lkml.org 
[lkml]   [2018]   [May]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Dell docking station & Dell Embedded Controller & PS/2 devices
On Thursday 01 February 2018 11:29:45 Dmitry Torokhov wrote:
> Hi Pali,
>
> On Wed, Jan 24, 2018 at 11:41:21AM +0100, Pali Rohár wrote:
> > Hi Dmitry!
> >
> > I'm observing a problem with internal touchpad (handled by psmouse.ko)
> > on Dell laptops connected to Dell E docking station. When I connect
> > external PS/2 keyboard to docking station then internal laptop touchpad
> > switch from multitouch absolute mode to relative bare PS/2 mode.
> >
> > And because ALPS driver in psmouse.ko is capable to process interleaved
> > bare 3-byte PS/2 packets with 6-byte ALPS packets (which handles
> > trackstick data on some ALPS models), ALPS driver does not show any
> > message about this "downgrade" from multitouch to bare mode. And
> > continue working in bare mode.
> >
> > When I rmmod psmouse and modprobe it again, then touchpad switch back to
> > multitouch mode.
> >
> > Mario told me that Dell Embedded Controller, which handle internal
> > keyboard, internal touchpad and external PS/2 keyboard, automatically
> > send RESET command to *all* those devices when external PS/2 keyboard is
> > connected. Therefore this is reason why touchpad downgrade to to bare
> > mode. And according to Mario, host system should issue vendor specific
> > PS/2 commands to re-initialize all PS/2 devices when this situation
> > happen. Mario also told me that Windows is doing this action.
>
> Yeah, I remember fun with Inspiron 8100 - when you dock it it woudl
> silently switch Synaptics touchpad into standard mode and it would not
> come back as Synaptics until you disconnect. And there was no
> notification to the kernel as far as I could tell.
>
> It could be that we need to monitor dock events and then kick reconnect
> of serio port, either from userspace via udev (I think that would be
> preferred), or in kernel.
>
> >
> > Every time when I connect external PS/2 keyboard to dock I see this
> > message in dmesg:
> >
> > Spurious ACK... Some program might be trying to access hardware directly.
> >
> > I see it also every time when I dock laptop into docking station (to
> > which is keyboard already connected). And it happens also when I connect
> > external PS/2 mouse to dock.
> >
> > Dmitry, how to handle this situation to re-initialize psmouse.ko when
> > external PS/2 device is connected to Dell E docking station? According
> > to Mario, this is how Dell Embedded Controller is designed and suppose
> > how OS should work with it.
> >
> > Manually rmmoding and modprobing for every docking/undocking laptop is
> > not ideal solution.
> >
> > Could it be possible to use that Spurious ATKBD_RET_ACK from atkbd.c be
> > handled on Dell systems (probably via DMI) as an event to reset and
> > reinitialize all PS/2 devices?
>
> So we need to figure out what exactly we are getting from the docking
> station in this case. We do try to handle the new device 0xaa 0x00
> announcements:
>
> /* Check if this is a new device announcement (0xAA 0x00) */
> if (unlikely(psmouse->packet[0] == PSMOUSE_RET_BAT && psmouse->pktcnt <= 2)) {
> if (psmouse->pktcnt == 1) {
> psmouse->last = jiffies;
> goto out;
> }
>
> if (psmouse->packet[1] == PSMOUSE_RET_ID ||
> (psmouse->protocol->type == PSMOUSE_HGPK &&
> psmouse->packet[1] == PSMOUSE_RET_BAT)) {
> __psmouse_set_state(psmouse, PSMOUSE_IGNORE);
> serio_reconnect(serio);
> goto out;
> }
>
> ...
>
> I am not sure where the "spurious ACK comes from". Can you enable i8042
> debug before trying to dock and capture the data stream from the mouse?
>
> Thanks.
>

Hi Dmitry!

I enabled unmask_kbd_data and debug and here is output from dmesg.

echo Y > /sys/module/i8042/parameters/debug
echo Y > /sys/module/i8042/parameters/unmask_kbd_data

PS/2 keyboard is already connected in dock and laptop was just docked:

[25461.552314] i8042: [6365474] fa <- i8042 (interrupt, 0, 1)
[25461.552319] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[25462.707296] i8042: [6365763] ed -> i8042 (kbd-data)
[25462.851289] i8042: [6365799] fa <- i8042 (interrupt, 0, 1)
[25462.851303] i8042: [6365799] 00 -> i8042 (kbd-data)
[25462.858437] i8042: [6365801] fa <- i8042 (interrupt, 0, 1)
[25462.869512] i8042: [6365804] fa <- i8042 (interrupt, 0, 1)
[25462.869517] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[25463.670515] i8042: [6366004] ed -> i8042 (kbd-data)
[25463.670647] i8042: [6366004] fa <- i8042 (interrupt, 0, 1)
[25463.670655] i8042: [6366004] 02 -> i8042 (kbd-data)
[25463.676769] i8042: [6366005] fa <- i8042 (interrupt, 0, 1)


Laptop is docked and PS/2 keyboard was just connected:

[26571.014368] i8042: [6642848] fa <- i8042 (interrupt, 0, 1)
[26571.014380] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.


In both cases there is no events from touchpad, only from keyboard. So
Dell EC silently reset PS/2 touchpad when PS/2 keyboard is attached.

So I think we should capture 0xFA and on Dell machines we should
reinitialize PS/2 drivers. As there is really nothing more then 0xFA.

--
Pali Rohár
pali.rohar@gmail.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-05-06 15:48    [W:0.076 / U:0.112 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site