lkml.org 
[lkml]   [2018]   [May]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v7 3/9] PCI: endpoint: functions/pci-epf-test: Add second entry
On Fri, May 04, 2018 at 11:28:58AM +0530, Kishon Vijay Abraham I wrote:
> Hi Lorenzo,
>
> On Thursday 03 May 2018 07:46 PM, Lorenzo Pieralisi wrote:
> > On Thu, May 03, 2018 at 12:03:15PM +0530, Kishon Vijay Abraham I wrote:
> >
> > [...]
> >
> >>>> Since the linkup notifier and BAR index (where auxiliary registers are
> >>>> located) may be configurable and is something platform dependent,
> >>>> perhaps the configuration of this variables should be done by module
> >>>> parameter and not by configfs, leaving this configuration
> >>>> responsibility in charge of each platform.
> >>>
> >>> They are platform dependent because they depend on the EP controller.
> >>> That's why I said that those are EP controller parameters. I do not
> >>> think they are module parameters either - they should be part of HW
> >>> description in firmware.
> >>
> >> The problem is because pci-epf-test cannot be described in HW. pci-epf-test is
> >> also not automatically bound to the EP controller but is bound by the user like
> >> below
> >> ln -s functions/pci_epf_test/func1 controllers/51000000.pcie_ep/
> >>
> >> So given that user anyways has to bind the epf device to the controller, based
> >> on the platform the user can use a different configfs entry like below
> >> ln -s functions/pci_epf_test_dw/func1 controllers/51000000.pcie_ep/ or
> >> ln -s functions/pci_epf_test_k2g/func1 controllers/21800000.pcie-ep/
> >>
> >> If the epf can be described in dt, then something like below can be done
> >> pcie1_ep: pcie_ep@51000000 {
> >> compatible = "ti,dra7-pcie-ep";
> >> interrupts = <0 232 0x4>;
> >> num-lanes = <1>;
> >> num-ib-windows = <4>;
> >> num-ob-windows = <16>;
> >> phys = <&pcie1_phy>;
> >> phy-names = "pcie-phy0";
> >> pci_epf_test: pci_epf_test@0 {
> >> name = "pci_epf_test_dw";
> >> <other properties>;
> >> }
> >> };
> >>
> >> With this pci-dra7xx.c driver should create pci_epf_device using
> >> pci_epf_create("pci_epf_test_dw");
> >>
> >> Then the driver_data corresponding to "pci_epf_test_dw" will select linkup
> >> notifier or BAR index etc.
> >
> > Those two properties are properties of the EP controller (it is not 100%
> > clear to me how the test BAR register is defined), is this correct ?
>
> Right, these properties are specific to a platform. In some of the platforms
> like K2G (BAR0 is reserved i.e it is used to map PCIe app registers and cannot
> be used by pci_epf_test. In such cases we should use a BAR other than BAR0).

I do not think those properties are pci_epf_test specific, that's the
whole point I am making. Those are EPC controller features.

> > If yes, given that those properties are not useful before an EPF is
> > bound to an EPC, can't they be retrieved at bind time from the EPC
> > controller data (that we can add through DT bindings) ?
>
> hmm..
>
> We can have quirk in pci_epc, something like below
>
> struct pci_epc {
> .
> .
> unsigned int quirks;
> .
> .
> };
>
> #define EPC_QUIRKS_NO_LINKUP_NOTIFIER BIT(0)
> #define EPC_QUIRKS_BAR0_RESERVED BIT(1)
> #define EPC_QUIRKS_BAR1_RESERVED BIT(2)
> #define EPC_QUIRKS_BAR2_RESERVED BIT(3)
> #define EPC_QUIRKS_BAR3_RESERVED BIT(4)
> #define EPC_QUIRKS_BAR4_RESERVED BIT(5)
> #define EPC_QUIRKS_BAR5_RESERVED BIT(6)
>
> The controller driver can set the appropriate quirks
> epc->quirks |= EPC_QUIRKS_NO_LINKUP_NOTIFIER | EPC_QUIRKS_BAR0_RESERVED;
>
> Then pci-epf-test driver can checks the quirks to see the supported EPC features.
>
> Does something like above looks okay to you?

Well, it is better than the driver_data approach, I would not call them
quirks but features and for the BARs you should define a mask it does
not make sense to enumerate them. It is probably a good idea to leave
room for additional "features" so please choose the bits placement
wisely.

Thanks,
Lorenzo

\
 
 \ /
  Last update: 2018-05-04 13:19    [W:0.063 / U:1.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site