
+
return 0;
err:
pm_runtime_dont_use_autosuspend(&pdev->dev);
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -740,6 +740,7 @@ static int serial_omap_startup(struct uart_port *port)

dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);

+ pm_runtime_use_autosuspend(up->dev);
pm_runtime_get_sync(up->dev);
/*
* Clear the FIFO buffers and disable them.
@@ -821,8 +822,8 @@ static void serial_omap_shutdown(struct uart_port *port)
if (serial_in(up, UART_LSR) & UART_LSR_DR)
(void) serial_in(up, UART_RX);

- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
+ pm_runtime_dont_use_autosuspend(up->dev);
+ pm_runtime_put_sync(up->dev);
free_irq(up->port.irq, up);
dev_pm_clear_wake_irq(up->dev);
}
@@ -1733,7 +1734,7 @@ static int serial_omap_probe(struct platform_device *pdev)
omap_up_info->autosuspend_timeout = -1;

device_init_wakeup(up->dev, true);
- pm_runtime_use_autosuspend(&pdev->dev);
+ /* See serial_omap_startup and shutdown for autosuspend */
pm_runtime_set_autosuspend_delay(&pdev->dev,
omap_up_info->autosuspend_timeout);

@@ -1751,8 +1752,7 @@ static int serial_omap_probe(struct platform_device *pdev)
if (ret != 0)
goto err_add_port;

- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
+ pm_runtime_put_sync(&pdev->dev);
return 0;

err_add_port:
\
 
 \ /
  Last update: 2018-05-08 18:49    [W:1.386 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site