lkml.org 
[lkml]   [2018]   [May]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] serial: 8250: omap: Fix idling of clocks for unused uarts
From
Date


On Wednesday 02 May 2018 10:45 PM, Tony Lindgren wrote:
> I noticed that unused UARTs won't necessarily idle properly always
> unless at least one byte tx transfer is done first.
>
> After some debugging I narrowed down the problem to the scr register
> dma configuration bits that need to be set before softreset for the
> clocks to idle. Unless we do this, the module clkctrl idlest bits
> may be set to 1 instead of 3 meaning the clock will never idle and
> is blocking deeper idle states for the whole domain.
>
> This might be related to the configuration done by the bootloader
> or kexec booting where certain configurations cause the 8250 or
> the clkctrl clock to jam in a way where setting of the scr bits
> and reset is needed to clear it. I've tried diffing the 8250
> registers for the various modes, but did not see anything specific.
> So far I've only seen this on omap4 but I'm suspecting this might
> also happen on the other clkctrl using SoCs considering they
> already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.
>

That's interesting! We do have AM437x suspend/resume working without
this workaround (UARTs on AM437x does not use DMA) and UART IPs clkctrl
do go to idle state. Seems like a OMAP4 specific issue.

> Let's fix the issue by configuring scr before reset for basic dma
> even if we don't use it. The scr register will be reset when we do
> softreset few lines after, and we restore scr on resume. We should
> do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
> set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
> using clkctrl similar to omap4.
>
> Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
> bits are needed for the clkctrl to idle after a softreset.
>
> And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
> for the related workaround to be enabled. This same compatible
> value will also be used for omap5.
>
> Fixes: cdb929e4452a ("serial: 8250_omap: workaround errata around
> idling UART after using DMA")
> Cc: Keerthy <j-keerthy@ti.com>
> Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> Cc: Sekhar Nori <nsekhar@ti.com>
> Cc: Tero Kristo <t-kristo@ti.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> drivers/tty/serial/8250/8250_omap.c | 13 ++++++++++++-
> 1 file changed, 12 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
> --- a/drivers/tty/serial/8250/8250_omap.c
> +++ b/drivers/tty/serial/8250/8250_omap.c
> @@ -1110,13 +1110,14 @@ static int omap8250_no_handle_irq(struct uart_port *port)
> return 0;
> }
>
> +static const u8 omap4_habit = UART_ERRATA_CLOCK_DISABLE;
> static const u8 am3352_habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE;
> static const u8 dra742_habit = UART_ERRATA_CLOCK_DISABLE;
>
> static const struct of_device_id omap8250_dt_ids[] = {
> { .compatible = "ti,omap2-uart" },
> { .compatible = "ti,omap3-uart" },
> - { .compatible = "ti,omap4-uart" },
> + { .compatible = "ti,omap4-uart", .data = &omap4_habit, },
> { .compatible = "ti,am3352-uart", .data = &am3352_habit, },
> { .compatible = "ti,am4372-uart", .data = &am3352_habit, },
> { .compatible = "ti,dra742-uart", .data = &dra742_habit, },
> @@ -1362,6 +1363,16 @@ static int omap8250_soft_reset(struct device *dev)
> int sysc;
> int syss;
>
> + /*
> + * At least on omap4, unused uarts may not idle after reset without
> + * a basic scr dma configuration even with no dma in use. The
> + * module clkctrl status bit will stay set blocking idle for the
> + * whole clockdomain. The softreset below will clear scr, and we
> + * restore it on resume so this is safe to do on all SoCs needing
> + * omap8250_soft_reset() quirk.
> + */
> + serial_out(up, UART_OMAP_SCR,
> + OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL);

Comment in omap8250_update_scr() warns not to set these two bits in a
single register write because this may lead to malfunction. I would
recommend to split this into two writes.

> sysc = serial_in(up, UART_OMAP_SYSC);
>
> /* softreset the UART */
>

--
Regards
Vignesh

\
 
 \ /
  Last update: 2018-05-03 12:19    [W:0.293 / U:0.296 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site