lkml.org 
[lkml]   [2018]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mtd: nand: raw: atmel: add module param to avoid using dma
From
Date


On 28.05.2018 13:10, Peter Rosin wrote:
> On 2018-05-28 00:11, Peter Rosin wrote:
>> On 2018-05-27 11:18, Peter Rosin wrote:
>>> On 2018-05-25 16:51, Tudor Ambarus wrote:
>>>> We think the best way is to keep LCD on DDR Ports 2 and 3 (8th and 9th
>>>> slaves), to have maximum bandwidth and to use DMA on DDR port 1 for NAND
>>>> (7th slave).
>>>
>>> Exactly how do I accomplish that?
>>>
>>> I can see how I can move the LCD between slave DDR port 2 and 3 by
>>> selecting LCDC DMA master 8 or 9 (but according to the above it should
>>> not matter). The big question is how I control what slave the NAND flash
>>> is going to use? I find nothing in the datasheet, and the code is also
>>> non-transparent enough for me to figure it out by myself without
>>> throwing out this question first...

>> [...]

>> and the output is
>>
>> atmel-nand-controller 10000000.ebi:nand-controller: using dma0chan5 for DMA transfers
>>
>> So, DMA controller 0 is in use. I still don't know if IF0, IF1 or IF2 is used
>> or how to find out. I guess IF2 is not in use since that does not allow any
>> DDR2 port as slave...

Hello Peter,

Thank you for all the information, I will chip in to help a little bit.
The Master/channel is described in the device tree. The channel has a
controller, a mem/periph interface and a periph ID, plus a FIFO
configuration.

The dma chan number reported in the dmesg is just software. Here is an
example from DT:
dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(1)>,
<&dma0 2 AT91_DMA_CFG_PER_ID(2)>;

you can match this with the help from
Documentation/devicetree/bindings/dma/atmel-dma.txt:

1. A phandle pointing to the DMA controller.

2. The memory interface (16 most significant bits), the peripheral
interface
(16 less significant bits).

3. Parameters for the at91 DMA configuration register which are device

dependent:

- bit 7-0: peripheral identifier for the hardware handshaking
interface. The
identifier can be different for tx and rx.

- bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 2 for ASAP.


So , what was Tudor asking for, is your DT for the ebi node (if you are
using ebi), or, your NFC SRAM (Nand Flash Controller SRAM) DMA
devicetree chunk, so, we can figure out which type of DMA are you using.

Normally, the ebi should be connected to both DMA0 and DMA1 on those
interfaces specified in DT. Which ones you want to use, depends on your
setup (and contention on the bus/accesses, like in your case, the HLCDC)

Thats why we have multiple choices, to pick the right one for each case.
In our vanilla DT sama5d3.dtsi we do not have DMA described for ebi
interface.

Eugen

>> [...]

\
 
 \ /
  Last update: 2018-05-29 08:34    [W:0.258 / U:0.772 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site